Kohler Englefield Valencia Elite User manual

1223207-A02-G September 2023 englefield.co.nz
Page1
VALENCIA / VALENCIA ELITE
DOUBLE DRAWER VANITY
FURNITURE |
Floor Standing Models
Wall Hung Models
® ®

BEFORE YOU BEGIN:
ROUGH-IN:
Please read these instructions carefully to familiarise yourself with the required tools, materials, and
installation sequences. Follow the sections that pertain to your particular installation. This will help you
avoid costly mistakes. In addition to proper installation, read all operating and safety instructions.
Prior to installation, inspect the cabinet and vanity top (either Durastone top, ceramic top or stone
quartz top) to ensure that no damage has occurred in transit. If damage has occurred, or a visible defect
exists, do not proceed with installation, and advise your supplier immediately.
Instructions, drawings, and diagrams contained in this manual present information available at the time
of printing.
Although every attempt has been made to keep them up-to-date, Englefield reserves the right to implement
product changes without further notice.
Floor Standing Models
Wall Hanging Models
850 800 467
605 755
650 600
905 1205 1205
englefield.co.nz
Page2
NOTE: For rough-in dimensions and installation instructions of the Valencia Elite Stone
vanity tops, please refer to the supplementrary guide supplied with the stone quartz tops.
1223207-A02-G September 2023
Please leave these instructions for the consumer. They contain important information.
INSTALLATION INSTRUCTIONS
VALENCIA Double Drawer Vanity
/
VALENCIA ELITE
®®

1. Drawer removal
Floor standing models must be fixed to a nog in the wall. Wall hung models must be fixed to two nogs
in the wall. The nog size should be 50 x 75mm.
(a) Open the drawer and carefully lift up on the
end of the drawer to release it from the runner
locator pins. It may be necessary to gently pry
the runner away from the drawer.
(b) The drawer is now only held by the runner
hooks at the back and can be pulled out in
the direction shown.
CONSTRUCTION REQUIREMENTS:
INSTALLATION:
TOOLS AND MATERIALS REQUIRED - (Not Supplied)
Floor standing models
To suit pipework To suit screws
TOOLS MATERIALS - Not supplied & must be purchased separately
Fixing washers
20mm
Screws (Refer step 3)
10g x 75mm
50
Locator pin
A height of 800 to 850mm
from the floor to the top of the
vanity top is recommended for
the wall hung vanity.
50mm from top of
cabinet to centre
of nog.
50mm from top of
cabinet to centre
of nog.
Wall Hung models
50
Positioning of the nog near
vertical centre is recommended
however exact position will
depend on plumbing etc.
800-850
Runner hook
www.englefield.co.nz
Page3
1223207-A02-G September 2023
INSTALLATION INSTRUCTIONS
VALENCIA Double Drawer Vanity
/
VALENCIA ELITE
®®

Alternate drain
position for floor
standing models
2. Water supply and waste pipe holes
(a) Measure and mark the centres for water
supply and waste pipes on the back of the
cabinet.
(c) Having drilled the required holes fit the cabinet
into position over the pipework.
NOTE: Before fastening the cabinet make sure that
the it is sitting level and square and if installing a
floor mounted model ensure that the selected
location is free of bumps and protrusions.
NOTE: Screws should be positioned in an evenly
spaced pattern as shown below.
Mounting brackets screw positioning
Floor standing models
Wall Hung models
Screw positions
for 600mm floor
mount vanity shown
Screw positions
for 600mm wall
mount vanity shown
50
50
200
50
100100
50
50
50
Floor standing models
Wall Hung models
50
50
50
50
Mounting bracket
Mounting
bracket
(b) With a suitably sized hole saw drill the holes
for the water supply and waste.
englefield.co.nz
Page4
1223207-A02-G September 2023
INSTALLATION INSTRUCTIONS
VALENCIA Double Drawer Vanity
/
VALENCIA ELITE
®®

Size Floor Mount
Number of screws required
600 3
750 4
Wall Mount
900 4
1200 5
5
7
7
9
3. Fixing the vanity to the wall
(a) Fix the cabinet to the wall using screws (min
10g x 75mm) and *20mm washers. Screw
through the back rail or wall so that they screw
into the nog/s in the wall behind.
*Washers must be used to spread the load.
(a) Unpack the top and check for any damage that
might have occurred in transit. Check and
confirm the fit of your selected tapware.
(b) Apply a continuous bead of silicone (not
supplied) to the top edge of the cabinet sides
and back. Ensure there are no gaps in the
sealant bead. This will ensure the top stays
securely fitted to the cabinet and no water
spillage will find its way into the cabinet.
No silicone on
front edge
(a) To re-install the drawers, extend the runners.
Place a drawer onto the runners and slide back
so that the runner hooks insert into the rear of
the drawer.
(b) Make sure the locator pins line up with the
holes in the bottom of the drawer and press the
drawer down so that the pins slot into place.
6. Drawer re-installation
Runner hook
Locator pin
5. Waste and tapware
(c) Place the vanity top onto the cabinet ensuring
that the back is flush against the wall and
there is an even overhang on either side of the
cabinet.
(d) Wipe off any excess sealant.
(a) Fit the waste and tapware. Connect the water
supply to the taps and waste pipe to the waste
outlet.
(b) Run hot and cold water and check for leaks.
When satisfied with the results move on to the
next section.
= =
englefield.co.nz
4. Vanity top
Page5
INSTALLATION INSTRUCTIONS
1223207-A02-G September 2023
*Mount Screws will
need to unscrewed
before removing the
drawer for latest
runners setup.
VALENCIA Double Drawer Vanity
/
VALENCIA ELITE
®®

