Kontron KTQ67/Flex-Medical User manual

If it’s embedded, it’s Kontron
KTQ67/Flex-Medical Users Guide
KTD-N0849-C

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 2
Document revision history.
Revision
Date
By
Comment
C
Jan. 8th 2014
MLA
Added BIOS features: Force Boot Setup and PC Speaker/Beep.
B
Dec. 13th 2013
MLA
Revision merged KTD-N00829-E KTQ67 Users Guide.
A
Aug. 22nd 2013
MLA
First release
0
Aug. 26th 2011
MLA
Preliminary version
Copyright Notice:
Copyright 2011, KONTRON Technology A/S, ALL RIGHTS RESERVED.
No part of this document may be reproduced or transmitted in any form or by any means, electronically
or mechanically, for any purpose, without the express written permission of KONTRON Technology A/S.
Trademark Acknowledgement:
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer:
KONTRON Technology A/S reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve design
and/or performance.
Specifications listed in this manual are subject to change without notice. KONTRON Technology
assumes no responsibility or liability for the use of the described product(s), conveys no license or title
under any patent, copyright, or mask work rights to these products, and makes no representations or
warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration purposes only.
KONTRON Technology A/S makes no representation or warranty that such application will be suitable
for the specified use without further testing or modification.
Life Support Policy
KONTRON Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL
MANAGER OF KONTRON Technology A/S.
As used herein:
Life support devices or systems are devices or systems which, (a) are intended for surgical implant into
body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with
instructions for use provided in the labelling, can be reasonably expected to result in significant injury to
the user.
A critical component is any component of a life support device or system whose failure to perform can
be reasonably expected to cause the failure of the life support device or system, or to affect its safety or
effectiveness.
Document details

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 3
KONTRON Technology Technical Support & Services
If you have questions about installing or using your KONTRON Technology Product, check this User’s
Manual first – you will find answers to most questions here. To obtain support, please contact your local
Distributor or Field Application Engineer (FAE).
Before Contacting Support: Please be prepared to provide as much information as possible:
•CPU Board
1. Type.
2. Part Number (find PN on label)
3. Serial Number if available (find SN on label)
•Configuration
1. CPU Type, Clock speed
2. DRAM Type and Size.
3. BIOS Revision (Find the Version Info in the BIOS Setup).
4. BIOS Settings different than Default Settings (Refer to the BIOS Setup Section).
•System
1. O/S Make and Version.
2. Driver Version numbers (Graphics, Network, and Audio).
3. Attached Hardware: Harddisks, CD-rom, LCD Panels etc.
Warranty
KONTRON Technology warrants its products to be free from defects in material and workmanship
during the warranty period. If a product proves to be defective in material or workmanship during the
warranty period, KONTRON Technology will, at its sole option, repair or replace the product with a
similar product.
Replacement Product or parts may include remanufactured or refurbished parts or components.
The warranty does not cover:
1. Damage, deterioration or malfunction resulting from:
A. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
B. Repair or attempted repair by anyone not authorized by KONTRON Technology.
C. Causes external to the product, such as electric power fluctuations or failure.
D. Normal wear and tear.
E. Any other causes which does not relate to a product defect.
2. Removal, installation, and set-up service charges.
Exclusion of damages:
KONTRON TECHNOLOGY LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT
OF THE PRODUCT. KONTRON TECHNOLOGY SHALL NOT BE LIABLE FOR:
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT,
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF
TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL,
INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS,
EVEN IF ADVISED OF THEIR POSSIBILITY OF SUCH DAMAGES.
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Document details

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 4
Contents
Introduction .............................................................................................7
1Installation procedure........................................................................8
1.1 Installing the board .......................................................................................................................... 8
1.2 Requirement according to IEC60950 ................................................................................................... 9
2System Specification ........................................................................10
2.1 Component main data ..................................................................................................................... 10
2.2 System overview ............................................................................................................................. 14
2.3 Processor Support Table .................................................................................................................. 16
2.4 System Memory support................................................................................................................... 19
2.5 KTQ67 Graphics Subsystem............................................................................................................... 20
2.5.1 Intel® HD Graphics 3000 (example) ................................................................................................ 20
2.6 Power Consumption ........................................................................................................................ 21
3Connector Locations .........................................................................24
3.1 KTQ67/Flex-Medical – frontside........................................................................................................ 24
4Connector Definitions.......................................................................26
5IO-Area Connectors...........................................................................27
5.1 Display connectors (IO Area)............................................................................................................ 27
5.1.1 DVI (lower) connector – DVI-I ......................................................................................................... 27
5.1.2 DVI-D (upper) connector – DVI-D..................................................................................................... 28
5.2 Ethernet Connectors (IO Area).......................................................................................................... 29
5.3 USB Connectors (IO Area) ................................................................................................................ 30
5.3.1 USB Connector 0/1/2/3 (USB0/1/2/3)............................................................................................ 30
5.4 COM1 and COM2 Connectors (IO Area) ............................................................................................... 31
6Internal Connectors..........................................................................32
6.1 Power Connector (ATX/BTXPWR)....................................................................................................... 32
6.2 Fan Connectors (FAN_CPU) (J28) and (FAN_SYS) (J29).......................................................................33
6.3 PS/2 Keyboard and Mouse connector (KBDMSE) (J15)......................................................................... 34

