Kontron MOPSlcdLX User manual

MOPSlcdLX
KTD-S0005-0

User Information
MOPSlcdLX User's Guide
Table of Contents
» Table of Contents «
1User Information .............................................................................1
1.1 About This Document.................................................................................................... 1
1.2 Copyright Notice.......................................................................................................... 1
1.3 Trademarks................................................................................................................. 1
1.4 Standards................................................................................................................... 1
1.5 Warranty .................................................................................................................... 1
1.6 Life Support Policy ....................................................................................................... 2
1.7 Technical Support ........................................................................................................ 2
2Introduction ...................................................................................3
2.1 MOPS Embedded Line Family .......................................................................................... 3
2.2 MOPSlcdLX Overview ..................................................................................................... 3
3Specifications .................................................................................4
3.1 Functional Specifications .............................................................................................. 4
3.2 Block Diagram ............................................................................................................. 6
3.3 Mechanical Specifications.............................................................................................. 7
3.4 Electrical Specifications ................................................................................................ 7
3.5 External Real-Time Clock Battery..................................................................................... 8
3.6 Environmental Specifications ......................................................................................... 8
3.7 MTBF ......................................................................................................................... 9
4Getting Started.............................................................................. 10
5System Memory ............................................................................. 11
6ISA Bus Expansion.......................................................................... 12
6.1 Connector .................................................................................................................12
6.2 Hints ........................................................................................................................12
7PCI Bus Expansion.......................................................................... 13
7.1 Configuration of VI/O and VCC.........................................................................................13
8Graphics Interface.......................................................................... 14
8.1 CRT Connector ............................................................................................................14
8.2 Flat Panel Connector....................................................................................................14
8.2.1 Connector .............................................................................................................................. 15
8.3 Connecting a Flat Panel................................................................................................16
8.4 Available Video Modes .................................................................................................16
8.5 Extended VESA Modes ..................................................................................................17

User Information
MOPSlcdLX User's Guide
Table of Contents
9Serial Port Interfaces ...................................................................... 18
9.1 Connector .................................................................................................................18
10 Parallel Port Interface..................................................................... 19
10.1 Connector .................................................................................................................19
11 PS/2 Keyboard Interface.................................................................. 20
11.1 Connector .................................................................................................................20
11.2 Signal Description.......................................................................................................20
12 PS/2 Mouse Interface...................................................................... 21
12.1 Connector .................................................................................................................21
13 USB Interface................................................................................ 22
13.1 Connector .................................................................................................................22
13.2 Limitations ................................................................................................................22
14 Floppy Drive Interface..................................................................... 23
14.1 Connector .................................................................................................................23
15 EIDE Interface (P-ATA) .................................................................... 24
15.1 Connector .................................................................................................................24
16 LAN Controller............................................................................... 25
16.1 Connector .................................................................................................................25
17 Power Supply ................................................................................ 26
17.1 Connector .................................................................................................................26
17.2 Power Pins.................................................................................................................26
17.3 External Battery .........................................................................................................27
18 Crisis Management ......................................................................... 28
19 CPU/Memory Speed ........................................................................ 29
20 Special Hardware Hints ................................................................... 30
20.1 ISA Bus Limitations .....................................................................................................30
20.2 PCI Bus Limitations .....................................................................................................30
20.3 Security Block ............................................................................................................30
21 Setup Guide .................................................................................. 31
21.1 Start PHOENIX/AWARD BIOS Setup Utility ........................................................................31
21.2 Menu Bar...................................................................................................................32
21.3 Main Menu.................................................................................................................32
21.3.1 IDE Master or Slave Submenu.....................................................................................................33
21.4 Advanced BIOS Features...............................................................................................33

User Information
MOPSlcdLX User's Guide
Table of Contents
21.5 Advanced Chipset Features ...........................................................................................35
21.6 Integrated Peripherals .................................................................................................36
21.7 PnP/PCI Configurations................................................................................................36
21.8 PC Health Status .........................................................................................................37
21.9 Board Information ......................................................................................................37
Appendix A: System Resources ................................................................... 38
A.1 Interrupt Request (IRQ) Lines........................................................................................38
A.2 Direct Memory Access (DMA) Channels ............................................................................39
A.3 Memory Area..............................................................................................................39
A.4 I/O Address Map .........................................................................................................40
A.5 PCI Devices ................................................................................................................41
A.6 System Management Bus (SMBus) ..................................................................................41
Appendix B: Connector Layout.................................................................... 42
B.1 Connector Locations....................................................................................................42
B.2 Mechanical Dimensions................................................................................................43
B.3 Mating Connectors ......................................................................................................44
B.4 Pinout Tables .............................................................................................................45
Appendix C: Reference Documents .............................................................. 49
Appendix D: Document Revision History ....................................................... 50

