Kohler 24270T-CP User manual

All information is based on the latest product information
available at the time of publication, Kohler Co. reserves
the right to make changes in product characteristics,
packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They
contain important information.
所有的资料是按最新出版的产品资料编写而成。
科勒公司保留任何时候不经通知即可改变产品特
性、包装或产品可供类型的权利。
说明书包括重要的安装、保养及清洁方面的内容，
请把这些资料交给用户阅读。
1. Flush the water supply pipes thoroughly to remove debris.
Faucet is designed for tap water or potable water.
2. Do not attack the faucet with rough strength to avoid
being damaged.
3. Do not damage the surface of sensing window when
installing or cleaning the faucet.
4. For new installations, install the faucet and drain to the
lavatory before installing the lavatory.
5.As for DC type faucets, please pay special attention to
insert direction match of battery poles. Tighten the battery
cover completely to prevent its exposure to moisture.
6. As for AC type faucets, strictly follow indicated instructions
to perform electric connection. Only provide electric supply
to power box after the installation is completed.
1. 一定要先彻底冲洗供水管以清除管道中的杂
质，使用水源为自来水或可供饮用水。
2.请勿将强力及冲击施于产品，以免造成故障，
引起漏水。
3.安装、清洁龙头时，切勿损伤感应窗口表面，
以免造成故障。
4.如果是安装新的洗面盆，可将水龙头和排水组
件先安装好到面盆上。
5. 对于直流龙头， 安装时注意电池的正负极不
能装反，电池盒盖要拧紧，防止电池受潮。
6. 对于交流龙头，安装时务必按照说明书的要
求正确连接导线，龙头安装完毕后才可向电源盒
供电。
Oblo Sensor Faucet
安装之前
Notes:
BEFORE YOU BEGIN
注意事项
安装说明书
欧宝
BLO
7. 修理面盆时，用黑色电工胶布粘住感应窗口。
7.. Cover the sensing window with black tape wh
8. 维修交流龙头时，必须断开交流电源并关闭
repairing lavatories.
水源。
8.. Turn off the electrical source and shut down wat
supplybeforethefaucetsrepaired.
24270T-CP
24271T-CP
24270T-S3-CP
24270T-S5-CP
OBLO DM SENSOR FCT-COLD,W/O P,0.5G,SP
欧宝台盆感应龙头,单冷,不含电源盒,1.9升,特供版
OBLO DM SENSOR FCT-MIXER,W/O P,0.5G,SP
欧宝台盆感应龙头,冷热,不含电源盒,1.9升,特供版
OBLO DM SENSOR FCT-COLD,W/O P,0.35G,SP
欧宝台盆感应龙头,单冷,不含电源盒,1.4升,特供版
OBLO DM SENSOR FCT-COLD,W/O P,0.26G,SP
欧宝台盆感应龙头,单冷,不含电源盒,1.0升,特供版
科勒（中国）投资有限公司
中国上海市静安区江场三路158号 邮编：200436
制造商：上海科勒电子科技有限公司
中国上海市宝山区丰翔路1955号 邮编：200444
1364728-T01-A
1

1. 手伸到出水口下方感应范围
内（感应距离随面盆、周围的情
况而自动调节），水龙头出水。
手离，0.5～2秒后，水龙头自动
止水。
1. Put your hand in the sensing -range, the
faucet should turn on. The faucet should turn
off after removal within 0.5~2 seconds. The
sensing distance will be adjusted automatically
as per the condition of the lavatory and
surrounding environment.
使用说明 OPERATION INSTRUCTIONS
2. 冷热混水龙头水温调节：先关
闭热水角阀，再将冷水角阀旋至
冷水最大状态，再缓慢打开热水
角阀，以免烫伤。如冷水水压
大，打开全部热水角阀后，仍无
合适水温，请再缓慢减少冷水出
水量，直至水温使用舒适。
2. Adjust the water temp for faucet with
temperature mixture: turn off hot water valve
first, and then turn on the water and adjust to
full cold, slowly turn on hot water valve to
avoid scalding. If cold water pressure is high
and unable to gain proper comfortable water
temp even hot water valve is fully open, turn
down cold water capacity slowly until water
temp is comfortable for use.
2
1364728-T01-A
注意：
请勿将龙头安装在台面上，
同时搭配台上盆。
Note:
please do not install the faucet on the
table and match the washbasin