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 5
6.4 Display connectors (Internal)........................................................................................................... 35
6.4.1 LVDS Flat Panel Connector (LVDS) (J39) (optionally)......................................................................... 35
6.5 SATA (Serial ATA) Disk interface (J22 – J27) ...................................................................................... 36
6.6 USB Connectors (USB)..................................................................................................................... 37
6.6.1 USB Connector 6/7 ........................................................................................................................ 37
6.6.2 USB Connector 8/9 (USB8/9) (J18).................................................................................................37
6.6.3 USB Connector 10/11 (USB10/11) (J17).......................................................................................... 38
6.6.4 USB Connector 12/13 (USB12/13) (J16).......................................................................................... 38
6.7 Serial COM3 – COM4 Ports (J20, J21)................................................................................................. 39
6.8 Audio Connector ............................................................................................................................. 40
6.8.1 Line2 and Mic2 .............................................................................................................................. 40
6.8.1 Audio Header Connector (AUDIO_HEAD) (J47) .................................................................................40
6.9 Power Button Connector (PWRBTN) (J48) ..........................................................................................41
6.10 Front Panel Connector (FRONTPNL) (J36) ..........................................................................................42
6.11 Feature Connector (FEATURE) (J30) .................................................................................................. 43
6.12 ”Load Default BIOS Settings” Jumper (J11) .......................................................................................45
6.13 ClrRTC (J12) ................................................................................................................................... 45
6.14 SPI Recover Jumper (J41)................................................................................................................ 46
6.15 SPI Connector (SPI) (J40)................................................................................................................ 47
6.16 XDP-CPU (Debug Port for CPU) (J14) ................................................................................................. 48
6.17 XDP-PCH (Debug Port for Chipset) (J13) ............................................................................................ 49
7Slot Connectors (PCIe, PCI)...............................................................50
7.1 PCIe Connectors.............................................................................................................................. 50
7.1.1 PCI-Express x16 Connector (PCIe x16).............................................................................................. 50
7.1.3 PCI-Express x4 Connector (PCIe x4) (J33) ........................................................................................ 52
7.2 PCI Slot Connectors ........................................................................................................................ 53
7.2.1 Signal Description – PCI Slot Connector ........................................................................................... 54
7.2.2 KTQ67 PCI IRQ & INT routing ........................................................................................................... 55
8On-board - & mating connector types .................................................56
9System Resources.............................................................................57
9.1 Memory Map................................................................................................................................... 57
9.2 PCI Devices .................................................................................................................................... 58
9.3 Interrupt Usage .............................................................................................................................. 59
9.4 IO Map........................................................................................................................................... 60

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 6
10 BIOS................................................................................................61
10.1 Main.............................................................................................................................................. 61
10.2 Advanced....................................................................................................................................... 62
10.2.1 Advanced -PCI Subsystem Settings ................................................................................................ 63
10.2.2 Advanced -APCI Settings ............................................................................................................. 68
10.2.3 Advanced -Trusted Computing ...................................................................................................... 69
10.2.4 Advanced -CPU Configuration ....................................................................................................... 70
10.2.5 Advanced -SATA Configuration...................................................................................................... 72
10.2.6 Advanced -Intel ® Rapid Start Technology ..................................................................................... 76
10.2.7 Advanced -Intel TXT (LT) Configuration.......................................................................................... 77
10.2.8 Advanced -Intel ® Anti-Theft Technology Configuration .................................................................. 78
10.2.9 Advanced -AMT Configuration ....................................................................................................... 79
10.2.10 Advanced -Acoustic Management Configuration .............................................................................81
10.2.11 Advanced -USB Configuration....................................................................................................... 82
10.2.12 Advanced -SMART Settings ........................................................................................................... 83
10.2.13 Advanced -Super IO Configuration................................................................................................. 84
10.2.14 Advanced -Voltage Monitor .......................................................................................................... 89
10.2.15 Advanced -Hardware Health Configuration..................................................................................... 90
10.2.16 Advanced -LAN Configuration ....................................................................................................... 92
10.2.17 Advanced -Delay Startup.............................................................................................................. 94
10.2.18 Advanced -Serial Port Console Redirection .....................................................................................95
10.2.19 Advanced -CPU PPM Configuration................................................................................................. 99
10.3 Chipset ........................................................................................................................................ 100
10.3.1 PCH-IO Configuration................................................................................................................... 101
10.3.2 System Agent (SA) Configuration .................................................................................................. 106
10.4 Boot............................................................................................................................................ 120
10.4.1 CSM16 parameters ....................................................................................................................... 122
10.4.2 Force Boot Setup ......................................................................................................................... 123
10.4.3 CSM parameters........................................................................................................................... 124
10.5 Security ....................................................................................................................................... 125
10.5.1 HDD Security Configuration .......................................................................................................... 126
10.6 Save & Exit................................................................................................................................... 127
11 AMI BIOS Beep Codes ......................................................................128
12 OS Setup........................................................................................129