KTD-S0005-0 Page 1 User Information
MOPSlcdLX User's Guide
1User Information
1.1 About This Document
This document provides information about products from KONTRON Technology A/S and/or its subsidiaries.
No warranty of suitability, purpose or fitness is implied. While every attempt has been made to ensure that
the information in this document is accurate the information contained within is supplied 'as-is' - no
liability is taken for any inaccuracies. Manual is subject to change without prior notice.
KONTRON assumes no responsibility for the circuits, descriptions and tables indicated as far as patents or
other rights of third parties are concerned.
1.2 Copyright Notice
Copyright © 2006 - 2009, KONTRON Technology A/S, ALL RIGHTS RESERVED.
No part of this document may be reproduced or transmitted in any form or by any means, electronically or
mechanically, for any purpose without the express written permission of KONTRON Technology A/S.
1.3 Trademarks
Brand and product names are trademarks or registered trademarks of their respective owners.
1.4 Standards
KONTRON Technology A/S is certified to ISO 9000 standards.
1.5 Warranty
This product is warranted against defects in material and workmanship for the warranty period from the
date of shipment. During the warranty period KONTRON Technology A/S will at its discretion decide to
repair or replace defective products.
Within the warranty period the repair of products is free of charge as long as warranty conditions are
observed.
The warranty does not apply to defects resulting from improper or inadequate maintenance or handling by
the buyer, unauthorized modification or misuse, operation outside of the product’s environmental speci-
fications or improper installation or maintenance.
KONTRON Technology A/S will not be responsible for any defects or damages to third party products that
are caused by a faulty KONTRON Technology A/S product.

KTD-S0005-0 Page 2 User Information
MOPSlcdLX User's Guide
1.6 Life Support Policy
KONTRON Technology's products are not for use as critical components in life support devices or systems
without express written approval of the general manager of KONTRON Technology A/S.
As used herein:
Life support devices or systems are devices or systems which
a) are intended for surgical implant into body or
b) support or sustain life and whose failure to perform, when properly used in accordance with instructions
for use provided in the labelling, can be reasonably expected to result in significant injury to the user.
A critical component is any component of a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.
1.7 Technical Support
Please consult our Web site at http://www.kontron.com/support for the latest product documentation,
utilities, drivers and support contacts. In any case you can always contact your board supplier for technical
support.
Before contacting support please be prepared to provide as much information as possible:
Board identification:
Type
Part number (find PN on label)
Serial number (find SN on label)
Board configuration:
DRAM type and size
BIOS revision (find in the BIOS Setup)
BIOS settings different than default settings (refer to the BIOS Setup section)
System environment:
O/S type and version
Driver origin and version
Attached hardware (drives, USB devices, LCD panels ...)

KTD-S0005-0 Page 3 Introduction
MOPSlcdLX User's Guide
2Introduction
2.1 MOPS Embedded Line Family
Each MOPS is a member of the PC/104 SBC family of KONTRON Technology A/S.
MOPS embedded line modules are characterized by interfaces for 2 x USB, Fast LAN, PS/2 keyboard and
mouse connector, an ISA bus, CRT interface as well as serial and parallel ports.
These homogeneous features facilitate easy upgrades within the MOPS embedded line product family. Con-
nection of LCD panels is simplified when using the onboard standard JILI (40 pins) or JILI30 interface.
As part of the standard features package all MOPS modules come with a JIDA interface which is integrated
into the BIOS of the SBC modules. This interface enables hardware independent access to the MOPS fea-
tures that can't be accessed via standard APIs. Functions such as watchdog timer, brightness of panel
backlight and user bytes in EEPROM can be configured with ease by taking advantage of this standard MOPS
module feature.
2.2 MOPSlcdLX Overview
Please refer to the following matrix to choose the product that suits your needs best.
Article number ISA bus PCI bus
01036-0000-53-4 
01036-0000-53-5 

