Kohler FAMILY CARE K-22781T-1 User manual

FAMILY CARE
INSTALLATION INSTRUCTIONS
VANITY (ROCKER)
K-22781T-1
-1-
·
·
·
Observe all local plumbing and building codes.
Prior to installation, unpack the new lavatory and inspect it
for damage. Return the lavatory to its protective carton
until you are ready to install it.
All information in these instructions are based the latest
product information available at the time of publication.
Kohler China reserves the right to make changes in
product characteristics, packaging, or availability at any
time without notice.
Make sure that the wall and floor are square
and plumb to ensure proper installation.
IMPORTANT:
·
·
·
ORDERING INFORMATION
FAMILY CARE Vanity 1000mm(Rocker)...............K-22781T-1 1000mm ........................................K-22781T-1
REQUIRED MATERIALS/
(NOT SUPPLIED)
TOOLS
·
·
·
·
·
·
·
·
Level
Drill with bit6mm
14mm wrench
Framing square
Channel lock pliers
Tape measure
Pencil
Sealant
·
·
·
·
·
·
·
·
6mm
14mm
©
©
Copyright Kohler China Investment Co., Ltd. 2019
2019
No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137
2 528137
8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA 256410
8 256410
NO.1 KOHLER STREET, ECONOMIC DEVELOPMENT ZONE OF FAKU COUNTY, SHENYANG LIAONING PROVINCE, PRC 110400
1 110400
:
POST CODE:
POST CODE:
1395235-T01-A

-2-
Install the Basin
Note! The lavatory tops must be installed on a cabinet (refer
to Installation and User Guide packed with the cabinet for
installation details).
Recommend Kohler bathroom furniture for support or
decoration.
!
(
)
!
·
76mm
·Rough-in the supplies and the drain piping.
The supply stop handles cannot extend more than
76mm from the finish wall when in the open position.
NOTE:
·
·
10mm
()
65-
75mm
1. 81mm( )
4.
2. 2 3
3. 2 3
·
·
Drill two 10mm hanger bolt holes at the marks on the wall.
The nylon anchors is needed for concrete wall (supplied).
Mount hanger bolts to the wall so approximately 65-75mm
of each bolt remains exposed.
1. The distance from center of vanity drain hole to the
wall is 81mm(see roughing-in), and please choose
P-trap or S-trap according to the position and
dimension of the drain hole and space of the
cabinet.
2. Refer to Fig.2 for P-trap installation and Fig.3 for S-
trap installation. The positions shown are for
reference only, which can be adjusted according to
drain pipe type, cabinet structure and drain layout
of the house.
3. The height in Fig.2 and Fig.3 can be adjusted
according to actual height of the cabinet. Inlet of
hot water and cold water can be adjusted according
to installation conditions.
4. Other fastening devices of sufficient size and
strength may also be used.
NOTE:
K-22781T-1
Fig.#1
1
132
450
81
120
185
Kohler reserves the right to change marked dimensions without prior notice.
ROUGHING-IN
Reference Value UNIT: mm
552
200
610
1000
136
380
85
558
45
35
293
171
1395235-T01-A

-3-
·
33
·Install the faucet, handle and drain to the lavatory
according to the manufacturer s instructions.
The 3 pipes on the handle shall be pulled through the
hole on the lavatory bottom and tightened with the cable tie,
as shown in Fig.3.
Note!
·
·
·
·
·Carefully place the lavatory against the wall, so the
hanger bolts extend through the lavatory holes.
·
·
·
Level the lavatory.
Install the cap nuts and washers, and tighten until snug.
Do not
overtighten the cap nuts.Overtightening may cause
damage to the product.
Clean the lavatory top.
CAUTION: Risk of product damage.
·
·Put the sealant around the back wall attached surface of
the lav evenly.
Apply Silicone sealant
along this face
Washer Nut
Offset Nut
Fig.#5
5
Fig.#4
4
Fig.#2
2
Attachment
Bolt (x2)
Wall Plug
*480mm
Wall Outlet Wall Outlet Trap
*495mm
*825mm
*60mm
200mm
610mm
Fig.#3
3
Attachment
Bolt (x2)
Wall Plug
Floor Outlet
Outlet TrapFloor
*495mm
*825mm
*60mm
80mm
610mm
Handle
Pipe
Pipe Hole
Cable Tie
1395235-T01-A

Take out Deck and place it at the designated place after
installation is finished.
-4-
1.
2.
3.
4.
78mm/81mm(
)
Install the Plumbing
1. Install the drain in accordance with the manufacturer s
instructions.
The distance from center of vanity drain hole to the
wall is 78mm/81mm(see roughing-in), and please choose
suitable drainage pipe.
Make sure a watertight seal exists on all
basin drain connections.
Provide access to the plumbing connections
for future plumbing maintenance.
2. Connect the hot and cold water supplies.
3. Open the hot and cold water valves, and check the supply
connections for leaks.
4. Run water into the basin, and check the drain connections
for leaks.
NOTE:
Caution!
Caution!
,
IMPORTANT CONSUMER INFORMATIONIMPORTANT CONSUMER INFORMATION
CARE AND CLEANING
To keep your lavatory looking new, make sure you rinse it out
thoroughly after each use. on this
product, as they will scratch and ruin the surface. Stubborn
stains, paint, or tar can be removed with turpentine or paint
thinner.
DO NOT USE ABRASIVES
Caution! Risk of product damage.
Many cleaners contain abrasive and chemical substances,
and should not be used for cleaning stainless steel, enamel,
plated or plastic fittings.
These finishes should be cleaned using a mild washing up
detergent or soap solution, rinsed and then wiped dry with a
soft clean cloth.
SERVICE PARTSSERVICE PARTS
1034692
Assy. Pack
1337784
Deck 880089-CP
Operationg Rod
Fig.#6
6
1174906
CABLE TIE, 24"
24"
1395235-T01-A