Kohler K-23111T User manual

-1-
ORIENTAL
INSTALLATION INSTRUCTIONS
MIX CABINET
K-23111T/K-23113T/K-23112T/K-23114T
BEFORE YOU BEGIN



Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information-please leave instructions for the





consumer.
ORIENTAL bathroom cabinet adopts E1 grade wood-
based panel of high quality, and with further processing,
its harmful emissions will be less than 1.5mg/L.
Turn off the water supply.
The pluming installation must comply with Water Supply
Regulations/Bye-laws, Building Regulations or any
particular regulations and practices, specified by the local
water company or water undertakers. The installation
should be carried out by aplumber.
Before installation carefully inspect the new fixture for any
signs of damage.
This product complies with GB 24977-2010.


 -





E1
1.5mg/L
GB 24977-2010
900mm
600mm ............................K-23111T/K-23113T
............................K-23112T/K-23114T
ORDERING INFORMATION
This installation covers the following products in the
ORIENTAL range:
ORIENTAL 900mm Mix Cabinet........K-23111T/K-23113T
ORIENTAL 600mm Mix Cabinet........K-23112T/K-23114T
SAFETY WARNINGS
Kohler products are precision-engineered and should give
continued superior and safe performance, provided:
1. They are installed, commissioned, operated and
maintained in accordance with the recommendations given
in this Manual.
2. Periodic attention is given, as necessary, to maintain the
1.
2.
©Copyright Kohler China Investment Co., Ltd. 2017
©2017
product in good functional order. Recommended
guidelines are given in the MAINTENANCE section.
Carefully inspect the new fixture for any signs of damage.
When installing Kohler Products, manufacturers guidelines for
power tool safety should be followed.
CHANGSHU KOHLER LTD., SOUTHEAST ECONOMIC DEVELOPMENT ZONE,
CHANGSHU, JIANGSU PROVINCE, CHINA POST CODE 215500
215500
1312558-T01-A

530
770
510
530
770
770
530 510
530
770
770
770
-2-
UNIT :mm
INSTALLATION
A. Install Washbasin Cabinet
Install the services.
Hot (H) and Cold (C) inlets must be connected to the correct
inlet pipes.
Install the drain in accordance with the manufacturer's
instructions.
We suggest using P-trap drain. Connect P-trap pipe with
washbasin drain.
CAUTION !Make sure awatertight seal exisits on all
washbasin drain connections.
CAUTION !Provide access to the plumbing
connections for future plumbing maintenance.
NOTE The hot and cold water supplies must be installed
with isolating valves.
A.
(H) (C)
P
Fig.2
2
ROUGHING-IN
Reference Value
Fig.1
1
Kohler reserves the right to change marked dimensions without prior notice.
K-23111T/K-23113T
900mm Mix Cabinet
900mm
K-23112T/K-23114T
600mm Mix Cabinet
600mm
600
900
600 600
900 900
51
0
510
51
0 51 0
510 510
1312558-T01-A

-3-
1. 3 1. Place the cabinet at adesired position in the bathroom,
and then adjust the four adjustable feet to put the cabinet
in place. (see Fig.3)
8
8
cabinet connects the glass countertop. Place the glass
countertop onto the cabinet and wait for the sealant to dry.
See Fig.5
3. Dismount the washbasin cabinet and put aside. Drill holes
at the marked position.
CAUTION! Avoid the cables and pipes inner set when
drilling in the wall.
NOTE: Different types of bolts are required for different
decoration boards. Please apply suitable bolts and
Plugs.
4. Insert the plugs into the wall.
5. Apply awasher to the screw before tighten it. Make sure
the washbasin cabinet has been fixed firmly on the wall.
6. Evenly apply silicon sealant of high quality to where the
8
Fig.4
4
3.
4.
5.
6. 5
Go up
2. Mark the wall through two holes at the corresponding
positions. As Fig 4.
Go up
Go down
Fig.3
3
2.
Go down
4
1312558-T01-A

B. Finish Installation
1.
2.
3.
4.
a. (P
1. Install the faucet and lavatory in accordance with the
manufacturer's instructions.
2. Connect the hot and cold water supplies.
3. Attach the waste, and tighten securely.
4. Turn on the hot and cold water valves and check the
supply connections for any leaks.
a. Inwall drainage (P-Trap)
Please install the drain assembly and faucet as shown.
Please set the water supply and drainage position
according to the suppliers instructions.
Apply Silicone Sealant
Apply Silicone Sealant Apply Silicone Sealant
Apply Silicone Sealant
Fig.6
6
-4-
,
)
/
Faucet
Lavatory
Supply Lines
Shut-off Valve
Drain Assembly
Note: Handle the glass countertop
gently and evenly. Avoid collision
or friction with hard objects.
Fig.5
5
B
1312558-T01-A

b. S
b. Floor drainage (S-Trap)
Please install the drain assembly and faucet as shown.
Please set the water supply and drainage position
according to the suppliers instructions. You can adjust the
height of shelf to fit the drain assembly.
-5-
Fig.7
7
8
Rail
Step 1
1
Step1
1
NOTE For installation of cabinet, please first remove the
drawers and reinstall them onto rails after fixing the drainage
(see Fig.8).
Step2
2
Step2
2
Step 1
1
Fig.8
8
5.
, 9
6.
7.
5. Run water into the washbasin or vanity top, and check the
drain connections for any leaks.
6. Adjust all hinges of door in three-way as illustrated in Fig 9,
and make sure that the door is level and neat. Clearance
between doors is even, and that between doors and
cabinet is tight.
7. Place the hinge cover and plastic cover.
Outlet
Faucet
Lavatory
Supply Lines
Shut-off Valve
Drain Assembly
Ripple Pipe
1312558-T01-A

DAILY MAINTENANCE
WARNING! Risk of product damage.
1. Many cleansers contain abrasive and chemical substance
which is not suitable for cleaning stainless steel, enamel,
plating or plastic products. You may use mild cleansers or
soaps to clean the surfaces. Wipe any splashes of cleaner
solutions from the surface with clean soft cloth.
2. Maintain ventilation in the bathroom, and separate the dry
area from the damp one if conditions permit. Try to open
the door and windows of the bathroom and maintain good
ventilation.
3. Kohler bathroom cabinet are dealt with strict procedures
for damp-proof, whose good damp-proof function ensures
good performance even in bathroom of huge humidity. Yet
do not splash and pour water directly on the bathroom
cabinet. Make sure that the bathroom is not over damp
and wipe any splashes from surfaces immediately.
4. Maintenance of door board: Clean and wipe door board
regularly, and wipe the condensation vapor with dry and
soft cloth. Keep PVC doors away from fire or high
temperature.
5. Avoid scratching the glass surface with sharp-pointed
objects.
6. Please do not sit, lean or step on the basin cabinet.
7. If any fixtures caused by abnormal reasons, Kohler China
can supply paid replacement for service parts caused by
abnormal reasons in the limited duration of warranty.
-6-
Fig.9
9
1.
2.
3.
4.
5.
6.
7.
1312558-T01-A