KTD-S0005-0 Page 4 Specifications
MOPSlcdLX User's Guide
3Specifications
3.1 Functional Specifications
Processor: AMD GeodeTM LX800
64 kB data and 64 kB instruction L1 cache
128 kB L2 cache
Integrated memory controller run with one DDR200 to DDR266 unbuffered DDR-SDRAM (SO-
DIMM form factor) up to 1GB
Integrated display controller with dual display support (CRT/TFT) and up to 254 MB video
RAM (UMA)
Chipset: AMD GeodeTM CS5536
64 bit, 66 MHz GeodeLinkTM interface
External PCI bus with 32 bit / 33 MHz operation (PCI V2.2 compliant)
One parallel ATA PCI IDE controller
Four USB channels (OHCI/EHCI), only two channels available
Onchip Video Graphics Array (VGA)
CRT monitor interface (resolution: up to 1920x1440 pixel)
LVDS flatpanel interface supports dual clock with 18/24 bit color depth (resolution: max.
1600x1200 pixel, limited to LVDS Transmitter)
Onchip Parallel-ATA (P-ATA)
Supports PIO mode, Multiword DMA and Ultra DMA up to UDMA5
Onchip Universal Serial Bus (USB)
Two ports are capable to handle USB1.1 (OHCI) and USB2.0 (EHCI)
Super-I/O (LPC): Winbond W83627HG
Two serial ports (RS-232 compatible)
One parallel port configurable as enhanced parallel port (EPP) with bidirectional capability
One legacy floppy interface
PS/2 keyboard and mouse controller
Watchdog timer

KTD-S0005-0 Page 5 Specifications
MOPSlcdLX User's Guide
Fast Ethernet (PCI): Intel®82551ER
Full duplex operation at 10/100 Mbps
Fully compliant with IEEE 802.3 and IEEE 802.3u
External ISA bus (LPC): Fintek F85226F
One PC/104 bus connector, 8/16 bit I/O and memory access
All ISA interrupts and 8 bit DMA signals available (16 bit DMA not supported)
Bus master mode not supported
External PCI bus
One PCI-104 bus connector, only 3.3V PCI cards supported
BIOS: AWARD, 512 kb Flash BIOS
Real-Time Clock (RTC) with CMOS RAM

KTD-S0005-0 Page 6 Specifications
MOPSlcdLX User's Guide
3.2 Block Diagram
CPU
AMD GeodeTM LX800
Companion
AMD GeodeTM
CS5536
X15005
Graphic
Controller
FWH
Flash
(BIOS)
PCI Bus
DDR-
SDRAM
MOPSlcdLX
USB
Controller
IDE
Controller
SDRAM
Controller
P-ATA_
X15006
X15007
USB 0-1_
Ethernet
i82551ER
LVDS
Transmitter
VT1631L LVDS_
X12000
Super-I/O
W83627HG
GPI/O
Serial PortsFloppy RS-232
Interface
MAX211E
X15004
X15003
X16000 LAN_
LPC Bus
LPC
Eeprom
JIDA
AT24C04
X8000
Temp.
Sensor
LM86 SMBus
X12001 CRT_
Parallel Port
PS/2 Mouse +
Keyboard
X15000
X15001
RS-232
Interface
MAX211E
X15002 PS/2 Keyboard_
Watchdog
I2C_
PCI Bus_
X11000
X14001 PS/2 Mouse_
ISA-Bridge
F85226F
X10000
ISA Bus

KTD-S0005-0 Page 7 Specifications
MOPSlcdLX User's Guide
3.3 Mechanical Specifications
Dimensions
96 x 90 mm (3.77" x 3.55")
Height on top approx. 11.5 mm
Height on bottom approx. 10.5 mm
3.4 Electrical Specifications
Supply Voltage
+5V DC ±5%
Supply Voltage Ripple
Maximum 100mV peak to peak 0 – 20 MHz
Supply Current (DOS prompt)
Power consumption tests were executed during the DOS prompt with 256 MB DDR SDRAM, CRT monitor, USB
keyboard and CF card as boot device (default BIOS settings).
Full Load Soft Off S5
[A] [W] [A] [W]
1.10 5.50 0.20 1.00
Supply Current (Windows®XP SP3)
The power consumption tests were executed during Windows®XP SP3 by using a tool to stress the CPU
(100% load) and extensive 2D graphic. The boards were ran with 256 MB DDR SDRAM, CRT monitor, PS/2
keyboard, USB mouse and a CF card as boot device (default BIOS settings).
Full Load Idle
[A] [W] [A] [W]
1.45 7.25 0.95 4.75

