Kogan SMARTERHOME SECURITY CAMERA DOORBELL 3 PRO User manual

KOGAN SMARTERHOME™ SECURITY
CAMERA DOORBELL 3 PRO
KASMDBLATBA

Doorbell
Chime
Screwdriver
User guide
Power adapter
USB cable
Screw (x3)
Wall anchor (x3)
COMPONENTS

Doorbell
Chime
SD card slot
Reset
Speaker
Micro USB
Lens
Motion sensor
Microphone
Micro USB
Status Light
Doorbell button
Speaker
Speaker
Status light
USB Power
interface
Reset
OVERVIEW

Mounting the Doorbell
1. Remove the mounting screw from the bottom of the doorbell with the screwdriver.
2. Separate the doorbell from the mounting bracket.
3. Attach the bracket to the wall using the supplied screws.
4. Replace the doorbell back onto the bracket and secure it with the previously
removed mounting screw.
Note: Depending on the type of wall you are securing to, you may need to use the
included wall anchors as well. If you’re unsure as to what hardware suits your
requirements, please seek advice from a qualified trade professional.
INSTALLATION
Doorbell
Mounting
bracket

Install App
Download the “Kogan SmarterHome” app from the Play Store (Android) or App Store (iOS).
Play Store (Android)
App Store (iOS)
To register:
1. If you already have a SmarterHome account, select ‘Log In’. To register a new
account, select ‘Sign Up’.
2. The system will automatically recognise your country. If needed, you can manually
select your country from the drop-down box. Enter your email address and tap
‘Get Verification Code’ to continue.
3. A 6-digit code will be sent to the submitted email address. Enter this code before
the one-minute timer expires.
4. Continue to the next page and complete your SmarterHome profile.
CONNECT TO SMARTERHOME™ APP

Set device in pairing mode
When the device is first turned on, it may automatically enter pairing mode (indicator is
rapidly flashing BLUE).
If not automatically in pairing mode when powered on, you can manually set the device in
pairing mode by pressing and hold the reset button for 5 seconds until the indicator is
rapidly flashing BLUE.
Add device through network
1. Once registered, tap “Add Device” on the app’s home page, or the “+” in the upper
right corner, to add a new device through the network.
2. Select the product type from the list of options in the app Home Security > Door
Bells).
3. Enter your Wi-Fi details. It is important that your SmarterHome™ device and the
app are connected to the same Wi-Fi network during setup.
Notes:
• The device and the app have to use the same Wi-Fi network.
• The device is only compatible with 2.4Ghz networks.
• Depending on the product, Steps 3 and 4 may be in opposite order.

4. Ensure that the device is in pairing mode, with the indicator rapidly flashing BLUE,
and tap “Next”.
5. The device will commence the pairing process and connect to the app. Ensure
your Wi-Fi router, mobile phone, and the SmarterHome™ device are kept close
until connection is complete.
6. After successfully being added, you will have the option to rename the device and
assign it to a location. It will now be listed on the app’s home page. Tap the device
listing to enter its control page.
Note:
Once connected, you can select Create Scene from the “+” in the upper right
corner (or from the Scene tab) to group connected SmarterHome™ products
and automate their functions.

Adding “SmarterHome” to the Google Home app
1. From the home page of the Google Home app, select the “+” icon (top left corner,
see arrow in the below screenshot) to access the ‘Add and manage’ page.
2. Select ‘Set up device’, then select the ‘Works with Google’ option.
GOOGLE HOME CONTROL
Note:
You will need to have set up a Google Home account prior to linking
your Kogan SmarterHome™ device.

3. Select the search bar and type ‘Smarter Home’ to locate the Kogan
SmarterHome™ service.
4. From here, you will be prompted to sign into your SmarterHome™ account using
either your email or mobile phone number, depending on which method you used
to register your account.
5. Select “Kogan SmarterHome™” from the app options.

6. Tap ‘Authorise’ to grant Google permission to access the SmarterHome™ app and
your devices.
7. Once connected, the app will display any compatible devices linked to your
SmarterHome™ account. From here you can assign them to rooms and set up any
routines. Tap on any of the devices to view a list of available commands.
Note:
Please note that Google Home can only control the base/core functions of any
compatible SmarterHome™ devices. To make full use of this product’s smart
functionality, please use the Kogan SmarterHome™ app.