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 7
Introduction
This manual describes the KTQ67/Flex-Medical made by KONTRON Technology A/S. In this manual
the board will also be denoted KTQ67.
The KTQ67/Flex-Medial is based on the Q67 chipset, support 2nd and 3rd generation Intel® i7 -, i5 -,
i3 2Core and 4Core processor and the Celeron B810 2Core, see “Processor Support Table for more
specific details.
Use of this Users Guide implies a basic knowledge of PC-AT hard- and software. This manual is
focused on describing the KTQ67 board special features and is not intended to be a standard PC-AT
textbook.
New users are recommended to study the short installation procedure stated in the following chapter
before switching-on the power.
All configuration and setup of the CPU board is either done automatically or manually by the user via
the BIOS setup menus. Only exception is the “Load Default BIOS Settings” Jumper.
Introduction

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 8
Warning: Turn off PSU (Power Supply Unit) completely (no mains power connected to the
PSU) or leave the Power Connectors unconnected while configuring the board. Otherwise
components (DRAM, LAN cards etc.) might get damaged. Make sure PSU has 3.3V monitoring
watchdog (standard ATX PSU feature), running the board without 3.3V will damage the board
within minutes.
!
!
Warning: When mounting the board to chassis etc. please notice that the board contains
components on both sides of the PCB which can easily be damaged if board is handled
without reasonable care. A damaged component can result in malfunction or no function at all.
1 Installation procedure
1.1 Installing the board
To get the board running, follow these steps. If the board shipped from KONTRON has already
components like DRAM, CPU and cooler mounted, then relevant steps below, can be skipped.
1. Turn off the PSU (Power Supply Unit)
2. Insert the DRAM(s) (UDIMM 240pin)
Be careful to push it in the slot(s) before locking the tabs. For a list of approved DRAM contact your
Distributor or FAE. See also chapter “System Memory Support”.
3. Install the processor
The CPU is keyed and will only mount in the CPU socket in one way. Use finger to open/ close the
CPU socket. Refer to supported processor overview for details.
4. Cooler Installation
Use heat paste or adhesive pads between CPU and cooler and connect the Fan electrically to the
FAN_CPU connector.
5. Connecting Interfaces
Insert all external cables for hard disk, keyboard etc. A monitor must be connected in order to be
able change BIOS settings.
6. Connect and turn on PSU
Connect PSU to the board by the ATX/BTXPWR and the 4-pin ATX+12V connectors.
7. Power Button
The PWRBTN_IN must be toggled to start the Power supply; this is done by shorting pins 16
(PWRBTN_IN) and pin 18 (GND) on the FRONTPNL connector (see Connector description). A
“normally open” switch can be connected via the FRONTPNL connector.
8. BIOS Setup
Enter the BIOS setup by pressing the <Del> key during boot up.
Enter Exit Menu and Load Optimal Defaults.
Refer to the “BIOS Configuration / Setup“ section of this manual for details on BIOS setup.
9. Mounting the board to chassis
When fixing the Motherboard on a chassis it is recommended using screws with integrated washer and
having diameter of ~7mm.
Note: Do not use washers with teeth, as they can damage the PCB and may cause short circuits.
Installation procedure
Note: To clear all BIOS settings, including Password protection, activate “Load Default BIOS Settings”
Jumper for ~10 sec (without power connected).

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 9
1.2 Requirement according to IEC60950
Users of KTQ67 should take care when designing chassis interface connectors in order to fulfil the
IEC60950 standard:
Lithium Battery precautions:
CAUTION!
Danger of explosion if battery is incorrectly
replaced.
Replace only with same or equivalent type
recommended by manufacturer.
Dispose of used batteries according
to the manufacturer’s instructions.
VORSICHT!
Explosionsgefahr bei unsachgemäßem
Austausch der Batterie.
Ersatz nur durch den selben oder einen vom
Hersteller empfohlenen gleichwertigen Typ.
Entsorgung gebrauchter Batterien nach
Angaben des Herstellers.
ADVARSEL!
Lithiumbatteri – Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Eksplosjonsfare ved feilaktig skifte av batteri.
Benytt samme batteritype eller en tilsvarende
type anbefalt av apparatfabrikanten.
Brukte batterier kasseres i henhold til
fabrikantens
instruksjoner.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laltevalmistajan
suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden
mukaisesti.
When an interface/connector has a VCC (or other power) pin, which is directly connected to a power
plane like the VCC plane:
To protect the external power lines of the peripheral devices, the customer has to take care about:
•That the wires have suitable rating to withstand the maximum available power.
•That the enclosure of the peripheral device fulfils the fire protecting requirements of IEC60950.
Installation procedure