KTD-S0005-0 Page 8 Specifications
MOPSlcdLX User's Guide
3.5 External Real-Time Clock Battery
Voltage range: +2.4V - +3.6V (typ. +3.0V)
Maximum current 10μA @ +3.0V
English:
CAUTION ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions.
Deutsch:
VORSICHT ! Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch den selben oder einen vom Hersteller empfohlenen
gleichwertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
French:
ATTENTION ! Risque d'explosion avec l'échange inadéquat de la batterie. Remplacement seulement par le même ou un type équivalent recommandé
par le producteur. L'évacuation des batteries usagées conformément à des indications du fabricant.
Danish:
ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig Håndtering. Udskifting må kun ske med batteri af samme fabrikant og type. Lever det
brugte batteri tilbage til leverand∅ren.
Finnish:
VAROITUS ! Paristo voi rãjãhtãã, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laltevalmistajan suosittelmaan tyyppiln. Havita
kaytetty paristo valmistajan ohjeiden mukaisesti.
Spanish:
Precaución ! Peligro de explosión si la batería se sustituye incorrectamente. Sustituya solamente por el mismo o tipo equivalente recomendado por
el fabricante. Disponga las baterías usadas según las instrucciones del fabricante.
The battery of this product is not considered to be accessible by the end user. Therefore the safety instructions are only given in english, german,
french, danish, finish and spanish language.
If the battery of this product however is accessible by the end user, it is in the responsibility of the customer to give the corresponding safety
instructions in the required language(s).
3.6 Environmental Specifications
Temperature
Operating: (with appropriate airflow):
Ambient temperature: 0 to +60°C 1)
Non-operating: -10 to +85°C
Note: 1) The maximum operating temperature is the maximum measurable temperature on any spot on a module’s surface. You
must maintain the temperature according to the above specification.
Humidity
Operating: 10% to 90% (non condensing)
Non operating: 5% to 95% (non condensing)

KTD-S0005-0 Page 9 Specifications
MOPSlcdLX User's Guide
3.7 MTBF
The following MTBF (Mean Time Between Failure) values were calculated using a combination of manufac-
turer’s test data, if the data was available, and a Bellcore calculation for the remaining parts. The Bellcore
calculation used is 'Method 1 Case 1'. In that particular method the components are assumed to be
operating at a 50% stress level in a 40°C ambient environment and the system is assumed to have not been
burned in. Manufacturer’s data has been used wherever possible. The manufacturer’s data, when used, is
specified at 50°C, so in that sense the following results are slightly conservative. The MTBF values shown
below are for a 40°C in an office or telecommunications environment. Higher temperatures and other envi-
ronmental stresses (extreme altitude, vibration, salt water exposure, etc.) lower MTBF values.
System MTBF (hours): tbd
Note: Fans usually shipped with KONTRON Technology A/S products have 50,000-hour typical operating life. The above esti-
mation assumes no fan but a passive heat sinking arrangement. Estimated RTC battery life (as opposed to battery failures)
is not included in the MTBF calculation. The RTC battery lifetime has to be considered separately. Battery life depends on
both temperature and operating conditions. When the KONTRON unit has external power; the only battery drain is from
leakage paths.

KTD-S0005-0 Page 10 Getting Started
MOPSlcdLX User's Guide
4Getting Started
Getting started with the MOPSlcdLX is very easy. Take the following steps:
Plug a suitable DDR-SDRAM memory module into the RAM socket.
Plug the MOPSlcdLX to the PC/104 bus connector on the starter kit baseboard.
Make all necessary connections from the MOPSlcdLX to the starter kit board (cables come with
the starter kit). The starter kit board offers various interfaces on standard connectors.
Connect the CRT monitor to the CRT interface or a LCD panel to the JILI interface by using the
corresponding adapter cable.
Plug a keyboard and/or mouse to the PS/2 connectors.
Plug a data cable to the hard disk interface. Attach the hard disk to the connector at the oppo-
site end of the cable. If necessary connect the power supply to the hard disk’s power connec-
tor.
Make sure all your connections have been made correctly. Turn on the power.
Enter the BIOS by pressing the Del key during boot-up. Make all changes in the BIOS Setup.
See the BIOS Setup chapter of this manual for details.