Adding “SmarterHome” to the Alexa app
1. From the home page of the Alexa app, select the “ ” icon in the bottom-right and
select “Skills & Games” from the sidebar.
2. Select the search bar and type ‘Smarter Home’ to locate the Kogan
SmarterHome™ skill.
AMAZON ALEXA CONTROL
Note:
You will need to have set up an Alexa account prior to linking your Kogan
SmarterHome™ device.

3. Tap ‘Enable to Use’ to add the Kogan SmarterHome™ skill to Alexa.
4. From here, you will be prompted to sign into your SmarterHome™ account using
either your email or mobile phone number, depending on which method you used
to register your account.
5. Select “Kogan SmarterHome™” from the app options.

6. Tap ‘Authorise’ to grant Alexa permission to access the SmarterHome™ app and
your devices.
7. Once connected, the app will perform a search and display the devices linked to
your SmarterHome™ account. When your devices have successfully connected to
the Alexa app, you will be able to control your Kogan SmarterHome™ devices via
Alexa’s voice commands.
Note:
Please note that Alexa can only control the base/core functions of any
compatible SmarterHome™ devices. To make full use of this product’s smart
functionality, please use the Kogan SmarterHome™ app.

1. Attach the Chime to the power adapter.
2. Press the Reset button on the Chime, the indicator will begin flashing BLUE. The
Chime is now pairing mode (searching for connection).
PAIRING CHIME WITH DOORBELL
Note:
The Doorbell and Chime have been paired together from the factory. If they
are not paired, the following steps will help you pair them.
Indicator
Reset

3. In the SmarterHome app open the doorbell settings by tapping the “…” button in
the upper right corner.
4. Tap "Bell Settings".

5. Tap the "Bind" button, the chime will connect to the doorbell. The indicator light
on the chime will turn solid BLUE if successfully paired.
6. Select the ringtone and volume settings, exit back to the Preview screen to
complete the process.
Notes:
If the configuration fails, please press the "RESET" button for 5 seconds to reset your
chime and click the "RESET" button, then add it again.

Two-way audio
When the visitor pushes the doorbell button, you will get a call. You can see and hear the
visitor in your App from the doorbell if you answer.
Motion detection
Motion sensors will notify you when movement is detected.
Shared device
The doorbell can be shared with friends and friends so they can access the camera’s feed.
There is no limit to the number of sharing devices, but only 6 accounts are supported for
online preview at the same time.
Record
Record every moment by using high-capacity SD card storage.
Day & Night
Powerful night vision means no interruptions, even in complete darkness.
Daytime
Night
OPERATION

Doorbell
Power Port
DC 5V/1A of charging; battery (4800mAh)
Doorbell button
Press the button to activate the doorbell
Status light
Solid RED: Network is disabled
Rapidly flashing RED: Wait for network connection
Slowly flashing RED: Connecting the network
Solid BLUE: Camera is working correctly
Microphone
Capture sound for your video
SD card slot
Support local SD Card storage (Max.128G)
Reset
Press and hold on for 5 seconds to reset
Chime
Mini USB
DC5V±10%, USB power supply
Reset
Press the RESET for 5s to restore Factory Settings.
Click the RESET button to pair the doorbell
Status light
Flashing BLUE: Waiting for configuration.
Solid BLUE: Configuration completed
SPECIFICATIONS

Problem
Solution
While connecting to the
Kogan SmarterHome™
app, it never successfully
reaches 100% and
connects.
This doorbell only supports 2.4GHz Wi-Fi router, ensure
you are using a 2.4GHz Wi-Fi router and confirm the Wi-
Fi password again. 5.0GHz connections will not connect.
Multiple repeated
attempts to connect.
After a failed attempt to connect, you may need to
restart the device or power off and then try to add again.
After connecting, the
device does not appear
online, or cannot be
accessed in the app.
Check whether the network is normal, you can place the
camera close to the router and if not, it is recommended
to reset the device and add it again.
Unable to reconnect with
a new router.
First remove and reset the device on the SmarterHome™
app and then configure the device again within the app.
Device still in the list of
devices after resetting?
The reset device only resets the network configuration of
the camera, but cannot change the configuration on the
app. Deleted the doorbell the app.
App not displaying smart
phone notifications.
Ensure that app is running in the background and that
notifications have been activated.
Doorbell not recognising
the SD card.
It is recommended to remove and re-insert an SD card
after a power cut. Confirm whether the SD card is
normally available (try reading it on another device) and
that the format is FAT32.
TROUBLESHOOTING