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 10
2 System Specification
2.1 Component main data
The table below summarizes the features of the KTQ67/Flex –Medical embedded motherboard.
Form factor
KTQ67/Flex-Medical: Flex-ATX (190,5 mm by 228,6 mm)
Processor
Support the following Intel® Core™ processors via Socket H2 (LGA1155), ZIF Socket
•Intel® Core™ i7, 2nd and 3rd Generation
•Intel® Core™ i5, 2nd and 3rd Generation
•Intel® Core™ i3, 2nd and 3rd Generation
•Intel® Pentium® Desktop
•1066/1333MHz system bus and 3/6/8MB internal cache.
(Intel® Pentium® Desktop G622 only 1066MHz)
•Up to 95W (Thermal Guideline)
Memory
•4x DDR3 UDIMM 240pin socket
•Support single and dual ranks DDR3 1066/1333MT/s
(PC3-8500/PC3-10600)
•Support system memory from 256MB and up to 4x 8GB
Note: Less than 4GB displayed in System Properties using 32bit OS
(Shared Video Memory/PCI resources is subtracted)
•ECC not supported (chipset limitation)
Chipset
Intel Q67 PCH (Platform Controller Hub)
•Intel ® VT-d (Virtualisation Technology for Directed I/O)
•Intel ® TXT (Trusted Execution Technology)
•Intel ® vPRO
•Intel ® AMT (Active Management Technology) version 8
•Intel ® AT (Anti-Theft Technology)
•Intel ® HD Audio Technology
•Intel ® RST (Rapid Storage Technology)
•Intel ® RRT (Rapid Recover Technology)
•SATA (Serial ATA) 6Gb/s and 3Gb/s.
•USB revision 2.0
•PCI Express revision 2.0
•ACPI 3.0b compliant
•Dual Display support (Dual Graphic Pipes)
•Blue-ray HD video playback
Security
•Intel® Integrated TPM 1.2 support
Management
•Intel® Active Management Technology (Intel® AMT) 8.0
Audio
Audio, 7.1 Channel High Definition Audio Codec using the VIA 1708B codec
•Line-out
•Line-in
•Surround output: SIDE, LFE, CEN, BACK and FRONT
•Microphone: MIC1 and MIC2
•CDROM in
•SPDIF (electrical Interface only)
•On-board speaker (Electromagnetic Sound Generator like Hycom HY-05LF)
System Specification

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 11
Video
Intel ® HD Graphics 4000 or
Intel ® HD Graphics 3000 or
Intel ® HD Graphics 2500 or
Intel ® HD Graphics 2000 or
Intel ® HD Graphics, depending on actual CPU.
Analogue VGA and digital display ports via the Mobile Intel ® Q67 Chipset.
•DVI-I & DVI-D ports via Mobile Intel ® Q67 Chipset. (Digital single channel only).
•LVDS panel support (optional) up to 24 bit, 2 pixels/clock and 1920x1200.
•Dual independent pipes for Mirror and Dual independent display support
I/O Control
Via ITE IT8516E Embedded Controller and Winbond W83627DHG I/O Controller
(both via LPC Bus interface)
Peripheral
interfaces
•Six USB 2.0 ports on I/O area
•Eight USB 2.0 ports on internal pinrows
•Four Serial ports (RS232) on internal pinrows
•Two Serial ATA-600 IDE interfaces (blue)
•Four Serial ATA-300 IDE interfaces (black)
•RAID 0/1/5/10 support
•mSATA via mSATA connector
•PS/2 keyboard and mouse ports via pinrow
LAN
Support
•1x 10/100/1000Mbits/s LAN (ETHER1) using Intel® Lewisville 82579LM Gigabit
PHY connected to Q67 supporting AMT 8.0. Galvanic Isolated.
•1x 10/100/1000Mbits/s LAN (ETHER2) using Intel® Hartwell 82574L PCI Express
controller. Galvanic Isolated.
•PXE Netboot supported.
•Wake On LAN (WOL) supported
Expansion
Capabilities
•PCI Bus routed to 2x PCI slots (PCI Local Bus Specification Revision 3.0, 33MHz)
•PCI-Express slot(s) (PCIe 2.0):
•1 slot PCIe x16
•1 slot PCIe x4 (in a x16 slot)
•SMBus, compatible with ACCES BUS and I2C BUS, (via Feature connector)
•SPI bus routed to SPI connector
•DDC Bus routed to DP connector when DP Adapters are connected
•5 x digital input, (via Feature connector)
•13 x GPIOs (General Purpose I/Os), (via Feature connector)
•DAC, ADC, PWM and TIMER (Multiplexed), (via Feature connector)
•WAKE UP / Interrupt Inputs (Multiplexed), (via Feature connector)
•3 Wire Bus for GPIO Expansion (up to 152 GPIOs), (via Feature connector)
•8 bit Timer output, (via Feature connector)
System Specification

