Kohler K-72441T User manual

-1-
INSTALLATION INSTRUCTIONS
MIRRORED CABINET
K-72441T
BE BOX
, 2013
Copyright Kohler China Ltd., 2013
13-1 528437
BEFORE YOU BEGINBEFORE YOU BEGIN
·
·
·
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation . This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information-
Before installation carefully inspect the new fixture for any
signs of damage.
Be
careful when opening the door to avoid pinching
fingers.
Don't use acidic or alkalic cleaners or
alcohol to clean the surface. Use a dampened cloth to
clean.
please leave instructions for the
consumer.
WARNING: Risk of injury or product damage.
WARNING:
·
·
·
·
-
PARTS
Parts supplied with your cabinet. (For cabinet body and door
replacement, call customer service with model number.) Be
sure to check the cardboard supports in the carton, glass
parts are packed in them.
Tips:
1. When opening or closing the door
leftwards or rightwards, please grasp the
door at the lower right corner or lower left
corner to avoid pinching fingers.
2. Recommended installation height: 1.2m
from the floor.
1.
2. 1.2
Grasp Position
Installation height
1.2m from floor
1.2
1208162-T01-A

-2-
ACCESSORIES LISTACCESSORIES LIST
Screws ST3.5 35
ST3.5 35
X5
Hinder
X2
1170223
Base Cup Shelf
X1
Wall Anchors
X5
1124095
Snap-in Pins
X18
Caps of Screw
X8
Wheel Cover
X4
Top Clips
X2
1169355
Cup
X1
Glass Shelves
L=137mm
X2
Glass Shelve with Hole
L-354mm
X1
Glass Shelve with Hole
L-354mm
X1
ROUGHING-IN
UNIT : mm
Kohler reserves the right to change marked dimensions without prior notice.
Reference Value 370
680
543
900
115
75
96
1208162-T01-A

-3-
INSTALLATION
Cabinet Installation
STEP
1
STEP
2
1.
56
1. Drill installation holes:
Drill five 6 holes of the following dimensions. Make sure
holes in the same row are at the same level.
Fix the mounting bar to the
wall, level the mounting bar.
Drill holes
4- 6mm
4- 6mm
Drill holes
4- 6mm
4- 6mm
500
558.5
295
295
Screws ST3.5 35
and Wall Anchors
ST3.5 35
Distance from highest point of the countertop (such as faucet handle) 40
()40
500
5- 6
6
295
590
558.5
1208162-T01-A

STEP
3
STEP
4
2. Install the mounting bar
3. Fixing the cabinet
a. Put the cabinet on the mounting bar.
b. Slide top clips to align with the holes drilled in the
previous step. Fix with screws.
2.
3.
a.
b.
-4-
Top Clip
Cabinet
Mounting Bar
1208162-T01-A

-5-
Installation of Slide Door Assy.
STEP
1
STEP
2
1.
a.
b.
1.
a. Loosen the screws of the top and bottom wheels with
screw driver.
b. Lift each wheel and put into the rail slot.
Make sure each wheel is properly put into the rail
slot.
Note:
1208162-T01-A

Installation of Service Parts
STEP
1
STEP
3
2.
a. Tighten the screws of the top and bottom wheels with
screw driver. The wheels must be pressed tight onto
the rail slot.
b. Slide the door leftwards and rightwards. When the door
is firmly fixed onto the cabinet and slides smoothly,
please tighten the nut of the screw.
c. If the door is not straight, please adjust by tightening or
loosening the adjustable screws to align the door with
the cabinet side frame.
1. Press the snap-in pins into the holes on the vertical
frames.
2. Press down the glass shelf tight onto the snap-in pins.
3. Put the cup on the glass shelf with holes.
2.
a.
b.
c.
1.
2.
3.
-6-
Screw
Nut
Snap-in Pin
B
A
1208162-T01-A

STEP
2
4. Put the top cover into the slot on top of the cabinet (Note:
If installed with lighting of Kohler brand, the power of the
lighting can be installed as shown in the picture and then
fix the top cover. Lighting is not supplied with the cabinet.)
5. Fix the wheel cover onto the wheel assembly (align the
slot of the wheel cover with the L-shaped iron sheet of the
wheel assembly and the press tight.)
4. (
)
5. (
L)
-7-
Top Cover
Power of
Lighting
(Not Supplied)
()
Wheel Cover
Wheel Cover (Slot)
()
Wheel Assembly (L-shaped Iron Sheet)
(L )
1208162-T01-A