KTD-S0005-0 Page 11 System Memory
MOPSlcdLX User's Guide
5System Memory
The MOPSlcdLX uses only 200 pin Small Outline Dual Inline Memory Modules (SODIMMs). One socket is
available for 2.5V unbuffered DDR200 up to DDR266 SDRAM of up to 1 GB.
The total amount of memory available on the SDRAM module is used for main memory and graphic memory
on the MOPSlcdLX. Shared Memory Architecture (SMA) manages the sharing of system memory between
graphic controller and processor. Therefore the full memory size is not available for software applications.
Up to 254 MB of system memory are used as graphic memory.
Attention: DDR333 / DDR400 modules can only be operated with the DDR266 timing

KTD-S0005-0 Page 12 ISA Bus Expansion
MOPSlcdLX User's Guide
6ISA Bus Expansion
The design of the MOPSlcdLX follows the standard PC/104 form factor and offers ISA bus signals for the use
of standard PC/104 adapter cards.
The PC/104 bus consists of two connectors that use 104 pins in total.
XT bus connector (64 pins)
AT bus connector (40 pins, which is optional for 16 bit data bus system)
The pinout of the PC/104 bus connectors corresponds to the pinout of the ISA bus connectors with some
added ground pins. The two PC systems with different form factors are electrically compatible.
The XT bus connector, row A and B.
The corresponding 64 pin stackthrough header (ISA bus = 62 pins) has two added ground pins at the end of
the connector (pin A32 and pin B32). The pinout between PC/104 bus and XT ISA bus is identical between
A1 - A31 and B1 - B31.
The AT bus extension connector, row C and D
The corresponding 40 pin stackthrough header (ISA bus = 36 pins) has four added ground pins, two on
each side of the connector. To avoid confusion the first two pins are defined as pin C0 and pin D0. The
additional ground pins at the end of the connector are defined as C19 and D19. The pinout between PC/104
bus and AT ISA bus is identical between C1 - C18 and D1 - D18.
6.1 Connector
The MOPSlcdLX features both – XT bus and AT bus extension – on two dual-row socket connectors with 2.54
mm x 2.54 mm grid (0.1" x 0.1").
The PC/104 XT bus is available through the X10000A connector. The PC/104 AT bus is available through the
X10000B connector.
6.2 Hints
PC/104 adapter cards are mounted in a stack-through manner. Adapter cards are designed with plugs on
their undersides that mate with the PC/104 socket connectors of MOPSlcdLX. PC/104 adapters can support
the socket connector version on their topside and allow additional stacking of adapters.
Whenever possible use the MOPSlcdLX as top module of the PC/104 stack as the CPU board is normally the
board with the highest heat dissipation.

KTD-S0005-0 Page 13 PCI Bus Expansion
MOPSlcdLX User's Guide
7PCI Bus Expansion
A quad-row socket trough-hole connector with a 2 x 2 mm (0.79" x 0.79") pitch implements the standard
32 bit PCI bus signals. The PCI-104 bus is available through the standard connector X11000.
A description of signals, including electrical characteristics and timings, is beyond the scope of this docu-
ment. Please refer to the official PCI bus and PC/104-plus specifications for more details.
Under no circumstances 5V PCI cards may be used on the MOPSlcdLX board. Only Universal and 3.3V add on
cards are permitted. VI/O and VCC are open (default) or set to 3.3V on the PCI bus. 5V PCI add on cards can
irretrievably damage the MOPSlcdLX board due to a short curcuit with VI/O or VCC. Before using a PCI add on
card please make absolutely sure that this card is conform to these requirements. The LX chipset does only
support a 3.3V PCI bus.
7.1 Configuration of VI/O and VCC
If it is ensured that the PCI expansion cards are types of 3.3V only zero-ohm bridges can be set.
Top side
Bottom side
Attention: 5V PCI expansion cards can damage the board.
Four slots are available via the connector X11000 (IDSEL, /IRQ) but only three slots are busmaster capable.