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 12
Hardware
Monitor
Subsystem
•Smart Fan control system, support Thermal® and Speed® cruise for FAN_CPU
•CPU die temperature input (Precision +/- 3ºC)
•Voltage monitoring
•Intrusion (Case Open) detect input, (via Feature connector)
•Sleep S4/S5# Indication, (via Feature connector)
•System Powergood Signal, (via Feature connector)
Power
Supply Unit
ATX/BTX (w. ATX+12V) PSU for full PCI/PCIe load.
Battery
Exchangeable 3.0V Lithium battery for on-board Real Time Clock and CMOS RAM.
Manufacturer Panasonic / Part-number CR-2032L/BN, CR2032N/BN or CR-2032L/BE.
Approximate 5 years retention.
Current draw is 5,7µA when PSU is disconnected and 0 µA in S0 – S5.
CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
BIOS
•Kontron Technology / AMI BIOS (EFI core version)
•Support for ACPI 3.0 ( Advanced Configuration and Power Interface), Plug & Play
oSuspend (S1 mode)
oSuspend To Ram (S3 mode)
oSuspend To Disk (S4 mode)
•“Always On” BIOS power setting
•RAID Support (RAID modes 0,1, 5 and 10)
Operating
Systems
Support
•WinXP (32b *)
•Windows 7 (32b + 64b *)
•WES7 (32b * + 64b *)
•Linux Fedora *
•Linux Ubuntu *
•VxWorks (not ready yet)
*= Out Of The Box installation test only
System Specification

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 13
Environmental
Conditions
Operating:
0°C – 60°C operating temperature (forced cooling). It is the customer’s
responsibility to provide sufficient airflow around each of the components to keep
them within allowed temperature range.
10% - 90% relative humidity (non-condensing)
Operating altitude: up to 2000 meters
Storage:
-20°C – 70°C; lower limit of storage temperature is defined by specification
restriction of on-board CR2032 battery. Board with battery has been verified for
storage temperature down to -40°C by Kontron.
5% - 95% relative humidity (non-condensing)
Electro Static Discharge (ESD) / Radiated Emissions (EMI): (Pending)
All Peripheral interfaces intended for connection to external equipment are ESD/
EMI protected.
EN 61000-4-2:2000 ESD Immunity
EN55022:1998 class B Generic Emission Standard.
Safety:
IEC 60950-1: 2005, 2nd Edition
UL 60950-1
CSA C22.2 No. 60950-1
Product Category: Information Technology Equipment Including Electrical
Business Equipment
Product Category CCN: NWGQ2, NWGQ8
File number: E194252
Theoretical MTBF:
211.994 / 100.475 hours @ 40ºC / 60ºC for the KTQ67/Flex
Restriction of Hazardous Substances (RoHS):
The KTQ67 is RoHS compliant.
Capacitor utilization:
No Tantalum capacitors on board
Only Japanese brand Solid capacitors rated for 100 ºC used on board
System Specification

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 14
2.2 System overview
The block diagram below shows the architecture and main components of the KTQ67. The key
component on the board is the Intel®Q67 (Cougar Point) Mobile Express Chipset.
More detailed block diagram on next page.
System Specification

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 15
Dual Channel DDR3
1067/1333/1600
4 x DIMM
Q67 PCH
PCIe x16 Graphics
Ivy Bridge or
Sandy Bridge
LGA1155
2x DisplayPort
VGA
PCIe x4 Slot
Intel 82574L 10/100/GBe
14x USB
(Gen2.0)
6x SATA
SDVO to LVDS (option)
VIA Codec
SPI
SPI
TPM
Intel Lewisville PHY
System Specification
IO controller
W83627DHG-P(T)
IO controller
ITE8516
PCI slot
PCI slot
COM3/4
COM1/2
FEATURE
FAN CPU/SYS

