Kontron 3.5-SBC-APL V2.0 User manual

Kontron 3.5"-SBC-APL V2.0 - Quick Installation Guide - Version 2.0 - P/N: 0D20ECXAPL020000 // 1

3.5"
-SBC-APL V2.0 - QUICK INSTALLATION GUIDE
Thank you for purchasing the Kontron 3.5"-SBC-APL V2.0 embedded board. This document provides information to allow
you to quickly install this product.
Packing Checklist
1. Take the 3.5"-SBC-APL V2.0 out of the packing box and check if the unit is properly secure in the plastic bag.
2. Check the contents of the carton box: (*: optional)
3.5"-SBC-APL V2.0 main board
1x DC IN Cable
SATA Cable*
COM Port Cable*
DIO Cable*
USB Cable*
SATA Cable With Power*
Audio Cable*
3G / 4G Mini SIM Card Holder Kit*

Kontron 3.5"-SBC-APL V2.0 - Quick Installation Guide - Version 2.0 - P/N: 0D20ECXAPL020000 // 2
Top Side Jumper and Internal Connector Locations
Jumper List
Item Designation Description
1 JP1 SIM Card Selection
2 JP2 Backlight Enable Selection
3 JP3 Panel & Backlight Power Selection
4 JP4 AT / ATX Power Mode Selection
5 JP5 M.2 Key B LED Pin Header
6 JP6 MPCIE Activity LED Pin Header
7 JP8 RTC Reset Selection
8 JP9 USB Power Selection
9 JP10 ME F/W Selection
Internal Connector List
Item Designation Description
10 CN1 DC 12V Power Input Wafer
11 BAT1 CR2032 Battery Power Input Wafer
12 FAN1 DC5V Fan Wafer
13 SATA1 Serial ATA Port 0 Connector
14 CN2 HDD Power Output Wafer
15 CN6 USB2.0 Port DN_1, DN_2 Pin Header
16 CN26 USB2.0 Port Wafer (Optional)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35

Kontron 3.5"-SBC-APL V2.0 - Quick Installation Guide - Version 2.0 - P/N: 0D20ECXAPL020000 // 3
Item Designation Description
17 CN12 Left Channel 3W Audio AMP Output Wafer
18 CN16 Right Channel 3W Audio AMP Output Wafer
19 CN11 Audio Input / Output Pin Header
20 FP1 Front Panel 1 Pin Header
21 FP2 Front Panel 2 Pin Header
22 CN17 COM1 RS-232/422/485 Port Wafer
23 CN18 COM2 RS-232/422/485 Port Wafer
24 CN19 COM3 RS-232 Port Wafer
25 CN20 COM4 RS-232 Port Wafer
26 CN21 COM5 RS-232 Port Wafer
27 CN22 COM6 RS-232 Port Wafer
28 CN14 Digital Input / Output Wafer
29 MPCIE1 Mini-PCI Express v1.2 Socket (Full Size)
30 CON1 NGFF M.2 Key B Socket
31 CN7 SIM Interface Wafer for MPCIE1 and M.2 Key B
32 CN3 Micro-SD Card Cage
33 DIMM1 DDR3L Memory SO-DIMM Socket
34 DIMM2 DDR3L Memory SO-DIMM Socket
35 CN8 P80_Header
Jumper Settings
SIM Card Selection (JP1)
Jumper Position Description
Pin 1-2
X MPCIE (default)
- M.2 Key B
“X” = Jumper set (short) and “-” = jumper not set (open)

Kontron 3.5"-SBC-APL V2.0 - Quick Installation Guide - Version 2.0 - P/N: 0D20ECXAPL020000 // 4
Backlight Enable Selection (JP2)
Jumper 1 Position Description
Pin 1-3 Pin 3-5
X - Backlight Enable Voltage = +3.3V
- X Backlight Enable Voltage = +5V
Jumper 2 Position Description
Pin 2-4 Pin 4-6
X - Active High
- X Active Low
“X” = Jumper set (short) and “-” = jumper not set (open)
Panel & Backlight Power Selection (JP3)
Jumper 1 Position Description
Pin 1-3 Pin 3-5
X - Backlight Power = +12V
- X Backlight Power = +5V
Jumper 2 Position Description
Pin 2-4 Pin 4-6
X - Panel Power = +3,3V
- X Panel Power = +5V
“X” = Jumper set (short) and “-” = jumper not set (open)
2
1
65
21
65

Kontron 3.5"-SBC-APL V2.0 - Quick Installation Guide - Version 2.0 - P/N: 0D20ECXAPL020000 // 5
AT / ATX Power Mode Selection (JP4)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - ATX Mode
- X AT Mode
“X” = Jumper set (short) and “-” = jumper not set (open)
M.2 Key B Activity LED Pin Header (JP5)
Pin Signal
1 LED+
2 LED-
MPCIE1 Activity LED Indication (JP6)
Pin Signal
1 LED+
2 LED-
2
3
1
1
2
1
2

Kontron 3.5"-SBC-APL V2.0 - Quick Installation Guide - Version 2.0 - P/N: 0D20ECXAPL020000 // 6
RTC Reset Selection (JP8)
Jumper Position Description
Pin 1-2
X Enable Clear CMOS RTC content
(board does not boot with the jumper in this position)
- Normal operation (default position)
“X” = Jumper set (short) and “-” = jumper not set (open)
USB Power Selection (JP9)
Jumper Position Description
Pin 1-2
X USB power is always supply.
- USB power will be cut off in S4 & S5 state.
“X” = Jumper set (short) and “-” = jumper not set (open)
ME F/W Selection (JP10)
Jumper Position Description
Pin 1-2
X ME F/W Disabled
- Normal Operation
“X” = Jumper set (short) and “-” = jumper not set (open)

Kontron 3.5"-SBC-APL V2.0 - Quick Installation Guide - Version 2.0 - P/N: 0D20ECXAPL020000 // 7
Bottom Side Internal Connector Locations
Item Designation Description
1 CN23 Backlight Power Output Wafer
2 LVDS1 18/24-bit, 1/2-channel LVDS Panel Connector
Real I/O Panel Connector Locations
Item Designation Description
1 CN15 HDMI Connector
2 CN13 DP Connector
3 CN10 GbE LAN2 RJ-45 Connector
4 CN9 GbE LAN1 RJ-45 Connector
5 CN5 USB3.0 Port 3,4 Type-A Connector
6 CN4 USB3.0 Port 1,2 Type-A Connector
1
2
4
3
6
5
1
2