Kontron X-Board UPA 63036 User manual

Kontron Embedded Modules GmbH
Flatpanel Solutions
Marschnerstieg 7
22081 Hamburg / Germany
Fon: [phone]
Fax: [phone]
http://www.kontron-emea.com/flatpanel
X-BOARD-UPA
08.09.2004 1
X-BOARD-UPA
Universal Panel Adapter
Part-No. : 63036
Technical Manual (Preliminary!)
Table of Contents
1.0 General Information and Important Notes
2.0 Technical Information Summary
3.0 Configuration
4.0 Connectors
5.0 Layout
6.0 Schematic
7.0 Application Notes
8.0 Technical Specification
9.0 Technical Support
10.0 Revision History

Kontron Embedded Modules GmbH
Flatpanel Solutions
Marschnerstieg 7
22081 Hamburg / Germany
Fon: [phone]
Fax: [phone]
http://www.kontron-emea.com/flatpanel
X-BOARD-UPA
08.09.2004 2
1.0 User Information
Copyright 2004 by Kontron Embedded Modules GmbH, Division Flatpanel
Solutions, Hamburg
In this document Kontron Embedded Modules GmbH, Division Flatpanel
Solutions, Hamburg will also be referred to by the short form “KEM GmbH”.
The information in this document has been carefully checked and is
believed to be accurate and reliable. However, no responsibility is
assumed for inaccuracies. Furthermore, KEM GmbH reserves the right to
make changes to any portion of this manual to improve reliability, function
or design. KEM GmbH does not assume any liability for any product or
circuit described herein.
1.1 Trademarks
AT and IBM are trademarks of International Business Machines.
XT, AT, PS/2 and Personal System/2 are trademarks of International
Business Machines Corporation.
Microsoft is a registered trademark of Microsoft Corporation.
Intel is a registered trademark of Intel Corporation.
All other products and trademarks mentioned in this manual are
trademarks of their respective owners.
The reproduction, transmission or use of this document or its contents is
not permitted without expressed written authority.
Offenders will be liable for damages. All rights created by patent grant or
registration of a utility model or design, are reserved.
1.2 General
For the circuits, descriptions and tables indicated no responsibility is
assumed as far as patents or other rights of third parties are concerned.
The information in the Technical Descriptions describes the type of the
boards and shall not be considered as assured characteristics.
The reproduction, transmission or use of this document or its contents is
not permitted without express written authority. Offenders will be liable for
damages. All rights, including rights created by patent grant or registration
of a utility model or design, are reserved.

Kontron Embedded Modules GmbH
Flatpanel Solutions
Marschnerstieg 7
22081 Hamburg / Germany
Fon: [phone]
Fax: [phone]
http://www.kontron-emea.com/flatpanel
X-BOARD-UPA
08.09.2004 3
1.3 Warranty
Each board is carefully and thoroughly tested before being shipped. If,
however, problems should occur during the operation, please check your
user specific settings of all boards included in your system. This is often
the source of the fault. If a board is defective, it can be sent to your supplier
for repair. Please take care of the following steps:
- The board returned should correspond to the factory default
settings since a test is only possible under these settings.
- In order to repair your board as fast as possible, we require some
additional information from you. Please fill out the attached Repair
Form and include it with the defective board.
- If possible, the board will be upgraded to the latest version without
additional cost.
- Upon receipt of the board, please be aware that your user specific
settings were changes during the test.
Within the guarantee, the repair is free as long as the guarantee conditions
were kept. If no fault has been found, you will be charged with the test cost
due to the high test expenditure. Repairs outside of the guarantee will be
charged.
This KEM GmbH product is warranted against defects in material and
workmanship for our guaranteed warranty period from the date of
shipment. During the warranty period, KEM GmbH will, at its option, either
repair or replace products which prove to be defective.
For warranty service or repair, the product must be returned to a service
facility designated by KEM GmbH.
The foregoing warranty shall not apply to defects resulting from improper or
inadequate maintenance or handling by buyer, unauthorized modification
or misuse, operation outside of the environmental specifications for the
product, or improper installation or maintenance.
KEM GmbH will not be responsible for any defects or damages due to a
faulty KEM GmbH product other than the products supplied by
KEM GmbH.

