Konica Minolta ViZion DR+ 1417V2 Use and care manual

1
ViZion DR+
1417V2
Wireless
Panel
Calibration
Manual

[ViZion DR+ 1417V2 Wireless Panel Calibration Manual]
[Ultra 4.2.9.0]
2
Customer Support
1.800.366.5343 –
[email protected]
Table of Contents
Revision History......................................................................................................................... 3
Introduction................................................................................................................................ 4
Hardware Overview and Installation........................................................................................... 5
1ViZion DR+ 1417V2 Wireless Panel Hardware ................................................................... 5
1.1 Passive Installation...................................................................................................... 5
1.2 Integrated Installation................................................................................................... 5
1.3 ViZion DR+ 1417V2 Wireless Panel Detector (Mars1417V2)....................................... 6
1.4 ViZion DR+ Wireless Panel Battery Charger................................................................ 7
1.5 Additional Components................................................................................................ 8
1.6 Mobile Hardware Installation........................................................................................ 8
1.7 Mobile Network Configuration...................................................................................... 9
2ViZion DR+ 1417V2 Wireless Panel Hardware ..................................................................10
2.1 Panel Calibration ........................................................................................................10
2.2 iDetector Interface.......................................................................................................11

[ViZion DR+ 1417V2 Wireless Panel Calibration Manual]
[Ultra 4.2.9.0]
3
Customer Support
1.800.366.5343 –
[email protected]
Revision History
REV DATE DOCUMENT NAME [REASON FOR CHANGE]
1.0 7/17/2018 ViZion DR+ 1417V2 Wireless Panel Calibration Manual
[New Manual –iRay SDK Version 2 and Ultra version 4.2.9.0]
Distributed by:
Konica Minolta Healthcare Americas, Inc.
2217 US Highway 70 East
Garner, NC 27529
1-800-366-5343

4
Customer Support
1.800.366.5343 –
[email protected]
Introduction
This documentation is provided to you, the service technician, with all information necessary to install,
configure and calibrate the ViZion DR+ 1417V2 Wireless Panel. For more detailed information on the
operation and specifications of your wireless detector, please review the following documentation:
Manual References:
• 059-201-04 Mars1417V2 User Manual A0.pdf
Only qualified service personnel should attempt
to install, modify, service or operate the ViZion
DR+ Wireless Panel detector.

5
Customer Support
1.800.366.5343 –
[email protected]
Hardware Overview and Installation
1 ViZion DR+ 1417V2 Wireless
Panel Hardware
The following equipment is required to properly
install and implement your ViZion DR+ system.
1.1 Passive Installation
•ViZion DR+ 1417V2 Wireless Panel
Detector
•ASUS Dual-Band Wi-Fi Gigabit AP
•75 ft. Cat5 Ethernet Cable
•Acquisition PC Desktop or Laptop
(Windows 10)
1.2 Integrated Installation
The following additional equipment is required
for integration with a generator.
•G.I.P.S. Box
•Power Supply Synchronization Cable
•50 ft. Female-to-Female Serial Cable
•Tripp Lite USB-to-Serial Adapter

[ViZion DR+ 1417V2 Wireless Panel Calibration Manual]
[Ultra 4.2.9.0]
6
Customer Support
1.800.366.5343 –
[email protected]
1.3 ViZion DR+ 1417V2 Wireless
Panel Detector (Mars1417V2)
The following equipment is required for
integration with a generator.
1.3.1 Connector Ports and Control Panel
A. DC Jack: 24V DC input
B. Ethernet interface: Link cable jack
C. LED indicators: Indicates the state of the
detector
D. Power button: Detector power ON/OFF
button
E. Infrared window: Infrared device sensor
F. Antenna: Wi-Fi antennas (three)
G. Reserved
H. Maintenance cover: For service engineer to
maintenance
I. Battery lock: The lock button for detaching
battery
J. Detector label: Serial number and product
information
1.3.2 LED Indicators
1. Battery Indicator:
• Green: battery charge is < 10%
• Orange: battery charge is ≥ 10%
2. Link Indicator:
• Blue (solid): wireless connection is
connected
• Blue (blinking): wireless connection is
ready, but not connected
• Green (solid): wired connection is
connected
• Green (blinking): panel initialization
3. Status Indicator:
• Green (solid): data transmission
• Orange (solid): panel initialization
• Orange (blinking): fatal error

