Kohler URBANITY 15096T User manual

URBANITY
INSTALLATION INSTRUCTIONS
VANITY TOP
K-15095T/K-15096T
-1-
, 2009
Copyright Kohler China Ltd., 2009
·
·
·
Observe all local plumbing and building codes.
Prior to installation, unpack the new lavatory and inspect it
for damage. Return the lavatory to its protective carton
until you are ready to install it.
All information in these instructions are based the latest
product information available at the time of publication.
Kohler China reserves the right to make changes in
product characteristics, packaging, or availability at any
time without notice.
Make sure that the wall and floor are square
and plumb to ensure proper installation.
IMPORTANT:
·
·
·
ORDERING INFORMATION
URBANITY 800mm Vanity........................................K-15095T
URBANITY 1100mm Vanity......................................K-15096T
800mm .............................................K-15095T
1100mm ...........................................K-15096T
528137
REQUIRED MATERIALS/
(NOT SUPPLIED)
TOOLS
·
·
·
·
·
·
·
Level
Drill with bit6mm
14mm wrench
Framing square
Channel lock pliers
Tape measure
Pencil
·
·
·
·
·
·
·
6mm
14mm
ROUGHING-IN
UNIT: mm
:
K-15096T
125 88
174
536
1105
70
35
45
700
130
769
205
454
1130444-T01-A

-2-
Install the Basin
Note! The lavatory tops must be installed on a cabinet or
matching metal stand (refer to Installation and User Guide
packed with the cabinet or stand for installation details).
Recommend Kohler metal square leg or Kohler bathroom
furniture for support or decoration.
!
(
)
!
·
76mm
·Rough-in the supplies and the drain piping.
The supply stop handles cannot extend more than
76mm from the finish wall when in the open position.
NOTE:
·
·
10mm
()
65-
75mm
1. 2 3
2.
·
·
Drill two 10mm hanger bolt holes at the marks on the wall.
The nylon anchors is needed for concrete wall (supplied).
Mount hanger bolts to the wall so approximately 65-75mm
of each bolt remains exposed.
1. Height dimensions marked in fig. 2 and fig. 3 could
be adjusted per your the vanity height or the actual
height of the console leg.
2. Other fastening devices of sufficient size and
strength may also be used.
NOTE:
K-15095T
Fig.#1
1
Attachment
Bolt (x2)
Wall Plug
550mm
Waste
Outlet Waste
630mm
805mm
80mm
769mm
Fig.#2
2
125 165
805
70
35
205
45
380
700
130
454
540
URBANITY 1100mm Vanity
K-15096T
1100mm
K-15096T
1130444-T01-A

-3-
380mm
Attachment
Bolt (x2)
Wall Plug
550mm
Waste
Outlet Waste
630mm
805mm
80mm
·· Install the faucet and drain to the lavatory according to the
manufacture's instructions.
·
·
·
·
·Carefully place the lavatory against the wall, so the
hanger bolts extend through the lavatory holes.
·
·
·
Level the lavatory.
Install the cap nuts and washers, and tighten until snug.
Do not
overtighten the cap nuts.Overtightening may cause
damage to the product.
Clean the lavatory top.
CAUTION: Risk of product damage.
·
·Put the sealant around the back wall attached surface of
the lav evenly.
Fig.#3
3
Apply Silicone sealant
along this face
Washer Nut
Offset Nut
Fig.#4
4
URBANITY 800mm Vanity
K-15095T
800mm
K-15095T
1130444-T01-A

-4-
1.
2.
3.
4.
Install the Plumbing
1. Install the drain in accordance with the manufacturer s
instructions.
Make sure a watertight seal exists on all
basin drain connections.
Provide access to the plumbing connections
for future plumbing maintenance.
2. Connect the hot and cold water supplies.
3. Open the hot and cold water valves, and check the supply
connections for leaks.
4. Run water into the basin, and check the drain connections
for leaks.
Caution!
Caution!
,
Fig.#5
5
IMPORTANT CONSUMER INFORMATIONIMPORTANT CONSUMER INFORMATION
CARE AND CLEANING
To keep your lavatory looking new, make sure you rinse it out
thoroughly after each use. on this
product, as they will scratch and ruin the surface. Stubborn
stains, paint, or tar can be removed with turpentine or paint
thinner.
DO NOT USE ABRASIVES
Caution! Risk of product damage.
Many cleaners contain abrasive and chemical substances,
and should not be used for cleaning stainless steel, enamel,
plated or plastic fittings.
These finishes should be cleaned using a mild washing up
detergent or soap solution, rinsed and then wiped dry with a
soft clean cloth.
1105685-**
Overflow Cover
SERVICE PARTSSERVICE PARTS
1034692
Assy. Pack
1130444-T01-A