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 16
2.3 Processor Support Table
The KTQ67 is designed to support the following LGA1155 processors (up to 95W power consumption):
2nd and 3rd generation Intel® Core™ i7 processor
2nd and 3rd generation Intel® Core™ i5 processor
2nd and 3rd generation Intel® Core™ i3 processor
Pentium and Celeron
In the following list you will find all CPU’s supported by the chipset in according to Intel. Please notice
that Bus speed 1600 MHz has not been verified yet.
Embedded CPU’s are indicated by green text, successfully tested CPU’s are indicated by highlighted
text, successfully tested embedded CPU’s are indicated by green and highlighted text and failed
CPU’s are indicated by red text.
Some processors in the list are distributed from Kontron, those CPU’s are marked by an * (asterisk).
However please notice that this marking is only guide line and maybe not fully updated.
Processor
Brand
Clock
[GHz]
Turbo
[GHz]
Cores /
Threads
Bus
[MHz]
Cache
[MB]
CPU
Number
sSpec
no.
Step
TG
[W/ºC]
Note
3.5
3.9
4 / 8
1333/1600
8
3770K
SR0PL
E1
77/67.4
HDG4000
I7 3rd Gen.
3.4
3.9
4 / 8
1333/1600
8
3770
SR0PK
E1
77/67.4
HDG4000
(Ivy Bridge)
3.1
3.9
4 / 8
1333/1600
8
3770S
SR0PN
E1
65/69.1
HDG4000
2.5
3.7
4 / 8
1333/1600
8
3770T
SR0PQ
E1
45/69.8
HDG4000
3.5
3.9
4 / 8
1066/1333
8
2700K
SR0DG
D2
95/72.6
HDG3000
I7 2nd Gen.
3.4
3.8
4 / 8
1066/1333
8
2600
SR00B
D2
95/72.6
HDG2000
(Sandy Bridge)
3.4
3.8
4 / 8
1066/1333
8
2600K
SR00C
D2
95/72.6
HDG3000
2.8
3.8
4 / 8
1066/1333
8
2600S
SR00E
D2
65/69.1
HDG2000
3.4
3.8
4 / 4
1333/1600
6
3570
SR0T7
N0
77/67.4
HDG2500
I5 3rd Gen.
3.4
3.8
4 / 4
1333/1600
6
3570K
SR0PM
E1
77/67.4
HDG4000
(Ivy Bridge)
3.3
3.7
4 / 4
1333/1600
6
3550
SR0P0
E1
77/67.4
HDG2500
3.2
3.6
4 / 4
1333/1600
6
3470
SR0T8
N0
77/67.4
HDG2500
3.1
3.8
4 / 4
1333/1600
6
3570S
SR0T9
N0
65/69.1
HDG2500
3.1
3.5
4 / 4
1333/1600
6
3450
SR0PF
E1
77/67.4
HDG2500
3.1
3.3
4 / 4
1333/1600
6
3350P
SR0WS
E1
69/67.4
-
3.0
3.7
4 / 4
1333/1600
6
3550S
SR0P3
E1
65/69.1
HDG2500
3.0
3.2
4 / 4
1333/1600
6
3330
SR0RQ
E1
77/67.4
HDG2500
2.9
3.6
4 / 4
1333/1600
6
3475S
SR0PP
E1
65/69.1
HDG4000
2.9
3.6
4 / 4
1333/1600
6
3470S
SR0TA
N0
65/69.1
HDG2500
2.9
3.6
2 / 4
1333/1600
3
3470T
SR0RJ
L1
35/65.0
HDG2500 *
2.8
3.5
4 / 4
1333/1600
6
3450S
SR0P2
E1
65/69.1
HDG2500
2.7
3.5
4 / 4
1333/1600
6
3330S
SR0RR
E1
65/
HDG2500
2.3
3.2
4 / 4
1333/1600
6
3570T
SR0P1
E1
45/69.8
HDG2500
3.3
3.7
4 / 4
1066/1333
6
2550K
SR0QH
D2
95/72.6
-
I5 2nd Gen.
3.3
3.7
4 / 4
1066/1333
6
2500K
SR008
D2
95/72.6
HDG3000
(Sandy Bridge)
3.3
3.7
4 / 4
1066/1333
6
2500
SR00T
D2
95/72.6
HDG2000
3.2
3.5
4 / 4
1066/1333
6
2450P
SR0G1
D2
95/72.6
-
3.1
3.4
4 / 4
1066/1333
6
2380P
SR0G2
D2
95/72.6
-
3.1
3.4
4 / 4
1066/1333
6
2400
SR00Q
D2
95/72.6
HDG2000
3.0
3.3
4 / 4
1066/1333
6
2320
SR02L
D2
95/72.6
HDG2000
2.9
3.2
4 / 4
1066/1333
6
2310
SR02K
D2
95/72.6
HDG2000
2.8
3.1
4 / 4
1066/1333
6
2300
SR00D
D2
95/72.6
HDG2000
2.7
3.7
4 / 4
1066/1333
6
2500S
SR009
D2
65/69.1
HDG2000
2.7
3.5
2 / 4
1066/1333
3
2390T
SR065
Q0
35/65.0
HDG2000
2.5
3.3
4 / 4
1066/1333
6
2405S
SR0BB
D2
65/69.1
HDG3000
2.5
3.3
4 / 4
1066/1333
6
2400S
SR00S
D2
65/69.1
HDG2000
2.3
3.3
4 / 4
1066/1333
6
2500T
SR00A
D2
45/69.8
HDG2000
System Specification

