Kogan Cordless Portable Travel Water Flosser User manual

CORDLESS PORTABLE
TRAVEL WATER FLOSSER
KACLPRWTFLA

Ensure you have read and fully understood all these instructions. Retain this user guide for
future reference.
Important Safety Instructions
• Do not use this appliance unless you fully understand the operating and safety
instructions.
• Do not operate this appliance in any other way other than what it outlined in this
user guide.
• Do not dismantle or modify this appliance as this may cause damage and electric
shock.
• Do not fill the water tank with water exceeding 40°C.
• If the appliance is dropped in water while charging, always unplug it before
attempting to remove it from the water.Cease use immediately and contact
Kogan.com for support.
• Do not operate any appliance with a damaged charger, cord or plug or after the
appliance malfunctions or has been damaged or dropped into water. Cease use
immediately and contact Kogan.com for support.
• Do not expose this appliance or it’s power cord to fire and other sources of heat.
Caution
• Do not apply excessive force to your teeth or gums.
• When not in use, store this appliance safely to avoid it being damaged or dropped
into water.
• Do not immerse the appliance in water as this may lead to malfunction, cause fire,
electric shock or explosion.
• Do not plug or unplug this appliance with wet hands.
• Ensure that your power outlet voltage corresponds to the voltage stated on the
rating label.
• Do not drag, bend, warp or place heavy object on the power cord as this may
cause damage.
• Grasp the plug when removing the appliance from the power outlet. Never remove
by pulling the power cord.
• Always unplug the appliance before cleaning or performing maintenance.
• Do not expose this appliance to fire, high-temperature or moist environments and
avoid excessive exposure to direct sunlight.
SAFETY & WARNINGS

• Do not charge the appliance in high-temperature or moist environments such as
bathrooms or toilets.
• Always unplug the appliance if it is not being used for an extended period.
Note
• This appliance features non-serviceable parts. If it needs to be repaired, contact
Kogan.com for support.
• Do not use the appliance without a nozzle attached.
• Do not fill the appliance with the mouth wash as this may cause corrosion.
• This appliance can be used by children and persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Cleaning and user maintenance shall not be
made by children without supervision.
• Do not allow children to play with the appliance.
• If you have had any recent dental surgery or procedures, please consult your
physician before using the appliance.

OVERVIEW
Power button
LED indicators
To p c o ve r
Nozzle release button
Nozzle
Body
Charging port
Water tank
Water tank lid

Charging the flosser
1. Plug the power cord into the charging port.
2. Plug the power cord into a power outlet.
3. The charging indicator on the main body will begin blinking.
Note: The water flosser will take approximately 4 hours to fully charge.
4. When the water flosser is fully charged the indicator light will be stop blinking and
remain on.
Nozzle
1. Ensure the appliance is turned off.
2. Insert the nozzle into the hole on the top cover.
3. If need to remove or replace the nozzle, ensure the appliance is off then press the
nozzle release button and remove the nozzle by pulling upwards (Figure 1).
Figure 1
OPERATION

Filling the water flosser
1. Open the water tank lid.
2. Holding the main body horizontally fill the water tank with clean water (Figure 2).
3. Close the water tank lid.
Figure 2
Using the water flosser
1. Press the Power button to begin the flow of water.
2. Holding the water flosser vertically, insert the nozzle into your mouth, aiming the
flow of water at your gums or teeth.
3. Ensure the nozzle is kept parallel to your teeth and gums. Do not aim the nozzle
directly into the periodontal pocket (Figure 3)
4. Keep your mouth slightly open allowing the water to flow out into your sink (Figure
4).
5. The water flosser will automatically turn off after 2 minutes. If you need to continue
using the flosser press the Power button to start the flow of water again.
Figure 4
Figure 3
Note:
Do not fill the water tank with water exceeding 40°C.

Changing flossing modes
The water flosser features four different flossing modes: Normal, Soft 1, Soft 2 and Pulse.
Press the Power button during operation to cycle between the modes.
• Normal: For the normal cleaning of teeth.
• Soft 1: For the users with sensitive teeth.
• Soft 2: For the users with sensitive teeth. This setting is recommended for first time
users.
• Pulse: This mode is used for massaging gums which to help promote blood
circulation and strengthen the teeth.
Emptying the water tank
After usage, the water tank should always be completely emptied.
1. Holding the water flosser horizontally, open the water tank lid and allow the water
to drain out (Figure 5).
2. Press the Power button to ensure no residual water is left in the water tank.
3. Close the water tank lid and wipe the flosser with a dry cloth.
Figure 5
Note:
It is recommended to use the “Soft 2” mode for at least week.
Note:
When not in use the water flosser should be free of residual water to avoid
bacterial infection. If it is not used for an extended period of time, ensure to
clean the water flosser well, then dry and store it.

The water flosser with can be cleaned with water or mild detergent. No not use any
corrosive or abrasive detergent as it will damage the water flosser. Do not clean with water
exceeding 50°C.
Cleaning the body:
• Clean the body with a dry or damp cloth.
• Do not immerse the body in water for cleaning.
Cleaning the water tank
• Wipe the water tank with a dry or damp cloth.
• The water tank can be detached and rinsed with water.
• Ensure the water tank is clean and completely dry if it is not being used for an
extended period.
Cleaning the nozzle
• Wipe the nozzle with a dry or damp cloth.
• The nozzle can be detached and rinsed with water.
• Do not bend, pull or warp the nozzle.
• It is recommended to replace the nozzle every 6 months.
Cleaning the charger
Wipe the metal part of plug with dry cloth every 6 months to avoid dust accumulation which
may result in poor contact.
CLEANING & CARE

Problem
Possible cause
Solution
The water flosser will not turn
on.
The battery is flat.
Charge the water flosser for
at least 24 hours.
The water pressure is low.
The nozzle is blocked.
Replace the nozzle.
The filter is blocked.
Clean the filter.
The water flosser only
operates for a short time after
being charged.
The battery is dead.
Contact Kogan.com.
The water flosser has not
been fully charged.
Charge the water flosser for
at least 24 hours.
The charging indicator does
not illuminate when
charging.
The power cord is not
properly connected.
Check the power cord
connections.
Circuit malfunction.
Contact Kogan.com.
Declaration for hazardous substances
Declaration for Hazardous Substances
Part name
Hazardous Substances
Pb
Hg
Cd
Cr (VI)
PBB
PBDE
PCB
X
O
O
O
O
O
NOTE: “X” means YES; “O” means NO.
Disposal of rechargeable battery
Do not dismantle the water flosser unless it is being discarded. Please unplug the appliance
before removing the battery.
1. Ensure that the battery has been exhausted before removing it. To discharge the
battery, press the Power button to turn on the water flosser and continue to run it
until it stops working. Repeat several times until the battery is completely flat.
2. Remove the water tank and detach the top cover
3. Remove the unit core.
TROUBLESHOOTING