Konica Minolta PC-410 User manual

E-1
PC-410 Paper Feed Cabinet
INSTALLATION MANUAL
A2XM-9557-00
Applied Machines: C554e/C454e/C364e/C284e/C224e/C554/C454/C364/C284/C224/C368/C308/554e/454e/364e/
284e/224e
COLOR MFP: 55 ppm/45 ppm/36 ppm/30 ppm/28 ppm/22 ppm
MFP: 55 ppm/45 ppm/36 ppm/28 ppm/22 ppm
Product Code: A5AY/A5C0/A5C1/A5C2/A5C4/A2XK/A4FJ/A161/A4FK/A4FM/A7PU/A7PY/A61D/A61E/A61F/A61G/
A61H
Caution:
Lifting the machine in an awkward position or
transporting it in a poorly balanced position could
result in personal injury. When transporting the
machine, assign an adequate number of persons
to the job and ensure that each person can take a
good position of not being excessively loaded
(mass: approx. 23 kg (50-11/16 lb)).
1. Accessory parts
Note:
This manual provides the illustrations of the acces-
sory parts and machine that may be slightly differ-
ent in shape from yours. In that case, instead of
the illustrations, use the appearance of your
machine to follow the installation procedure. This
does not cause any significant change or problem
with the procedure.
Caution:
When removing the paper feed cabinet from its
shipping carton, do not hold the reinforcement
bracket (as a personal injury or a deformed frame
could result).
No. Name Shape Q’ty
1. Leg assy
4
2. Fixing
bracket A 3
3. Fixing
bracket B 1
4. Screw
5
5. Installation
manual 1
set
Keep this bag away from babies and
children. Do not use in cribs, beds,
carriages, or playpens.
The thin film may cling to nose and
mouth and prevent breathing. This bag is
not a toy.
Reinforcement bracket

E-2
2. Installation procedures
(1) Turn OFF the power switch and unplug the
power cord from the power outlet.
(2) Remove the protective tape from the paper feed
cabinet.
Note:
Do not peel the tape that fixes the paper feed cab-
inet hookup harness in position until the machine
is attached to the paper feed cabinet.
(3) Slide the drawer out.
(4) Remove the shipping materials and protective
tape from the inside of the drawer.
Note:
Remove the protective tape A carefully to prevent
the part from being removed together.
(5) Slide the drawer back in.
(6) Remove the connector cover if it is attached to
the machine. (One screw)
Hookup harness
A

E-3
(7) Holding the transportation handles at the right
and left of the machine, place the machine onto
the paper feed cabinet. When placing the
machine, use the positioning pins in the paper
feed cabinet to align the machine correctly with
the cabinet.
Note:
• When transporting or moving the machines,
assign adequate number of persons.
• When attaching the machine, as the reference,
fit the machine with the corner A and B of the
paper feed cabinet.
.
(8) Peel the tape that fixes the paper feed cabinet
hookup harness in position.
(9) Connect the two connectors of the paper feed
cabinet hookup harness to the machine.
(10) Secure the paper feed cabinet to the machine
by the two fixing brackets A.
(Two supplied screws)
(11) Reinstall the connector cover which has been
removed in step (6). (One screw)
When holding the transportation handles,
be careful not to catch your fingers in the
machine.
B
A
Use the fixing brackets to secure the unit
to the machine.
Failure to do so and an unlikely event of
leakage could result in an electrical
shock.

E-4
(12) Slide out the drawer from the paper feed cabi-
net.
(13) Slide out the second drawer from the paper
feed cabinet.
(14) Secure the paper feed cabinet to the machine
by the fixing bracket A (left) and the fixing
bracket B (right).
Fixing bracket A: one supplied screw
Fixing bracket B: two supplied screws
Note:
The fixing bracket B can be placed upside down.
(15) Slide the drawers back in.
(16) Move the machine and paper feed cabinet to
the installation site. Then, adjust the two adjust-
ers at the front to let the paper feed cabinet sit
on the floor.
(17) Attach the four stabilizers (supplied leg assies)
as shown in the illustration.
Note:
• If you proceed to install the Large Capacity Unit
LU-302/LU-301/LU-204 after this installation,
do not attach the stabilizer to the left and right
side of the machine.
• If you proceed to install the Finisher FS-535/
FS-534SD/FS-534 after this installation, do not
attach the stabilizer to the left side of the
machine.
<front and left>
To reduce the risk of injury due to
unstable equipment, set stabilizers
before use.