排水组件
φ41.2
φ54
φ31.75
226
φ66.5
72
54
16305T-NA
AC/DC Transformer
(need to buy
separately)交流电源盒
Output: DC6V
输出:直流电压6V
Input: AC220V
输入:交流电压220V
安装尺寸 ROUGH-IN DIMENSIONS
24270T-CP
欧宝台盆感应龙头
（单冷型不含电源盒）
24270T-CP
欧宝台盆感应龙头
（单冷型不含电源盒）
The Drain
24271T-CP
欧宝台盆感应龙头
（冷热混合型不含电源盒）
205 205
136 136
The Top of Lavtory
台盆顶面
The Top of Lavtory
台盆顶面
用户自备角阀
G1/2 外螺纹
Please let user prepare external
thread stop valve G1/2
用户自备角阀
G1/2 外螺纹
Please let user prepare external
thread stop valve G1/2
AC/DC Transformer
(need to buy separately)
交流电源盒
（需另购）
1364728-T01-A
3
205
136
The Top of Lavtory
台盆顶面
47
84
24484T-NA
DC Power Unit
直流电源盒
直流电压6V
Output: DC6V
注：直流或交流电源盒需另购。 NOTE:DC Power or AC/DC transformer need purchasing.

骤步装安 INSTALLATION
一 如何安装水龙头
1.龙头与面盆的安装固定
将固定螺杆(2)安装到水龙头底部(3)
处。再把垫片(4)套在固定螺杆上。并
嵌入水龙头底部的盘槽中。然后将电
源线(8)和进水软管(9)穿过安装孔，
从面盆下方将固定橡胶垫片(5)固定金
属垫片(6)和固定螺母(7)对齐固定螺
杆(2)向上套入。调整水龙头电源线
(8)及进水软管(9)的位置。用扳手拧
紧固定螺母(7)以便把水龙头固定在面
盆上。
How to Install the Faucet
1. Fixing the faucet and lavatory
Install the mounting stud (2) to the bottom
of the faucet (3), then slip the washer (4)
over the mounting stud and put them into
the groove on the spout. Insert the power
wire (8) and supply hose (9) into the hole
from underside of the lavatory. From
underside of the lavatory, slide the rubber
washer (5), meter washer (6) and fixed
nut (7) onto the mounting stud (2).
Tighten nut (7) to make faucet installed on
the lavatory.
技术参数 PARAMETERS
二 安装阀体组件
关闭角阀(12)，
对于冷热混水型的阀体组件安装是先
将三通进水软管组件的两端与角阀
(12)连接，然后把阀体组件(10)进水
口处的保护帽旋出，将阀体组件(10)
进水口与三通进水软管组件(11)连
接；对于单冷型的阀体组件安装是把
阀体组件(10)进水口处的保护帽旋
出，将主阀体组件(10)进水口与角阀
(12)连接。
2. Install alve Assemly
Turn valve off (12).
For mixing water valve assembly
installation, connect water inlet hose
assembly to both ends of stop valve (12),
then unscrew valve assembly (10) water
inlet protection cap, connect valve
assembly (10) inlet to Tee water inlet
hose assembly (11); for cold water faucet
installation, unscrew valve assembly (10)
water inlet protection cap, connect valve
assembly (10) inlet to valve (12).
9
10
11
12
9
10
12
4
1364728-T01-A
2
3
5
4
7
6
8
约1.9L/min
0.35GPM 约1.4L/min
0.26GPM 约1.0L/min
超时用水控制：超时用水1分钟，自动止水。
环境温度：
1～55℃
进水温度：0.5～71℃
适用水压：0.05～
0.86MPa
流量： 0.5GPM
电源：直流 4节5号碱性电池(LR06×4)
交流 电压220V,频率50/60Hz
检测时间：小于0.75秒
关阀延时：0.5～2秒
感应距离：自动调节 0.5GPM About 1.9L/min
0.35GPM About 1.4L/min
0.26GPM About 1.0L/min
Overtime Flowing Control: Automatically stop flushing when
the faucet senses an object for more than 1 minute
continuously
Ambient Temperature: 1~55℃
Supply Water Temperature: 0.5~71℃
Supply Water Pressure: 0.05~0.86MPa
Flow Rate:
Power: DC 4 pieces of AA size alkaline batteries
AC 220V, 50/60Hz
Senser Duration: Less than 0.75s
Shut-off Delay: 0.5~2s
Sensing Distance: Automatic adjustment