Kontron Embedded Modules GmbH
Flatpanel Solutions
Marschnerstieg 7
22081 Hamburg / Germany
Fon: [phone]
Fax: [phone]
http://www.kontron-emea.com/flatpanel
X-BOARD-UPA
08.09.2004 4
2.0 Technical Information Summary
X-Board-UPA is an Evaluation Board (only for development) for VGA,
SVGA, XGA type TFT flatpanels to Kontron JILI interface with digital output
option.
CAUTION : Don´t connect this cable to a JILI Interface with LVDS output!
This can cause permanent damage to all connected devices!
3.0 Configuration
The X-Board-UPA is configured with +3,3V DC for the flat panel power
supply and +12V DC for the backlight power supply.
3.1 Configuration SW1
Configuration: Function:
Dip 1 Inverts the Data Enable signal
ON = not invert, OFF = invert
Dip 2 Inverts the V-Sync signal
ON = not invert, OFF = invert
Dip 3 Inverts the Panel Data Clock signal
ON = not invert, OFF = invert
Dip 4 Inverts the H-Sync signal
ON = not invert, OFF = invert
Dip 5 Select Data mapping
ON = U5 active, OFF = U6 active
Dip 6 Not function
3.2 Configuration SW2
Configuration: Function:
Dip 1 Programmable strobe select, only for LVDS output
ON = Rising edge strobe, OFF = Falling edge strobe
Dip 2 Vertical display mode select signal, only for X7
ON = U/D low, OFF = U/D high
Dip 3 Horizontal display mode select signal, only for X7
ON = R/L low, OFF = R/L high
Dip 4 VGA/QVGA mode select signal, only for X7
ON = Q/V low, OFF = Q/V high
Dip 5 Power for serial eeprom (JILI File)
ON = enable eeprom, OFF = disable eeprom
Dip 6 Power for D/A converter (Backlight dimming control, only for X9)
ON = enable D/A converter, OFF = disable D/A converter

Kontron Embedded Modules GmbH
Flatpanel Solutions
Marschnerstieg 7
22081 Hamburg / Germany
Fon: [phone]
Fax: [phone]
http://www.kontron-emea.com/flatpanel
X-BOARD-UPA
08.09.2004 5
3.3 Configuration panel power supply JP1
Only for X3, X6, X7
Configuration: Function:
1-2 shorted +3,3V DC Panel VCC
3-4 shorted + 5V DC Panel VCC
5-6 shorted + 12V DC Panel VCC
7-8 shorted Disable Panel Power Sequencing (only for debugging)
Caution ! Only one configuration (Panel VCC) for flatpanel is allowed,
otherwise the board is permanently damaged.
3.4 Configuration backlight power supply JP1
Only for X3, X9
Configuration: Function:
9-10 + 5V DC Backlight VCC
11-12 +12V DC Backlight VCC
13-14 Disable Backlight Power Sequencing (only for debugging)
Caution ! Only one configuration (Backlight VCC) for Backlight is
allowed, otherwise the board is permanently damaged.

Kontron Embedded Modules GmbH
Flatpanel Solutions
Marschnerstieg 7
22081 Hamburg / Germany
Fon: [phone]
Fax: [phone]
http://www.kontron-emea.com/flatpanel
X-BOARD-UPA
08.09.2004 6
4.0 Connectors
4.1 JILI – Digital Input connector X1
4.2 JILI – Interface connector X2
4.3 JILI40 - Interface connector X3
4.4 DIG30 - Interface connector X6
4.5 FLEX32 – Interface connector X7
4.6 Extern Power input (option) X8
4.7 Backlight connector X9
4.1 JILI – Digital Input connector X1
Flatfoil 40 Contacts, Right Angle, Bottom Contact
Case/Size: 0,5mm Pitch, Series: 6210 / ZIF
Description Name Pin
Pin Name Description
First Line Marker Vsync 1 O O 2 R0 Panel Data R0
Panel Data R1 R1 3 O O 4 ENAVDD Panel power enable
Panel Data R2 R2 5 O O 6 R3 Panel Data R3
Latch pulse Hsync 7 O O 8 R4 Panel Data R4
Panel Data R5 R5 9 O O 10 GND Power Ground
Panel Data G0 G0 11 O O 12 G1 Panel Data G1
Power Ground GND 13 O O 14 G2 Panel Data G2
Panel Data G3 G3 15 O O 16 JILI_DAT I2C Data
Panel Data G4 G4 17 O O 18 G5 Panel Data G5
I2C Clock JILI_CLK 19 O O 20 B0 Panel Data B0
Panel Data B1 B1 21 O O 22 /Detect Panel hot plug detection
Panel Data B2 B2 23 O O 24 B3 Panel Data B3
Power Ground GND 25 O O 26 B4 Panel Data B4
Panel Data B5 B5 27 O O 28 GND Power Ground
Data Clock SCLK 29 O O 30 DE Data Enable
+5,0V DC Power VCC 31 O O 32 VCC +5,0V DC Power
+5,0V DC Power VCC 33 O O 34 VCC +5,0V DC Power
Not connected NC 35 O O 36 GND Power Ground
Power Ground GND 37 O O 38 +12V +12,0V DC Power
+12,0V DC Power +12V 39 O O 40 +12V +12,0V DC Power

