Kogan SMARTERHOME KAWFHTP15BA User manual

KOGAN SMARTERHOME™
PANEL HEATER
(1500W)
KAWFHTP15BA, KAHTP15WALA

•Read all instructions carefully before use.
•Ensure the voltage supplied matches the requirements indicated on the rating
plate of the heater.
•Do not operate this appliance if the cable or plug has become damaged.
•Keep the appliance and cable away from other sources of heat, sharp objects or
anything else that may cause damage.
•If the cord is damaged, it must be replaced by Kogan.com in order to avoid a
hazard.
•Ensure the appliance is turned off before connecting to the mains power supply.
•Tu r n off the power supply at the switch and remove the plug from the outlet when
the heater is not in use, is being cleaned or undergoing any other maintenance.
•To disconnect the heater, turn it off, then remove the plug from the outlet. Do not
pull on the cord to disconnect the plug.
•The heater must not be located immediately below its power socket.
•Do not operate in areas where fuel, paint or any other flammable liquids are used or
stored.
•This heater is for indoor use only.
•Do not cover the heater. This may cause overheating and/or fire hazard.
•To prevent a possible fire, never block the air intakes or exhaust vents in any
manner.
•Do not touch any hot surfaces directly.
•Do not insert or allow foreign objects to enter into any ventilation or exhaust
openings, as this may cause electric shock, fire or damage to the appliance.
•Always ensure that your hands are dry before operating or adjusting any switches
on the product or touching the plug and socket-outlet.
•This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety.
•The heater is not a toy. Children should be supervised to ensure that they do not
play with the heater.
•Do not leave the heater unattended while it is in use.
•The most common cause of overheating is deposits of dust or fluff in the appliance.
Ensure these deposits are removed regularly by disconnecting the appliance from
the power supply, then vacuum cleaning the air vents and grilles.
SAFETY & WARNINGS

•Do not place the heater on carpet and don’t place the cable under carpets.
Arrange the cord away from traffic areas so that it will not be tripped over.
•Do not use this heater in the immediate surroundings of a bath, a shower or a
swimming pool.
•Do not store away until the heater cools down, store the heater in cool dry location
when not in use.
•The heater must not be used if the glass panel is damaged. Cease use
immediately.
WARNING — KEEP BATTERIES OUT OF REACH OF CHILDREN
•Swallowing may lead to serious injury or death in as little as 2
hours, due to chemical burns and potential perforation of the
oesophagus.
•If you suspect your child has swallowed or inserted a button
battery immediately call the 24-hour Poisons Information
Centre on 13 11 26 (Australia) or 0800 764 766 (New Zealand)
for fast, expert advice.
•Examine devices and make sure the battery compartment Is
correctly secured, e.g. that the screw or other mechanical
fastener is tightened. Do not use if compartment is not secure.
•Dispose of used button batteries immediately and safely. Flat
batteries can still be dangerous.
•Tell others about the risk associated with button batteries and
how to keep their children safe.

1
Heater body
5
Mode button
2
Feet (x2)
6
Timer button
3
Display screen
7
Power button
4
Temperature button
OVERVIEW

Portable Installation
Attach the feet using the supplied screws
(8 x ST4*12mm), screwing each oner into
the heater with a Phillips head screwdriver
(not supplied).
Wall Mounting
•Do not fit with the feet if wall mounting.
•Prepare the bracket with screws (figure 1).
•Using the bracket as a guide for the holes, drill into the wall and insert the plastic
expanded plugs. Attach the bracket to the wall with screws (figure 2).
•Place the heater in a suitable position, ensuing that the holes align with the
bracket (figure 3).
•Tighten screw on the top of bracket to secure (figure 4).
•Ensure the product is securely installed in the correct position and the power
cord is undamaged before its first use.
INSTALLATION

Connect the power cable into a wall outlet, and turn on the power switch on the side of the
heater.
Power Function
Press the Power button to set functions. The upper part of the display will show the room
temperature. The heater will be working at low power heating conditions.
Mode
Press the Mode button to switch between low or high temperature power.
Temperature Selection
Press to select the desired temperature from a range of 15°-35°C. The temperature
indicator will remain lit for a while.
Timer
Press the timer button to select the desired range between 1 hour to 24 hours. The display
will show the remaining time.
OPERATION