KTD-S0005-0 Page 14 Graphics Interface
MOPSlcdLX User's Guide
8Graphics Interface
The graphics accelerator supports CRT monitors and a variety of LCD panels with single or dual clock, color
depths of 18/24 bit and resolutions up to 1920x1440 for CRT and UXGA (1600x1200) for LCD.
8.1 CRT Connector
The CRT monitor interface is available through the X12001 connector (6 pins). To have the signals available
on a standard DSUB15 CRT monitor connector an adapter cable is required. A 15 pin DSUB cable is avail-
able from KONTRON (KAB-VGA-2, part number 96053-0000-00-0).
Header Pin Signal Name Function DSUB15
1 RED Red video signal 1
2 GRN Green video signal 2
3 BLU Blue video signal 3
4 GND Ground 5 - 8
5 VSYNC Vertical sync 14
6 HSYNC Horizontal sync 13
8.2 Flat Panel Connector
The LVDS interface for the flat panel is available through the X12000 connector (40 pins) on the top side of
the board. The implementation of this subsystem complies with the JILI specification of KONTRON Techno-
logy A/S. A variety of cables for different display types are available from KONTRON. Please refer to the
actual cable list on the KONTRON website for part numbers and cable names.
When using a LCD additional voltages may be required to drive the displays logic and supply the backlight
converter. The display logic may require +5V or +3.3V, backlight converters usually are +5V or +12V types.
When using a KONTRON JILI cable you do not need to determine such configurations. Display logic voltage
come preconfigured on the JILI cable. On occasion backlight voltage has to be adjusted on the cable. Even
though the MOPSlcdLX is a +5V only board you need to supply the +12V for the backlight converter addi-
tionally when using such a converter type.

KTD-S0005-0 Page 15 Graphics Interface
MOPSlcdLX User's Guide
8.2.1 Connector
Header Pin Signal Name Function
1 N.C. Not connected
2 FTX0- First channel data output 0 (negative)
3 FTX0+ First channel data output 0 (positive)
4 ENAVCC Enable panel power
5 FTX1- First channel data output 1 (negative)
6 FTX1+ First channel data output 1 (positive)
7 N.C. Not connected
8 FTX2- First channel data output 2 (negative)
9 FTX2+ First channel data output 2 (positive)
10 GND Ground
11 FTXC- First channel clock output (negative)
12 FTXC+ First channel clock output (positive)
13 GND Ground
14 FTX3- First channel data output 3 (negative)
15 FTX3+ First channel data output 3 (positive)
16 SDA I2C data line
17 STX0- Second channel data output 0 (negative)
18 STX0+ Second channel data output 0 (positive)
19 SCL I2C clock line
20 STX1- Second channel data output 1 (negative)
21 STX1+ Second channel data output 1 (positive)
22 RSVD Reserved
23 STX2- Second channel data output 2 (negative)
24 STX2+ Second channel data output 2 (positive)
25 GND Ground
26 STXC- Second channel clock output (negative)
27 STXC+ Second channel clock output (positive)
28 GND Ground
29 STX3- Second channel data output 3 (negative)
30 STX3+ Second channel data output 3 (positive)
31 - 34 VCC 1) Power +5V
35 BKLTON Backlight on
36 - 37 GND Ground
1
38 - 40 VDD 1) Power +12V if voltage is connected
Note: 1) To protect the external power lines of peripheral devices make sure that
- the wires have the right diameter to withstand the maximum available current.
- to enclosure of the peripheral device fulfills the fire-protecting conditions of IEC/EN 60950.

KTD-S0005-0 Page 16 Graphics Interface
MOPSlcdLX User's Guide
8.3 Connecting a Flat Panel
To determine whether your flat panel is supported check the KONTRON website for panel lists. We regularly
update the list of panels that have been tested with the MOPSlcdLX.
If you use one of those adapters supplied by KONTRON configuration is easy:
Check whether you have the correct adapter and cable for the panel you plan to use. Inspect
the cable for damages. Disconnect the power from your system.
Connect the cable to the flat panel connector X12000 on the MOPSlcdLX and connect the other
end to your JILI adapter - connect the JILI adapter and the display.
 Connect the backlight converter.
Supply power to your system.
If no image appears on your display connect a CRT monitor to the CRT connector.
If necessary program the EEPROM on the JILI cable with the matching configuration data.
If you still do not see improvement consider contacting the dealer for technical support.
8.4 Available Video Modes
The following list shows the video modes supported by the graphics controller with maximum frame buffer
size. When configured for saller frame buffers and/or using a flat panel on the JILI interface not all of the
video modes listed below may be available. Capability depends on system configuration and on display
capabilities. Different operating systems also may not support all listed modes by the available drivers.
Video Mode Type Characters/Pixels Colors
00h/01h Text 40 x 25 16
02h/03h Text 80 x 25 16
04h/05h Graphic 320 x 200 4
06h Graphic 640 x 200 2
07h Text 80 x 25 2
0Dh Graphic 320 x 200 16
0Eh Graphic 640 x 200 16
0Fh Graphic 640 x 350 2
10h Graphic 640 x 350 4
11h Graphic 640 x 480 2
12h Graphic 640 x 480 16
13h Graphic 320 x 200 256