四 如何安装排水组件
旋下排水器盘片(15)，在其底面沿
周围涂上一圈密封油灰。把排水
本体(16)由底下插入面盆。
How to Install the Drain
Screw off the drain flange (15) from drain.
Apply a ring of plumbers putty around
underside of the drain flange(15) . Insert
the drain body(16) into the lavatory from
the underside.
15
16
15
16
17
把尾管(18)接上存水弯(19)，尾管需
插入存水弯25mm到55mm之间。
Connect the tailpiece(18) to the trap(19).
The tailpiece should extend 25mm to
55mm into the trap.
18
19
Thread the drain flange (15) onto the drain
Body (16). Tighten the locknut (17) by hand
from the underside of the fixture. Remove
any excess putty.
Note: Do not try to change the position of
the drain after the locknut(17) is tightened,
or you may break the putty seal.
把排水器盘片(15)旋入排水本体
(16)。从下方用手拧紧锁紧螺母
(17)，去除多余的油灰。
注意： 在锁紧螺母(17)拧紧后，不
可再调整排水本体的位置，否则将
会破坏油灰密封。
Apply plumbers putty
涂油灰
1.
14
2.
1. 取出电池盒组件，旋松螺钉
(13)，按电池盒盖(14)上的正负极
标示装入4节5号电池，紧锁电池
盒盖(14)的螺钉(13)后。
注意：电池极性不能装反，新旧
电池不能混用。
2. 在合适的位置打孔，打入膨胀管，
用自攻螺钉固定电池盒。将相同颜
色接插件分别连接。
注意：接插件位置朝上。
14
134
13
14
三 安装电池组件
1364728-T01-A
5

如何安装交流电源盒
AC/DC transformer
交流电源盒
一个交流电源盒供一个感应龙头
接220V交流电
Connect AC 220V
Switch
开关
Wire Tube
穿线管
Wire connection pattern for one to one
Faucet
感应龙头
HOW TO INSTALL THE AC/DC
TRANSFORMER (ONLY USED
WITH TOUCHLESS FAUCET, AC)
(仅限于交流感应龙头)
Connect to
electrical Source
接交流电源
注意：禁止将交流AC220V接入直流DC接线端。
Connect to
Faucet
接感应龙头
Connect to
electrical Source
接交流电源
Connect to
Faucet
接感应龙头
Note: Not allowed connect AC 220V electrical source to DC wire connector of AC/DC transformer
注：交流电源盒需另购。 Note: AC/DC transformer need to buy separately.
6
1364728-T01-A

1. Install AC power unit (sticker on the back) dry, andavoid
showering, soaking from water. Customer prepare wire
tube and wire according to requirement. Wire tube
should be put into the wall. Suggested wire: AC connection
wire should with insulated protecting layer or sleeve and
the section should be bigger than 0.5mm . The section of
DC connection wire should be bigger than 0.3mm . The
connection pattern must according to illustrations above.
2. After wire layout finished, check and repair if needed.
Then connect AC connector of AC/DC transformer to
electrical source from the control box, and DC connector of
AC/DC transformer to faucet. Turn on AC electrical power,
Faucet will commence auto-sense mode which will take
30s. The faucet will not work this period.
直流连接线采用导体标称截面积 mm 的电线。
请严格按照上图进行连接。
0.3
1.电源盒 (背面有不干胶)应安装在干燥，不会被水
淋湿、浸泡的位置。根据需要客户自备穿线管及
连接线。穿线管安装在墙内。建议交流电源线采用
带绝缘和护套层的电线，导体标称截面积 0.5mm ;
2. 排线完毕后，应检查并确保所有排、接线无误，
2
2
2
2
再分别连接电源盒AC接线端与排线管内交流接线
端，以及电源盒DC接线端（黑橙线接头）与龙头
的电源线接插件（从阀盒内引出的电线），最后
打开AC电源，龙头进入30秒自动调距阶段，此过
程龙头不会出水。
1364728-T01-A
7

如何转换成恒温阀感应龙头
(若用户另购 恒温阀16294T-3-CP,
具体安装详见其说明书 )
墙面
Wall
接感应龙头
Connect Sensor Faucet
角阀
Stop Valve 三通
Tee
出水口
Outlet
恒温阀
thermostatic valve
进热水
hot
进冷水
cold
注：软管、三通、角阀请用户自备。
角阀
Stop Valve
三通
Tee
三通
Tee
墙面
Wall
HOW TO CHANGE TO THERMOSTATIC
SENSOR FAUCET (If users buy the
thermostatic valve 16294T-3-CP, the
installation refer to the manual of
16294T-3-CP)
注：软管、三通请用户自备。
三通进水软管组件
Tee, Inlet Assy.
用户自备角阀G1/2外螺纹
Please prepare external
thread angle valve G1/2
Note: Please let users prepare the hose and tee by themselves.
MIN 50mm
Note: Please let users prepare the hose、tee and check
Valve by themselves.
8
1364728-T01-A
HOW TO CHANGE TO A MIXING
SENSOR FAUCET (If customerpurchases
tee inlet assy 1284583-SP)
如何转换成混水感应龙头
(若用户另购三通进水软
管组件1284583-SP)
建议使用科勒推荐的三通进水软管
组件，否则有冷热水互窜的风险。
It is recommended to use Kohler TEE inlet hose assembly,
otherwise there is a risk of cold and hot water mixing problem.

