Kohler K-10349 Assembly instructions

Installation and Care Guide
Heated Seat with Nightlight
Français, page“ Français-1”
Español, pagina “Español-1”
1347697-2-A

Before You Begin
WARNING: Risk of electric shock, fire, or personal injury.
Connect only to a nominal 120 VAC, 60 Hz circuit protected
by a minimum 15 A Ground-Fault Circuit-Interrupter (GFCI)
or Residual Current Device (RCD).
WARNING: Risk of electric shock. Do not immerse or flush
the product with water.
WARNING: Risk of product damage. Liquids can damage
electronic components. Avoid spraying, soaking, or
immersing the seat hinge.
IMPORTANT! This product cannot be installed to a skirted toilet.
The seat mounting holes on the toilet must be accessible from the
underside of the bowl to accommodate the toilet seat cord.
NOTICE: Do not use an extension cord with this product.
NOTE: The features for this product can be controlled from a
mobile device. Download the PureWarmth App and follow the App
instructions.
Observe all local electrical and building codes.
Install an electrical outlet within 4’ (1219 mm) of the toilet.
1347697-2-A 2 Kohler Co.

1. Install the Mounting Plate
Route the cord through the mounting hole on the toilet.
Position the mounting plate over the mounting holes.
Position the washers in the mounting plate with the ″+″oriented
toward the toilet tank.
Insert the bolts through the mounting plate and into the
mounting holes.
Washer
Kohler Co. 3 1347697-2-A

2. Secure the Mounting Plate
Attach the slotted nut onto the cord and slide up on the bolt.
Slide the other nut up on the other bolt.
Using the provided combination tool, tighten the bolts while
holding the nuts in place.
Slotted
Nut
Combination
Tool
Nut
1347697-2-A 4 Kohler Co.

3. Install the Seat
Align the holes in the seat hinge over the posts on the mounting
plate.
Press the seat down to click in place.
Seat Removal
Lift the lid and seat to the vertical position.
Press the side buttons and lift the seat off the mounting plate.
Seat Adjustment (If Needed)
Remove the seat from the mounting plate.
Loosen the bolts, and rotate the washers.
Retighten the bolts.
Reinstall the seat to the mounting plate.
Kohler Co. 5 1347697-2-A

4. Complete the Installation
WARNING: Risk of electric shock, fire, or personal injury.
Connect only to a nominal 120 VAC, 60 Hz circuit protected
by a minimum 15 A Ground-Fault Circuit-Interrupter (GFCI)
or Residual Current Device (RCD).
If not already installed, install an electrical outlet within 4’ (1219
mm) of the toilet.
Thread the power supply cord onto the toilet seat cord. Tighten
the barrel.
Plug the power supply into the electrical outlet.
To begin using this product, refer to the quick start guide.
Care and Cleaning
For best results, keep the following in mind when caring for your
KOHLER product:
IMPORTANT! Do not immerse product in water.
•Always test your cleaning solution on an inconspicuous area
before applying to the entire surface.
•Use a soft, dampened sponge or cloth to wipe surfaces clean.
Remove the cleaner quickly after applying. Rinse and dry any
overspray that lands on nearby surfaces.
•Do not allow cleaners to soak on surfaces.
1347697-2-A 6 Kohler Co.

Care and Cleaning (cont.)
•Never use an abrasive material such as a brush or scouring pad
to clean surfaces.
For detailed cleaning information and products to consider, visit
kohler.com/clean. To order Care & Cleaning information, call
1-800-456-4537.
Range and Function Disclaimer
BLUETOOTH
®
is the name for a short-range radio frequency (RF)
technology that operates at 2.4 GHz. The effective range of most
BLUETOOTH mobile devices is 10 meters. BLUETOOTH is designed
for very low power use. The compatibility of the BLUETOOTH
amplifier interface to mobile/portable devices differs according to the
various individual devices and, in particular, may vary with different
software versions for a device. The normal mobile device
BLUETOOTH range can be up to 10 meters, however, placement of
your mobile device and the BLUETOOTH amplifier’s installation
environment will impact your reception range.
Water and walls can act as blocking agents to the BLUETOOTH signal
that your mobile device is using to broadcast to your BLUETOOTH
amplifier. Therefore, selecting an installation location that removes
these range blocking obstacles will increase the effective range and
performance of your BLUETOOTH amplifier.
You can test your BLUETOOTH reception by performing simple range
tests using your mobile device prior to performing a permanent
installation. The best way to make use of the short BLUETOOTH range
is to make sure your BLUETOOTH amplifier is as close to the
BLUETOOTH transmitter (mobile phone, tablet, etc.) as possible. The
less distance between the two devices, the greater will be the reliability
of your BLUETOOTH audio signal, and the less distance means less
obstacles in the medium through which the transmission is passing, so
there is a reduced chance of audio signal loss.
The compatibility of the BLUETOOTH amplifier to mobile/portable
devices differs according to the various individual devices and, in
particular, may vary with different software versions for a device. All
functions are based on industry-wide communications standards.
Compatibility between the BLUETOOTH amplifier and mobile device
is therefore largely dependent upon the software version of the mobile
device. Other factors (e.g. installation location, walls, distance) mean
that in individual cases, sporadic impairment of functions may occur in
devices that otherwise function reliably. Not all functions are
supported in all countries.
Kohler Co. 7 1347697-2-A

Range and Function Disclaimer (cont.)
Because of these reasons, Kohler Co. can assume no guarantee for the
unlimited compatibility and functionality of your mobile device in
conjunction with the BLUETOOTH amplifier.
_________________________________________________________________
The BLUETOOTH
®
word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by Kohler
Co. approved suppliers is under license. Other trademarks and trade
names are those of their respective owners.
Compliance
FCC ID: N82-KOHLER023
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.
1347697-2-A 8 Kohler Co.

Compliance (cont.)
RF Exposure Warning
This portable transmitter with its antenna complies with FCC’s RF
exposure limits for general population/uncontrolled exposure.
This device must not be co-located or operated in conjunction with any
other antenna or transmitter.
CANADA IC: 4554A-KOHLER023
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
Warranty
ONE-YEAR LIMITED WARRANTY
KOHLER plumbing products are warranted to be free of defects in
material and workmanship for one year from date of installation.
Kohler Co. will, at its election, repair, replace or make appropriate
adjustment where Kohler Co. inspection discloses any such defects
occurring in normal usage within one (1) year after installation. Kohler
Co. is not responsible for removal or installation costs. Use of in-tank
toilet cleaners will void the warranty.
To obtain warranty service contact Kohler Co. either through your
Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing
Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler,
WI 53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from
within the USA and Canada, and 001-800-456-4537 from within Mexico,
or visit www.kohler.com within the USA, www.ca.kohler.com from
within Canada, or www.mx.kohler.com in Mexico.
IMPLIED WARRANTIES INCLUDING THAT OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE
DURATION OF THIS WARRANTY. KOHLER CO. AND/OR
SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states/provinces do not
allow limitations on how long an implied warranty lasts, or the
exclusion or limitation of special, incidental or consequential damages,
Kohler Co. 9 1347697-2-A

Warranty (cont.)
so these limitations and exclusions may not apply to you. This
warranty gives you specific legal rights. You may also have other
rights which vary from state/province to state/province.
This is Kohler Co.’s exclusive written warranty.
1347697-2-A 10 Kohler Co.