[ViZion DR+ 1417V2 Wireless Panel Calibration Manual]
[Ultra 4.2.9.0]
7
Customer Support
1.800.366.5343 –
[email protected]
1.4 ViZion DR+ Wireless Panel
Battery Charger
A. Battery interface: 8-pin battery connector
B. Capacity indicator: Charged capacity
percentage of inserted battery from ≤ 30%
up to 100% (Figure 9)
C. Power indicator: Green light displays when
power is on
D. Hand pull position
E. Limit ball plug
F. DC Jack (24V DC input)
1.4.1 Battery Charger Capacity Indicators
1.4.2 Connector Ports
It is alternatively possible to trickle charge the
battery inside the panel, by connecting the DC
power cable from the DC medical adapter
power supply to the DC input of the detector.
To preconfigure the panel for alternate wireless
connection modes and panel calibration,
connect the Link cable to the mini-HDMI
ethernet interface of the detector for a wired
network connection.

[ViZion DR+ 1417V2 Wireless Panel Calibration Manual]
[Ultra 4.2.9.0]
8
Customer Support
1.800.366.5343 –
[email protected]
1.5 Additional Components
•Battery Pack (2)
•DC Medical Adapter for Detector and
Battery Charger
•AC Power Cable
•DC Power Cable
•Link Cable
•TP-Link AC750 Wireless Travel Router
Access Point (option for mobile)
•ASUS Dual-Band Wireless USB Adapter
(option for mobile)
1.6 Mobile Hardware Installation
Additional required equipment for a mobile
environment.
1.6.1 SourceRay SR-130 Mobile X-Ray Unit
•Side view
•Console view
1.6.2 SourceRay SR-130 Accessory Cables
•Hand Switch.
•Grounded Power Cable.

[ViZion DR+ 1417V2 Wireless Panel Calibration Manual]
[Ultra 4.2.9.0]
9
Customer Support
1.800.366.5343 –
[email protected]
1.7 Mobile Network Configuration
For mobile environments, the panel can be put
into Client mode (to connect the laptop to an
external access point device, that the panel will
connect to [recommended method]), or put in
AP mode (to allow the panel to broadcast a
wireless network, for the laptop to connect to
[alternative method).
1.7.1 ViZion DR+ 1417V2 Wireless Panel in
Client Mode (Recommended method)
When the panel is in Client mode, the panel
will connect automatically to the external TP-
Link Access Point, using the laptop’s LAN
Ethernet adapter. For your internet connection,
you will connect to any available Wi-Fi network
using the laptop’s internal wireless adapter.
Equipment required for Client mode:
•TP-Link AC750 Wireless Travel Router
Access Point
•Link Cable (to preconfigure the panel’s
wireless settings)
To connect the preconfigured TP-Link AP to the
laptop:
1. Unpack the TP-Link AC750 AP (model
TL-WR902AC).
2. Make sure the mode switch on the
side of the access point is set to
AP/Rng Ext/Client.
3. Connect the supplied USB cable
from the laptop to the access point
(supplies power to the device when
plugged in).
4. Connect the supplied Cat5 Ethernet
cable from the laptop network
adapter to the access point.
1.7.2 ViZion DR+ 1417V2 Wireless Panel in
AP Mode (Alternative method)
When the panel is in AP mode you will connect
to the panel’s broadcasted Wi-Fi network,
(which will be named the same as the serial
number of the panel), using the laptop’s internal
wireless adapter. For your internet connection,
you will connect to any available Wi-Fi network
using the external USB Wi-Fi adapter.
Equipment required for AP mode:
•ASUS Dual-Band Wi-Fi USB Adapter
(used for the Wi-Fi Internet connection)
•Link Cable (to preconfigure the panel’s
wireless settings)

[ViZion DR+ 1417V2 Wireless Panel Calibration Manual]
[Ultra 4.2.9.0]
10
Customer Support
1.800.366.5343 –
[email protected]
2 ViZion DR+ 1417V2 Wireless
Panel Hardware
2.1 Panel Calibration
Before performing the following steps, make
sure the wireless panel is powered on with a
fully charged battery, and connected with the
supplied Link cable.
1. From the Acquire screen, select
Options.
2. Select Device Configurations tab.
3. Click to highlight DEFAULT under the
“Configuration Pool”section.
4. Click on ViZion DR+ and the panel
device configuration section will appear
below it.
5. Scroll down to the Device section and
click on Utility to open the iDetector
interface.
Note: after clicking on Utility, the Maven
software will shutdown
communication between the panel
and the Ultra UAI software, and
close maven, and then iDetector
software will launch automatically
as a popup window.