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 17
Processor
Brand
Clock
[GHz]
Turbo
[GHz]
Cores /
Threads
Bus
[MHz]
Cache
[MB]
CPU
Number
sSpec
no.
Step
TG
[W/ºC]
Note
3.5
-
2 / 4
1333/1600
3
3250
SR0YX
P0
55/65.3
HDG2500
I3 3rd Gen.
3.4
-
2 / 4
1333/1600
3
3245
SR0YL
L1
55/65.3
HDG4000
(Ivy Bridge)
3.4
-
2 / 4
1333/1600
3
3240
SR0RH
L1
55/65.3
HDG2500
3.3
-
2 / 4
1333/1600
3
3225
SR0RF
L1
55/65.3
HDG4000
(No vPRO)
3.3
-
2 / 4
1333/1600
3
3220
SR0RG
L1
55/65.3
HDG2500
3.2
-
2 / 4
1333/1600
3
3210
SR0YY
P0
55/65.3
HDG2500
3.0
-
2 / 4
1333/1600
3
3250T
SR0YW
P0
35/65.0
HDG2500
2.9
-
2 / 4
1333/1600
3
3240T
SR0RK
L1
35/65.0
HDG2500
2.8
-
2 / 4
1333/1600
3
3220T
SR0RE
L1
35/65.3
HDG2500
3.4
-
2 / 4
1066/1333
3
2130
SR05W
Q0
65/69.1
HDG2000
I3 2nd Gen.
3.3
-
2 / 4
1066/1333
3
2125
SR0AY
J1
65/69.1
HDG3000
(Sandy Bridge)
3.3
-
2 / 4
1066/1333
3
2120
SR05Y
Q0
65/69.1
HDG2000
3.1
-
2 / 4
1066/1333
3
2105
SR0BA
J1
65/69.1
HDG3000
(No vPRO)
3.1
-
2 / 4
1066/1333
3
2100
SR05C
Q0
65/69.1
HDG2000
3.1
-
2 / 4
1066/1333
3
2102
SR05D
Q0
65/69.1
HDG2000
2.6
-
2 / 4
1066/1333
3
2120T
SR060
Q0
35/65.0
HDG2000
2.5
-
2 / 4
1066/1333
3
2100T
SR05Z
Q0
35/65.0
HDG2000
3.1
-
2 / 2
1066/1333
3
G870
SR057
Q0
65/69.1
HDG
3.0
-
2 / 2
1066/1333
3
G860
SR058
Q0
65/69.1
HDG
Pentium
2.9
-
2 / 2
1066/1333
3
G850
SR05Q
Q0
65/69.1
HDG
2.9
-
2 / 2
1066
3
G645
SR0RS
Q0
65/69.1
HDG
2.8
-
2 / 2
1066/1333
3
G840
SR05P
Q0
65/69.1
HDG
2.8
-
2 / 2
1066
3
G640
SR059
Q0
65/69.1
HDG
2.7
-
2 / 2
1066
3
G632
SR05N
Q0
65/69.1
HDG
2.7
-
2 / 2
1066
3
G630
SR05S
Q0
65/69.1
HDG
2.8
-
2 / 2
1066/1333
3
G860T
SR0MF
Q0
35/65.0
HDG
2.6
-
2 / 2
1066
3
G620
SR05R
Q0
65/69.1
HDG
2.6
-
2 / 2
1066
3
G622
-
-
65/69.1
HDG
2.5
-
2 / 2
1066
3
G645T
SR0S0
Q0
35/65.0
HDG
2.4
-
2 / 2
1066
3
G640T
SR066
Q0
35/65.0
HDG
2.2
-
2 / 2
1066
3
G620T
SR05T
Q0
35/65.0
HDG
2.3
-
2 / 2
1066
3
G630T
SR05U
Q0
35/65.0
HDG
2.7
-
2 / 2
1333
2
G1620
SR10L
P0
55
HDG *
2.7
-
2 / 2
1066
2
G555
SR0RZ
Q0
65/69.1
HDG
2.6
-
2 / 2
1333
2
G1610
SR10K
P0
55
HDG *
2.6
-
2 / 2
1066
2
G550
SR061
Q0
65/69.1
HDG
2.5
-
2 / 2
1066
2
G540
SR05J
Q0
65/69.1
HDG
Celeron
2.4
-
2 / 2
1066
2
G530
SR05H
Q0
65/69.1
HDG
2.3
-
2 / 2
1333
2
G1610T
SR10M
P0
35/
HDG *
2.2
-
2 / 2
1066
2
G550T
SR05V
Q0
35/65.0
HDG
2.1
-
2 / 2
1066
2
G540T
SR05L
Q0
35/65.0
HDG
2.0
-
2 / 2
1066
2
G530T
SR05K
Q0
35/65.0
HDG
2.0
-
1 / 2
1066/1333
1.5
G470
SR0S7
Q0
35/65.5
HDG
1.8
-
1 / 2
1066
1.5
G460
SR0GR
Q0
35/65.5
HDG
1.6
-
1 / 1
1066
1
G440
SR0BY
Q0
35/65.5
HDG
(*) ECC not supported on KTQ67.
Not all CPUs, even of same type, support all functions ex. i7 3770K, i7 2600K, i5 3570K, 3450, 3450S,
3350P, 3330S, 3330 and i5 2500K, 2300,2310, 2320, 2380P, 2450P, 2550K doesn’t support vPro while
all other i7 and i5 does.
Most of the processors are supporting the Enhanced Intel® SpeedStep® which is improved SpeedStep
technology for faster transition between voltage (power saving states) and frequency states with the
result of improved power/performance balance. For more details see http://ark.intel.com
Intel® Turbo Boost Technology 2.0 is supported by i5 and i7, as indicated in above list of processors,
and is enabling overclocking of all cores, when operated within the limits of thermal design power,
temperature and current.
System Specification

