Kogan KAHCWDAC16A User manual

WINDOW WALL AIR
CONDITIONER
KAHCWDAC16A, KAWDAC26TA & KAWDAC41TA

2
Safety & Warnings
3
Overview
5
Installation
6
Operation
10
Cleaning & Care
13
Specifications
15

3
• Ensure to read all instructions in this user guide prior to first use. Retain this user guide
for future reference. Misuse may cause injuries to people and damage property.
• IMPORTANT: All wiring must comply with local and national electrical codes and must
be installed by a licenced electrician. If you have any questions regarding the following
instructions, contact a licenced electrician.
• Check available power supply and resolve any wiring problems before installing and
operating this unit.
• For your safety and protection, this unit is grounded through the power cord when
plugged into a matching wall outlet. If you are not sure whether your wall outlet is
properly grounded, please consult a qualified electrician.
• The rating plate on the unit contains electrical and other technical data. The rating
plate is located on the right side of the unit. Make sure to use correct power supply
according to the rating plate of your air conditioner.
• WARNING: This air conditioner can be used by children aged from 8 years and above
and persons with reduced physical, sensory, or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
• Do not allow children to play with the air conditioner.
• Cleaning and user maintenance shall not be performed by children without supervision.
• To ensure safety, always switch off and cut the power supply when the air conditioner is
not in use for long time.
• If the power cord is damaged, cease use immediately and contact help.Kogan.com for
support.
• Always switch off and cut the power supply before performing any maintenance or
cleaning. Not doing so may cause electric shock or damage.
• Do not attempt to repair the air conditioner yourself. Incorrect repairs may cause fires or
explosions. Contact a qualified service technician for all service requirements.
• Do not attempt to disassemble the air conditioner yourself.
• Do not use the air conditioner during lightning storms. The power supply should be cut
in time to prevent danger.
• Do not put hands or any objects into the air inlet or air outlet. This may cause personal
injury or damage to the air conditioner.
• Do not use the air conditioner for other purposes, (for example, drying clothes,
preserving foods).
SAFETY & WARNINGS

4
Electric Shock Hazard
The air conditioner has a serial rating voltage. It must have its own fuse or circuit
breaker and no other device or unit should be operated on the fuse or circuit breaker. To
avoid the possibility of personal injury, disconnect power to the unit before installing or
servicing.
Operation
• Check the capacity of wiring and power outlet. Do not use the power outlet with other
appliances connected.
• Ground the air conditioner to prevent danger of electric shock.
• Connect the air conditioner with power source securely. Use the fuse as below.
CAUTION:
• The installation parts must be protected against corrosion, especially in cases
where the air conditioner will be installed near the sea or hot springs.
• Do not install the air conditioner in a place where flammable gas leaks are
possible. Ensure any combustible surfaces and materials are at least 10cm away
from the unit during heating mode.
• The range of external static pressures at which the appliance has been tested is
0- 5Pa.
CAUTION:
• Before installation, turn off the operation switch and disconnect the power cord.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety Children should be
supervised to ensure that they do not play with the appliance.
• The appliance is fitted with means for disconnection from the supply mains,
having a contact separation in all poles that provides full disconnection under
overvoltage category III conditions, and these means must be incorporated in
the fixed wiring in accordance with the wiring rules.

5
OVERVIEW
Front Cover
Air inlet grille
(Indoor)
Cabinet
Air outlet grille
(Indoor)
Air inlet grille
(Outdoor)
Vent Lever
Control Panel
Air filter
Remote Control
Control Panel

6
Location
• Select a location that can support the weight of the air conditioner and will not cause
increased operation noise or vibration.
• Avoid direct sunlight for efficient cooling.
• Select a place where there are no obstructions near the air inlet and outlet.
INSTALLATION
Less than 210
More
than 55
Wall thickness is less than 210
Less than 210
Scrape
If the wall thickness is more than 210,
scrape the wall as shown above.
5-10mm
Make rear side lower so that water
will drain out smoothly.
More than
400
More than
400
More
than 500
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Less than 210

7
Installation instructions
1. Remove the front panel. (Fig.5)
Remove the air filter. (Fig.6)
Remove screws at the bottom of the front panel. (Fig.7)
Open the panel cover.
2. Remove the screws in the chassis-fixing board and cabinet. Some models have
two more screws on the back of the cabinet. (Fig.8)
3. Grasp the handle on the front of the chassis and carefully slide the air conditioner
unit out of the cabinet. (Fig.9)
Fig. 8
Fig. 9

8
4. Install the drain tube connection into the hole provided at the rear of the air
conditioner chassis. (Fig.10) (Available for single drainage method: rear drainage
only).
Bottom drainage: The drain tray is fixed in position using four screws, and the flare
nut is used to block the rear drainage hole. (Fig.11)
Rear drainage: Use the flare nut to block the bottom drainage hole and use a
water outlet pipe to connect the rear drainage hole. Pay attention to the sealing
ring to prevent water leakage. (Fig.12)
5. Install the air conditioner cabinet on the installation shelf (not included) with
screws. (Fig.13)
Fig. 10
Drain tray screw
Flare nut
Flare nut
Sealing ring
Water outlet pipe
Fig. 11
Fig. 12
Wall
Cabinet
Installation shelf
Screw
Fig. 13