Kontron Embedded Modules GmbH
Flatpanel Solutions
Marschnerstieg 7
22081 Hamburg / Germany
Fon: [phone]
Fax: [phone]
http://www.kontron-emea.com/flatpanel
X-BOARD-UPA
08.09.2004 7
4.2 JILI - Interface connector X2
All JILI (JUMPtec Intelligent LVDS Interface ) signals are LVDS
compatible.
Flatfoil 40 Contacts, Right Angle, Bottom Contact
Case/Size: 0,5mm Pitch, Series: 6210 / ZIF
Description Name Pin
Pin Name Description
Not connected NC 1 O O 2 FTX0- Receiver Signal
Receiver Signal FTX0+ 3 O O 4 ENAVDD Panel power enable
Receiver Signal FTX1- 5 O O 6 FTX1+ Receiver Signal
Not connected NC 7 O O 8 FTX2- Receiver Signal
Receiver Signal FTX2+ 9 O O 10 GND Power Ground
Receiver Signal FTXC- 11 O O 12 FTXC+ Receiver Signal
Power Ground GND 13 O O 14 FTX3- Receiver Signal
Receiver Signal FTX3+ 15 O O 16 JILI_DAT I2C Data
Not connected NC 17 O O 18 NC Not connected
I2C Clock JILI_CLK 19 O O 20 NC Not connected
Not connected NC 21 O O 21 NC Not connected
Not connected NC 23 O O 24 NC Not connected
Power Ground GND 25 O O 26 NC Not connected
Not connected NC 27 O O 28 GND Power Ground
Not connected NC 29 O O 30 NC Not connected
+5,0V DC Power VCC 31 O O 32 VCC +5,0V DC Power
+5,0V DC Power VCC 33 O O 34 VCC +5,0V DC Power
Backlight enable /BLON 35 O O 36 GND Power Ground
Power Ground GND 37 O O 38 +12V +12,0V DC Power
+12,0V DC Power +12V 39 O O 40 +12V +12,0V DC Power

Kontron Embedded Modules GmbH
Flatpanel Solutions
Marschnerstieg 7
22081 Hamburg / Germany
Fon: [phone]
Fax: [phone]
http://www.kontron-emea.com/flatpanel
X-BOARD-UPA
08.09.2004 8
4.3 JILI40 – Interface connector X3
All flat screen signals are LVDS compatible
Connector Double Row 2mm, 40 Contacts, Gold plated
Case/Size : Vertical, Through Hole
Matching connector: FCI 90311-040
Description Name Pin
Pin Name Description
Backlight Power SW_BACK 1 O O 2 SW_BACK Backlight Power
Backlight Dimming BRIGHT 3 O O 4 NC Not connected
Not connected NC 5 O O 6 +12V +12,0V DC Power
Not connected NC 7 O O 8 NC Not connected
+12,0V DC Power +12V 9 O O 10 NC Not connected
Not connected NC 11 O O 12 +12V +12,0V DC Power
Not connected NC 13 O O 14 NC Not connected
+12,0V DC Power +12V 15 O O 16 NC Not connected
Not connected NC 17 O O 18 +12V +12,0V DC Power
Receiver Signal FTX3+ 19 O O 20 FTX3- Receiver Signal
Power Ground GND 21 O O 21 GND Power Ground
I2C Clock JILI_CLK 23 O O 24 JILI_DAT I2C Data
Power Ground GND 25 O O 26 FTXC+ Receiver Signal
Receiver Signal FTXC- 27 O O 28 GND Power Ground
Receiver Signal FTX2+ 29 O O 30 FTX2- Receiver Signal
Power Ground GND 31 O O 32 FTX1+ Receiver Signal
Receiver Signal FTX1- 33 O O 34 GND Power Ground
Receiver Signal FTX0+ 35 O O 36 FTX0- Receiver Signal
Power Ground GND 37 O O 38 GND Power Ground
Panel Power SW_VDD 39 O O 40 SW_VDD Panel Power
4.4 DIG30 - Interface connector X6
All flat screen signals are LVTTL compatible (3.3V)
Connector Single Row, 3 Contacts, Case/Size : Right Angle, 1,25mm Pitch
Matching Connector: Hirose DF14-30S-1.25C
Description Name Pin
Pin Name Description
Panel Power SW_VDD 1 O O 2 SW_VDD Panel Power
Power Ground GND 3 O O 4 SCLK Data Clock
Power Ground GND 5 O O 6 Vsync First Line Marker
Latch pulse Hsync 7 O O 8 DE Data Enable
Power Ground GND 9 O O 10 R0 Panel Data R0
Panel Data R1 R1 11 O O 12 R2 Panel Data R2
Panel Data R3 R3 13 O O 14 R4 Panel Data R4
Panel Data R5 R5 15 O O 16 GND Power Ground
Panel Data G0 G0 17 O O 18 G1 Panel Data G1
Panel Data G2 G2 19 O O 20 G3 Panel Data G3
Panel Data G4 G4 21 O O 21 G5 Panel Data G5
Power Ground GND 23 O O 24 B0 Panel Data B0
Panel Data B1 B1 25 O O 26 B2 Panel Data B2
Panel Data B3 B3 27 O O 28 B4 Panel Data B4
Panel Data B5 B5 29 O O 30 GND Power Ground