All Finishes: Clean the finish with a mild soap and warm
water. Wipe entire surface completely dry with a clean soft
cloth. Many cleaners may contain chemicals, such as
ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets
and fittings.
CLEANING INSTRUCTIONS
有腐蚀性的清洁剂或溶剂不可使用于科勒的水龙
头及其配件上。
适用于所有加工处理过的表面，以中性肥皂水清
洗镀层表面，再以干净的软布彻底擦干整个表面。
许多清洁剂，比如氨水，去污粉及洁厕灵等，会
对电镀表面造成伤害，切忌使用。
安装结果检查
检查并确保所有衔接处都已拧紧，打开排水系统
和主要供水源，检查并修理有漏水的接口。
Check and ensure that all connections are tight. Open the
drain. Turn on main water supply and check for leaks.
Replace as required.
INSTALLATION CHECKOUT
用户须知
1. 感应指示灯的各种闪烁情况
(3) 间隔2秒钟连续闪烁：若直流感应龙
头, 代表龙头电池耗尽，已停止工作，等
待使用者更换电池;若交流感应龙头，表
示为两种情况：一种为刚刚停电；另一
种为在交流供电正常的情况下，则电源
盒直流接线端接触不良。
(4) 在正常工作情况下，当有物体被感应
时，龙头出水，感应指示灯闪烁一次。
（龙头关闭，感 应指示灯不闪烁。）
IMPORTANT CONSUMER INFORMATION
1. Note of the Indicator Flashing
The indicator is the only and effective way to learn
the faucet's working conditions. So the users can
use the sensor faucet correctly with knowing the
meaning of the sensor indicator's flashing.
(1) Quick flashing means the faucet is in the
period of adjusting sensing distance after power
on for 30s. During these 30s, please do not
disturb auto adjustment or place objects within the
sensing range.
(2) The indicator flashes every 6 seconds (DC
type) indicates that the unit is out of battery and
has stopped working. Replease batteries.
(3) The indicator flashes every 2s: as for DC type
faucets, this indicates the unit is out of battery
and ceases working. Please replace batteries.
For AC faucet, it indicates two possibilities: one
is that the unit is out of battery; or poor DC
terminal contact under normal AC power supply.
(4) In normal condition, the water will flow and
the indicator will flash one time when objects are
inducted. (The indicator does not flash when
faucet stops flowing.)
清理说明
指示灯
2. 超时出水控制
连续在感应状态下使用约一分钟，龙头自动止水。
自动止水后，手或物体离开感应范围后，再次进
入感应范围内，龙头正常工作，否则无反应。
2. Overtime Flowing Control
When the faucet works for about 1 minute continuously, the
water will be shut off automatically. After that, objects must
be removed from the sensing range. Then the water will
flow when objects go into the sensing range again.
Otherwise, the faucet will not work.
感应指示灯是使用者了解感应龙头有效、
唯一的途径。所以明白了感应指示灯闪烁
所代表的含义，可以正确使用感应龙头，
如图示:
(1) 快速闪烁，代表感应龙头正处于通电
后的30秒自动调节阶段。期间，安装者、
使用者不得干扰其自动调节，感应范围
内不要放置物体。
(2) 间隔6秒钟闪烁一次（直流版本），
表示电池即将使用完，请更换电池。
Indicator Light
1364728-T01-A
9

3.清洗过滤系统 3.Clean the Filtration System
The faucet includes connector assembly with high quality
filtration system. If there is a lot of debris in the supply pipes
or the quality of water is bad, it will cause the flow in bad
condition. Please clean th filtration system as following steps:
(1) Close the angle valve.
(2) Remove the valve assembly and take out the filter for
cleaning, then re-install it.
Notice: Make sure to install the filter washer after cleaning
the filter
该感应龙头的阀体组件内已包含了优良的过滤装
置。如管内杂质过多或水质较差，长期使用会引
起出水情况不良。请按以下步骤清洗过滤装置：
(1) 关闭角阀。
(2) 将主阀体组件取下，拿出滤网，用水冲洗完
毕后，重新装入。
注意：在清洗完滤网后，不要遗失平垫。
4.自动清洗存水功能 4. Self-Cleaning the stagnant water
When the faucet is no used for a long period of time, it will
automatically flush to discharge the stagnant water inside
the faucet every 24hrs.
感应龙头长期处于不使用状态时，每间隔24小
时自动冲水一段时间排出龙头内的存水。
10
1364728-T01-A