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 18
!
Warning: Make sure sufficient airflow is always present around the components located below
the cooler. Different coolers are available on the market and some is not generating any airflow
or is blocking the airflow around these components, causing reduced lifetime.
Sufficient cooling must be applied to the CPU in order to remove the effect as listed in above table
(Thermal Guideline). The sufficient cooling is also depending on the maximum (worst-case) ambient
operating temperature and the actual load of processor.
It is recommended to use a cooler like the Kontron
PN 1046-6305 “KTQ67 Cooler”.
The design of this cooler makes sure airflow is
always present around the components below the
cooler. Even if Fan is set to be off, it is still running
a minimum RPM (Rotation Per Minute).
Air sucked in to the cooler
Air blown out of the cooler
Components below the cooler
Note: The temperature of the air blown out of the cooler should be 70
º
C maximum.
System Specification

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 19
2.4 System Memory support
The KTQ67/Flex-Medical has four DDR3 UDIMM sockets. The sockets support the following memory
features:
•4x DDR3 1.5V UDIMM 240-pin
•Dual-channel with 2 UDIMM per channel
•Single/dual rank unbuffered 1066/1333MT/s (PC3-8500/PC3-10600)
From 256MB and up to 4x 8GB.
Note: Less than 4GB displayed in System Properties using 32bit OS
(Shared Video Memory/PCI resources is subtracted)
•SPD timings supported
•ECC not supported
The installed DDR3 DIMM should support the Serial Presence Detect (SPD) data structure. This allows
the BIOS to read and configure the memory controller for optimal performance. If non-SPD memory is
used, the BIOS will attempt to configure the memory settings, but performance and reliability may be
impacted.
Memory Operating Frequencies
Regardless of the DIMM type used, the memory frequency will either be equal to or less than the
processor system bus frequency. For example, if DDR3 1600 memory is used with a 1333 MHz system
bus frequency processor, the memory clock will operate at 666 MHz. The table below lists the resulting
operating memory frequencies based on the combination of DIMMs and processors.
DIMM Type
Module
name
Memory
Data
transfers
[Mill/s]
Processor
system bus
frequency
[MHz]
Resulting
memory clock
frequency
[MHz]
Peak transfer
rate
[MB/s]
DDR3 1066
PC3-8500
1066
1066 / 1333
533
8533
DDR3 1333
PC3-10600
1333
1333
666
10666
DDR3 1600
PC3-12800
1600
1333
666
10666
Notes: Kontron offers the following memory modules:
1054-2766 1GB DDR3 1066
1031-9872 1GB DDR3 1333
1054-3706 1GB DDR3 1600
1054-2768 2GB DDR3 1066
1054-3702 2GB DDR3 1333
1054-3707 2GB DDR3 1600
1054-3700 4GB DDR3 1066
1054-3703 4GB DDR3 1333
1054-3708 4GB DDR3 1600
1054-3704 8GB DDR3 1333
1052-5601 8GB DDR3 1600
DDR3 (SLOT B1)
DDR3 (SLOT B0)
DDR3 (SLOT A1)
DDR3 (SLOT A0)
(Example Flex version)
System Specification
It has not been verified that the combination of CPU
supporting Bus Speed 1600 MHz and DDR3 1600 actually
runs at 1600 MHz.
In order to support Intel ® AMT (Management Engine) SLOT
A0 must always be populated. In case of using more than a
single DIMM it is recommended to populate A0 + B0 first.

KTQ67/Flex -Medical Users Guide
KTD-N0849-C Page 20
2.5 KTQ67 Graphics Subsystem
The KTQ67 support Intel ® HD Graphics 4000, 3000, 2500, 2000 or Intel ® HD Graphics, depending on
actual CPU. However please notice that even though an Ivy Bridge CPU supporting Triple Independent
Displays are used then on the KTQ67 only Dual Independent Displays are supported.
Supports 2x DVI (single channel) via DVI-I and DVI-D connector and optionally LVDS.
Up to two displays (any two display outputs) can be activated at the same time and be used to
implement dual independent display support or mirror display support. PCIe and PCI graphics cards can
be used to replace on-board graphics or in combination with on-board graphics.
2.5.1 Intel® HD Graphics 3000 (example)
Features of the Intel HD Graphics 3000 build into the i3, i5 and i7 processors, includes:
•High quality graphics engine supporting
oDirectX10.1 and OpenGL 3.0 compliant
oShader Model 4.1 support
oIntel ® Clear Video HD Technology
oIntel ® Quick Sync Video Technology
oIntel ® Flexible Display Interface (Intel ® FDI)
oCore frequency of 350 - 1300 (Turbo) MHz
oMemory Bandwidth up to 21.3 GB/s
o12 3D Execution Units
o1.62 GP/s and 2.7 GP/S pixel rate (DP outputs)
oHardware Acceleration full MPEG2, full VC-1 and full AVC
oDynamic Video Memory Technology (DVMT) support up to 1720 MB
•LVDS panel Support (optional), 18/24 bit colours in up to WUXGA (1920x1200) @60 Hz and
SPWG (VESA) colour coding. OpenLDI (JEIDA) colour coding is 18 bit with or without Dithering.
System Specification