Kontron Embedded Modules GmbH
Flatpanel Solutions
Marschnerstieg 7
22081 Hamburg / Germany
Fon: [phone]
Fax: [phone]
http://www.kontron-emea.com/flatpanel
X-BOARD-UPA
08.09.2004 9
4.5 FLEX32 - Interface connector X7
All flat screen signals are LVTTL compatible (3.3V)
Flatfoil 32 Contacts, Right Angle, Bottom Contact
Case/Size: 0,5mm Pitch, Series: 6210 / ZIF
Description Name Pin
Pin Name Description
Power Ground GND 1 O O 2 SCLK Data Clock
Latch pulse Hsync 3 O O 4 Vsync First Line Marker
Power Ground GND 5 O O 6 R0 Panel Data R0
Panel Data R1 R1 7 O O 8 R2 Panel Data R2
Panel Data R3 R3 9 O O 10 R4 Panel Data R4
Panel Data R5 R5 11 O O 12 GND Power Ground
Panel Data G0 G0 13 O O 14 G1 Panel Data G1
Panel Data G2 G2 15 O O 16 G3 Panel Data G3
Panel Data G4 G4 17 O O 18 G5 Panel Data G5
Power Ground GND 19 O O 20 B0 Panel Data B0
Panel Data B1 B1 21 O O 21 B2 Panel Data B2
Panel Data B3 B3 23 O O 24 B4 Panel Data B4
Panel Data B5 B5 25 O O 26 GND Power Ground
Data Enable DE 27 O O 28 SW_VDD Panel Power
Panel Power SW_VDD 29 O O 30 R/L Right/Left rotate
Up/Down rotate U/D 31 O O 32 Q/V QVGA/VGA Mode
4.6 Extern Power connector (option) X8
4 Contact Connector, Single Row, Right Angle, Polarization, through hole
Matching Connector: AMP 171822-4
Description Name Pin
Function
+5,0V DC Power VCC 1 O
Power Ground GND 2 O
Power Ground GND 3 O
+12,0V DC Power +12V 4 O
4.7 Backlight connector X9
Apply operating voltage for backlight inverter using
connector X9
Board to Cable Connector, single row, 7 Contacts, Right Angle
Case/Size: 1,25mm Pitch, Matching connector: Molex 51021-0700
Description Name Pin
Function
Not connected NC 1 O Not connected
Backlight Dimming BRIGHT 2 O Analog signal 0V to 4,8V
Power Ground GND 3 O Power Ground
Backlight Power SW_BACK 4 O 5 / 12 V DC (switched) see 3.4
Backlight Power SW_BACK 5 O 5 / 12 V DC (switched) see 3.4
Power Ground GND 6 O Power Grund
Backlight enable ENABKL 7 O Backlight control signal (TTL)

Kontron Embedded Modules GmbH
Flatpanel Solutions
Marschnerstieg 7
22081 Hamburg / Germany
Fon: [phone]
Fax: [phone]
http://www.kontron-emea.com/flatpanel
X-BOARD-UPA
5.0 Layout
08.09.2004 10