Kohler Kumin K-104K37-SANA-CP User manual

1561532-2-A
Installation Instructions
Record your model number:
Noter le numéro de modèle:
Anote su número de modelo:
Français, page 19
Español, página 37
Electronic Bathroom Sink Faucet

Thank You for Choosing KOHLER
Need help? Contact our Customer Care Center.
• USA/Canada: 1-800-4KOHLER (1-800-456-4537) Mexico: 001-800-456-4537
•Service parts: kohler.com/serviceparts
•Care and cleaning: kohler.com/clean
•Patents: kohlercompany.com/patents
Warranty
This product is covered under the KOHLER® One-Year Limited Warranty, found at
kohler.com/warranty. For a hardcopy of warranty terms, contact the Customer Care
Center.
1561532-2-A2 Kohler Co.

Tools
Plumbers Puy Sealant Tape 1/8" Drill Bit 1-1/4" to 1-1/2" Hole Bit
3/8" Supply Stop
Kohler Co. 3 1561532-2-A

Before You Begin
CAUTION: Risk of property damage. Do not use lithium ion baeries with
this product. Exposing lithium ion baeries to water can result in a re.
Follow all local plumbing and building codes.
Turn OFF the water supplies.
This faucet is for a single-hole bathroom sink.
For new installations, install the faucet and drain to the sink before installing the sink.
The faucet shown in this guide may dier from your actual product. The installation
steps still apply.
For installation with a mixing valve, two 3/8" compression supply hoses are required.
1561532-2-A4 Kohler Co.

1. Install the Faucet
Cables
Nut
Metal Washer
Threaded Stud
Rubber Washer
Gasket
Spout
Sensor
Water Inlet Tubing
NOTE: Before drilling the mounting hole, use the following dimensions for proper
placement:
Dimensional Requirements
Mounting Hole: 1-1/4" (32 mm) minimum to 1-1/2" (38 mm) maximum diameter.
Spout to Wall: 1-3/4" (44 mm) minimum distance between the back of the spout
and the wall.
Spout to Sink: 1-1/8" (29 mm) maximum distance between the spout base and the
edge of the sink bowl.
Install the Faucet
Determine the mounting-hole location.
Drill a hole through the mounting surface according to the surface manufacturer’s
instructions.
Install the stud to the boom of the faucet.
Install the gasket to the boom of the faucet.
Insert the faucet, water inlet tubing, and cables through the mounting hole.
Verify that the gasket is in between the escutcheon and the sink/deck surface.
Kohler Co. 5 1561532-2-A

From under the sink, install the rubber washer and metal washer onto the stud.
Thread the nut onto the stud until the faucet is secure.
1561532-2-A6 Kohler Co.

2. Install the Control Box
G1/2 Inlet
Filter
Screen
Mounting Holes
NOTE: Verify that the ex hose can be connected to the supply stop and the control
box inlet before aaching the control box to the wall.
NOTE: Refer to the Specication Sheet to determine the control box installation
location.
Position the control box below the deck and mark the locations for the mounting
holes.
Verify that the sensor cable is below the countertop.
Drill 1/8" (3 mm) pilot holes.
Use the standard wall anchors (provided) depending on your wall material.
Aach the control box to the wall with the arrow pointing upward. Secure with
the two screws (provided).
Unthread the control box screws to remove the cover.
Kohler Co. 7 1561532-2-A

3. Connect the Control Box
Valve
Box
3-Pin
Sensor
cable
Solenoid
Cable
3-Pin
Sensor
Cable
2-Pin
Sensor
Cable
Spout
Wires
2-Pin
Sensor
cable
2-Pin
Power
Connector
2-Pin Power Molex
Connector to
Battery/AC/Hybrid
Battery
2-Pin
Solenoid
Connector
DC-DC Booster Assembly
2-Pin Power
Connector
to control box
Slots
IMPORTANT! The control box and cover have slots for the sensor cables. Use care
not to pinch the sensor cables when installing the cover.
Connect the 2-pin power connector (white) from the DC-DC booster assembly to
the 2-pin power connector (white) of the control box.
Connect the 3-pin sensor cable from the valve cover to the 3-pin sensor cable from
the spout (red, white, and green cables).
Connect the 2-pin sensor cable from the valve cover to the 2-pin sensor cable from
the spout (orange and black cables).
Guide the sensor cables through the slots in the control box.
Loosely secure the cover to the control box for future access.
1561532-2-A8 Kohler Co.

4. Connect the Supplies
Outlet
Inlet
Flex Hose Tube
From Spout
Supply Stop
Flex Hose
Inlet Connections
Connect the ex hose to the supply stop.
Place a bucket under the supply stop and turn ON the water supply.
Slowly open the supply stop to ush debris.
Turn OFF the water.
Connect the provided ex hose from the supply stop to the control box.
Outlet Connections
Verify that the tube from the spout is the appropriate length to reach the control
box. Cut the tube if necessary. Remove any burrs and sharp edges.
Insert the tube into the ing (control box outlet end) until the tube stops.
Verify that the tube is secure.
Kohler Co. 9 1561532-2-A

5. Install the Mixing Valve (If Included)
Outlet
Hot Cold
Lock Screw
3/8" Compression
Adjustment plate to
set water temperature.
Flex
Hose
3/8"
G1/2
3/8"
If a mixing valve is included with your product, connect the ex hoses as shown.
Aach the provided ex hose to the control box inlet and the outlet of the mixing
valve.
Use a 3/8" compression connection (not provided) to aach the cold supply to the
cold inlet on the mixing valve (marked cold on the adjustment plate).
Use a 3/8" compression connection (not provided) to aach the hot supply to the
hot inlet on the mixing valve (marked hot on the adjustment plate).
Temperature Adjustment
Loosen the lock screw on the adjustment plate.
Rotate the adjustment plate to adjust the temperature.
Retighten the lock screw.
1561532-2-A10 Kohler Co.