7. Drawer Height Adjustment
Runner hook
englefield.co.nz
5 Vanity top
(a) Unpack the top and check for any damage that
might have occured in transit. Check and
confirm the fit of your selected tapware.
(b) Apply a continuous bead of silicone (not
supplied) to the top edge of the cabinet sides
and back. Ensure there are no gaps in the
sealant bead. This will ensure the top stays
securely fitted to the cabinet and no water
spillage will find its way into the cabinet.
No silicone on
front edge
(a) To re-install the drawers, extend the runners.
Place a drawer onto the runners and slide back
so that the runner hooks insert into the rear of
the drawer.
(b) Make sure the locator pins line up with the
holes in the bottom of the drawer and press the
drawer down so that the pins slot into place.
= =
7 Drawer re-installation
(a) All edges MUST be sealed with an approved
Silicone Sealant.
- Between cabinet and floor
- Bewteen cabinet and wall
- Between upstand and wall
8 Sealing
VALENCIA
TM
Vanity
6 Waste and tapware
(c) Place the vanity top onto the cabinet ensuring
that the back is flush against the wall and
there is an even overhang on either side of the
cabinet.
(d) Wipe off any excess sealant.
(a) Fit the waste and tapware. Connect the water
supply to the taps and waste pipe to the waste
outlet.
(b) Run hot and cold water and check for leaks.
When satisfied with the results move on to the
next section.
(a) All edges MUST be sealed with an approved
Silicone Sealant.
- Between cabinet and floor
- Bewteen cabinet and wall
- Between upstand and wall
8. Sealing
INSTALLATION COMPLETE
(a) Remove the drawer. To tilt the drawer front
forward before adjusting the height of drawer.
(b) Turn anticlockwise on the locator pin spacer to
raise the height of the drawer and turn clockwise
to raise down. Repeat on the other runner.
(c) For 77296 A-*: Re-install the cabinet door.
Hook the hinges onto the base plates and press
down as shown.
Note: All drawers are aligned during assembly.
However further adjustment is often required after
installation.
Please ensure the cabinet has not been twisted
and installed correctly before adjusting.
Page6
INSTALLATION INSTRUCTIONS
Height Adjustment Front Sectional
View
UP
DOWN
1223207-A02-G September 2023
Hook
VALENCIA Double Drawer Vanity
/
VALENCIA ELITE
®®

Page7
1223207-A02-G September 2023
INSTALLATION INSTRUCTIONS
CLEANING AND MAINTENANCE INSTRUCTIONS
For cleaning instructions, please refer to the Owner’s Information Leaflet.
englefield.co.nz
(a) To re-install the drawers, extend the runners.
Place a drawer onto the runners and slide back
so that the runner hooks insert into the rear of
the drawer.
(b) Make sure the locator pins line up with the
holes in the bottom of the drawer and press the
drawer down so that the pins slot into place.
7 Drawer re-installation
(a) All edges MUST be sealed with an approved
Silicone Sealant.
- Between cabinet and floor
- Bewteen cabinet and wall
- Between upstand and wall
8 Sealing
INSTALLATION COMPLETE
Runner hook
Locator pin
INSTALLATION INSTRUCTIONS
ENGLEFIELD
CONTACT AND WARRANTY INFORMATION
NEW ZEALAND
Kohler New Zealand Limited
0800 100 382
AUSTRALIA
englefield.com
info@englefield.co.nz
englefield.co.nz
VALENCIA Double Drawer Vanity
/
VALENCIA ELITE
®®
Compression moulded vanity top:
To clean use non abrasive soap and water. It is recommended that the product surface is
wiped dry after each use to prevent the build up of soap and scum.
Vanity cabinet:
The materials used in the vanity cabinet are water resistant only, not water proof.
Care must be taken to clean up all water spillage onto the vanity cabinet surfaces.
To maintain the finish on your vanity cabinet clean with mild soapy water and dry with a soft
cloth.
WARNING
FOR YOUR PERSONAL SAFETY AND PRODUCT DURABILITY,
ENSURE THAT HOT WATER SUPPLY IS REGULATED TO 55°C MAXIMUM
CAUTION
Material used in cabinet is water resistant only, not waterproof.
Care must be taken to clean up all water spillage.