E-5
<right and rear>
• When removing the stabilizer to move the
machine or for other reasons, pull it out while
pushing the lever shown in the illustration.
<Loading paper>
(1) Slide the drawer out.
(2) Align the edges of the paper stack and place the
stack into the drawer.
Note:
• Make sure that the top level of the paper stack
does not exceed the ▼(MAX) paper level indi-
cator.
• Correct any curl in the paper before loading.
(3) Align the edges of the paper stack and place the
stack into the drawer.
Note:
Make sure that the top level of the paper stack
does not exceed the ▼(MAX) paper level indica-
tor.
(4) Slide the drawer back in.
Lever

E-6
3. Configuration procedures
<Making settings for paper size>
(1) Plug the power cord into the power outlet and
turn ON the power switch.
(2) Display the Service Mode screen (For details of
how to display the Service Mode screen, see the
Service Manual).
(3) Touch “System 2.”
(4) Touch “LCT Paper Size Setting.”
(5) Select the size of paper that was loaded in the
paper feed cabinet.
(6) Touch “END.”
4. Adjustment procedures
<Checking the paper reference position>
<Centering>
(1) Touch “Machine.”
(2) Touch “Printer Area.”
(3) Touch “Printer Image Centering Side 1.”
(4) Touch “3rd.” and then press the Start key.
A test print will be produced.
Note:
• If you proceed to install the Finisher FS-535/
FS-534SD/FS-534 after this installation, move
to the section, <If you install Finisher FS-535/
FS-534SD/FS-534 after this installation>, on
page E-7.
• If you do not proceed to install the Finisher FS-
535/FS-534SD/FS-534 after this installation,
follow the steps below.
(5) Measure width A of the test pattern on the back-
side of the test print produced and check to see if
it falls within the specified range.
Specifications: 3.0 mm ± 1.0 mm
• Adjusting the paper reference position
If the measured width A falls outside the speci-
fied range, enter the correction value using the
or key.
(6) Produce another test print and check to see if
width A falls within the specified range.
Note:
If the use of the or key does not allow the
measurement to fall within the specified range,
perform the following steps.
(7) Slide the drawer out.
(8) Loosen the six screws of the drawer (Left: tow
screws, Right: four screws) shown in the illustra-
tion.
(9) Move the front cover assy while looking at the
tick marks on the scales placed near the screws.
• If the width A is greater than the specifications:
Move the front cover assy to the ➀direction.
• If the width A is smaller than the specifications:
Move the front cover assy to the ➁direction.
(10) Tighten the six screws which have been loos-
ened in step (8).
(11) Produce another test print and check to see if
width A falls within the specified range.
Note:
• Make the adjustment until width A falls within
the specified range.
• Proceed to <Centering (Duplex 2nd side)>
Paper exit
direction
A
Screws
Screws
Scale Scale
➁
➀

E-7
<If you install Finisher FS-535/FS-534SD/FS-534
after this installation>
(5) Measure width A of the test pattern on the back-
side of the test print produced and check to see if
it falls within the specified range.
Specifications: 3.0 mm ± 1.0 mm
• Adjusting paper reference position
(Coarse adjustment)
Make this adjustment if the measured width A
falls greatly outside the specified range.
(6) Slide the drawer out from the paper feed cabinet.
(7) Loosen the six screws of the drawer (Left: tow
screws, Right: four screws) shown in the illustra-
tion.
(8) Move the front cover assy while looking at the
tick marks on the scales placed near the screws.
• If the width A is greater than the specifications:
Move the front cover assy to the ➀direction.
• If the width A is smaller than the specifications:
Move the front cover assy to the ➁direction.
(9) Tighten the six screws which have been loos-
ened in step (7).
(10) Produce another test print and check to see if
width A falls within the specified range.
Note:
Make the adjustment until width A falls within the
specified range.
• Adjusting paper reference position (Fine adjust-
ment)
If the measured width A falls slightly outside the
specified range, enter the correction value
using the or key.
(11) Produce another test print and check to see if
width A falls within the specified range.
Note:
Make the adjustment until width A falls within the
specified range.
Paper exit
direction
A
Screws
Screws
➁
➀
Scale Scale

E-8
<Centering (Duplex 2nd side)>
(1) Touch “Prt. Image Center. Side 2 (Dup).”
(2) Touch “3rd.” and then press the Start key.
A test print will then be produced.
(3) Measure width A of the test pattern on the back-
side of the test print produced and check to see if
it falls within the specified range.
Specifications: 3.0 mm ± 1.0 mm
• Adjusting the paper reference position
If the measured width A falls outside the speci-
fied range, enter the correction value using the
or key.
(4) Produce another test print and check to see if
width A falls within the specified range.
(5) Touch “END.”
(6) Touch “Exit” on the Service Mode screen.
(7) Turn OFF and ON the power switch.
Note:
When displayed the Service Mode screen, be sure
to turn off the power after exiting the Service Mode
screen and wait for 10 seconds or more before
turning on.
Paper exit
direction
A