Install App
Download the “Kogan SmarterHome” app from the Play Store (Android) or App Store (iOS).
Register
If you do not have a Kogan SmarterHome™ account, register or sign in with a verification
code sent by SMS.
To register:
1. Tap to enter registration page.
2. The system automatically recognises your country/area. You can also select your
country code manually. Enter your email address and tap ‘Next.’
3. Alternatively, you can select ‘Register by mobile number’ and enter the verification
code sent to you by SMS.
4. Create a profile on the next page to define your location and room.
CONNECT TO SMARTERHOME™ APP

Set device in pairing mode
When the device is first turned on, it may automatically enter pairing mode (light on the
display will be flashing rapidly).
If not automatically in pairing mode when powered on, you can manually set the device in
pairing mode by long-pressing the Mode button for 5 seconds until the light on the
display begins flashing rapidly. Alternatively, turn off the power and restart the heater.
Add device through network
5. Once registered, tap “+” in the upper right corner of the app’s home page to add a
new device through the network.
6. Select the product type from the list of options in the app (Heating & Cooling >
Heaters).
7. Ensure that the device is in pairing mode, with the the light on the display flashing
rapidly, and tap “Confirm light is rapidly flashing”.

8. Upon successfully confirming pairing mode, enter your Wi-Fi details. It is important
that your SmarterHome™ device and the app are connected to the same Wi-Fi
network during setup.
9. The device will commence the pairing process and connect to the app. Ensure your
Wi-Fi router, mobile phone, and the SmarterHome™ device are kept close until
connection is complete.
10. After successfully being added, you will have the option to rename the device and
assign it to a location. It will now be listed on the app’s home page. Tap the device
listing to enter its control page.
Notes:
•The device and the app have to use the same Wi-Fi network.
•The device is only compatible with 2.4Ghz networks.

Adding “SmarterHome” to the Google Home app
1. From the home page of the Google Home app, select the “+” icon to access the
‘Add and manage’ page.
2. Select ‘Set up device’, then under the Works with Google banner, select ‘Have
something already set up?’
3. Select the search bar and type ‘Smarter Home’ to locate the Kogan
SmarterHome™ service.
GOOGLE HOME CONTROL
Note:
You will need to have set up a Google Home account prior to linking your
Kogan SmarterHome™ device.

4. Tap ‘Authorise’ to grant Google permission to access the SmarterHome™ app and
your devices.
5. From here, you will be prompted to sign into your SmarterHome™ account using
either your email or mobile phone number, depending on which you registered your
account with.

6. Once connected, the app will display any compatible devices linked to your
SmarterHome™ account. From here you can assign them to rooms and set up any
routines.
7. Tap on any of the devices to view a list of available commands.
Note:
Please note that Google Home can only control the base/core functions of any
compatible SmarterHome™ devices. To make full use of this product’s smart
functionality, please use the Kogan SmarterHome™ app.

Adding “SmarterHome” to the Alexa app
1. From the home page of the Alexa app, select the “ ” icon in the top-right and
select Skills & Games from the sidebar.
2. Select the search bar and type ‘Smarter Home’ to locate the Kogan
SmarterHome™ skill.
AMAZON ALEXA CONTROL
Note:
You will need to have set up an Alexa account prior to linking your Kogan
SmarterHome™ device.

3. Tap ‘Enable to Use’ to add the Kogan SmarterHome™ skill to Alexa.
4. From here, you will be prompted to sign into your SmarterHome™ account using
either your email or mobile phone number, depending on which you registered your
account with.
5. Tap ‘Authorise’ to grant Alexa permission to access the SmarterHome™ app and
your devices.

6. Once connected, the app will perform a search and display the devices linked to
your SmarterHome™ account.
7. When your devices have successfully connected to the Alexa app, you will be able
to control your Kogan SmarterHome™ devices via Alexa’s voice commands.
Note:
Please note that Alexa can only control the base/core functions of any compatible
SmarterHome™ devices. To make full use of this product’s smart functionality,
please use the Kogan SmarterHome™ app.

Dimensions
430 x 240 x 760mm
Weight
4.8kg
Output frequency
50/60Hz
Voltage
220-240V
Wattage
750W / 1500W
Colour
Black, White
Overheat safety protection
Yes
SPECIFICATIONS

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com