9
6. Carefully slide the unit back into the cabinet. (Fig.14)
7. Reinstall the retaining bracket, front panel, and mounting screws. (Fig. 8, 7, 15)
8. Reinstall the air filter. (Fig.16)
Fig. 14
Fig. 15
Fig. 16

10
Control panel buttons
No.
Button
Function
1
Used to adjust airflow direction.
2
• Used to set or cancel timer operation.
• When the unit is in operation, you can set the OFF TIMER.
When the unit is off, you can set the ON TIMER. Timer
setting range is 0 to 24 hours.
• If the OFF TIMER is set, the timer LED displays the
remaining time to turn off the unit for 10 seconds, then the
LED shifts to display set temperature. If you press the
TIMER button within the 10 seconds, the OFF TIMER will be
cancelled.
• If the ON TIMER is set, the timer LED displays the remaining
time to turn on the unit. If you want to cancel ON TIMER,
press the TIMER button.
3
Used to turn the air conditioner ON/OFF.
4
Every time you press this button, the operation mode is
changed in sequence: COOLING/FAN ONLY/HEATING
COOLING.
5
Used to select fan speed in sequence: auto, high, mid, and
low.
6
• This button is used to set room temperature mode or used
to set time in TIMER mode. If the two keys are pressed at
the same time for more than three seconds, the
temperature LED display will alternate between °C and °F.
• Temperature setting range is from 16°C to 31°C.
7
Used to activate the SLEEP function
OPERATION

11
Control panel
The below symbols turn on when the relevant mode is in use.
No.
Button
Function
1
Timer
2
Cooling
3
Heating
4
Fan only
5
Sleep
6
Display set temperature/display set timer
7
Low fan speed
8
Mid fan speed
9
High fan speed
10
Auto fan speed
11
Compressor running

12
Remote control
The remote control transmits signals to the system. The unit will confirm the command with
a beep.
No.
Button
Function
1
(TEMP UP)
Increase the temperature or time by 1 unit
2
(TEMP DOWN)
Decrease the temperature or time by 1 unit
3
ON/OFF
To switch the unit ON/OFF
4
FAN
To select the fan speed of AUTO/LOW/MID/HIGH
5
TIMER
To set automatic switching ON/OFF
6
SLEEP
To activate the SLEEP function
7
MODE
To select the mode of operation
8
SWING
To activate or deactivate movement of the deflectors

13
Air filter
• The air filter should be washed at least once a month. If the air filter remains full of dust,
the air flow will decrease, and the cooling capacity will be reduced.
• The filter is behind the cover and can be pulled out from the right-hand side.
• Wash the air filter with water and mild detergent.
• Rinse with clean water and dry it before reinstalling.
Long off-period maintenance
• Operate the fan alone (“LOW FAN” or “HIGH FAN”) for half a day to dry out the inside of
the unit.
• Tu r n o f f p ow e r a n d r e m ov e p l u g f r o m power outlet.
• After a long off-period and when you are about to use the air conditioner again, clean
the condenser (at the rear) and evaporator (at the front) fins by using a soft brush or
vacuum cleaner.
CAUTION:
• Do not use hot water above 40°C for washing the air filter.
• Let the filter dry thoroughly in the shade before reinstalling. Do not expose
it to direct sunlight.
• Do not operate the air conditioner with the filter removed.
CAUTION: Be careful not to damage the fins during cleaning.
CLEANING & CARE

14
Air cleaning filter
The air cleaning filter is attached to the air filter. Wash the air cleaning filter as well when
washing the air filter.
Front cover
• The front cover will accumulate dirt and dust. To clean it, wipe it with a soft dry cloth.
When it is excessively dirty, wipe it with a soft cloth dampened with warm water or mild
soap and then wipe it again thoroughly with a soft dry cloth.
• Never use hot water above 50°C, benzene, gasoline, acid, thinner or brushes to wipe off
dirt, as they will damage the plastic surface and the coating.

15
Rated volts
250
Amps
3.15
Climate class rating
T1
ambient temperature for cooling: 18~43°C.
ambient temperature for heating: -5~20°C.
T3
ambient temperature for cooling: 25~52°C.
ambient temperature for heating: -5~20°C.
Disposal
• Do not dispose of electrical appliances as unsorted municipal
waste, use separate collection facilities.
• Contact your local government for information regarding the
collection systems available.
• If electrical appliances are disposed of in landfills or dumps,
hazardous substances can leak into the groundwater and get
into the food chain, damaging your health and well-being.
SPECIFICATIONS

16
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com