Kontron CP6005-SA User manual

D R A F T — F O R I N T E R N A L U S E O N L Y
The pulse of innovation
» User Guide «
CP6005(X)-SA
Doc. ID: 1055-2501, Rev. 1.0
Date: December 20, 2013

D R A F T — F O R I N T E R N A L U S E O N L Y
2
www.kontron.com
User Guide
CP6005(X)-SA
Revision History
Imprint
Kontron Europe GmbH may be contacted via the following:
MAILING ADDRESS TELEPHONE AND E-MAIL
Kontron Europe GmbH +49 (0) 800-SALESKONTRON
Sudetenstraße 7 [email protected]
D - 87600 Kaufbeuren Germany
For further information concerning other Kontron products, please visit our Internet website:
www.kontron.com.
Disclaimer
Copyright © 2013 Kontron AG. All rights reserved. All data is for information purposes only and not
guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate;
however, no responsibility is assumed for inaccuracies. Kontron and the Kontron logo and all other
trademarks or registered trademarks are the property of their respective owners and are recognized.
Specifications are subject to change without notice.
Revision Brief Description of Changes Date of Issue
1.0 Initial issue 20-Dec-2013

D R A F T — F O R I N T E R N A L U S E O N L Y
3
www.kontron.com
User Guide
CP6005(X)-SA
Contents
Revision History ..........................................................................................................2
Imprint .....................................................................................................................2
Disclaimer ..................................................................................................................2
Contents ....................................................................................................................3
Tables .......................................................................................................................7
Figures ......................................................................................................................9
Warranty .................................................................................................................. 10
Proprietary Note ........................................................................................................ 10
Trademarks .............................................................................................................. 10
Environmental Protection Statement .............................................................................. 10
1 Introduction ...................................................................................... 11
1.1 Board Overview .......................................................................................... 11
1.2 System Expansion Capabilities ....................................................................... 12
1.2.1 PMC Module ............................................................................................... 12
1.2.2 XMC Module ............................................................................................... 12
1.2.3 CP6005(X)-SA-MK2.5SATA Assembly Kit ........................................................... 12
1.2.4 SATA Flash Module ...................................................................................... 12
1.2.5 Rear I/O Module ......................................................................................... 12
1.3 Board Diagrams.......................................................................................... 13
1.3.1 Functional Block Diagram ............................................................................. 13
1.3.2 Front Panel ............................................................................................... 14
1.3.3 Board Layout ............................................................................................. 15
1.4 Technical Specification ................................................................................ 18
1.5 Standards ................................................................................................. 23
1.6 Related Publications.................................................................................... 24
2 Functional Description ......................................................................... 25
2.1 Processor and Chipset.................................................................................. 25
2.1.1 Integrated Processor Graphics Controller ......................................................... 26
2.2 Memory .................................................................................................... 26
2.3 Watchdog Timer.......................................................................................... 26
2.4 Battery..................................................................................................... 26
2.5 Flash Memory............................................................................................. 27
2.5.1 SPI Boot Flash for uEFI BIOS.......................................................................... 27
2.5.2 SATA Flash Module ...................................................................................... 27
2.6 Trusted Platform Module 1.2.......................................................................... 27
2.7 Board Interfaces......................................................................................... 28
2.7.1 Front Panel LEDs......................................................................................... 28
2.7.1.1 Watchdog and Temperature Status LEDs .......................................................... 28

D R A F T — F O R I N T E R N A L U S E O N L Y
4
www.kontron.com
User Guide
CP6005(X)-SA
2.7.1.2 IPMI LEDs and HS LED .................................................................................. 29
2.7.1.3 General Purpose LEDs.................................................................................. 29
2.7.2 USB Interfaces ........................................................................................... 31
2.7.3 VGA Interface ............................................................................................ 31
2.7.4 Serial Ports ............................................................................................... 32
2.7.5 Gigabit Ethernet ......................................................................................... 32
2.7.5.1 10 Gigabit Ethernet Interfaces (CP6005X-SA) .................................................... 33
2.7.6 SATA Interfaces .......................................................................................... 33
2.7.7 PMC Interface ............................................................................................ 33
2.7.8 XMC Interface ............................................................................................ 34
2.7.9 CompactPCI Interface .................................................................................. 34
2.7.9.1 Board Functionality when Installed in System Slot.............................................. 34
2.7.9.2 Board Functionality when Installed in System Slot.............................................. 34
2.7.9.3 Board Functionality when Installed in Peripheral Slot (Passive Mode) ..................... 35
2.7.9.4 Packet Switching Backplane (PICMG 2.16) ........................................................ 35
2.7.9.5 Hot Swap Support ....................................................................................... 35
2.7.9.6 Power Ramping .......................................................................................... 35
2.7.9.7 Precharge ................................................................................................. 35
2.7.9.8 Handle Switch............................................................................................ 35
2.7.9.9 ENUM# Interrupt ........................................................................................ 35
2.7.9.10 Hot Swap LED............................................................................................. 35
2.7.10 CompactPCI Connectors ............................................................................... 36
2.7.10.1 Connector Keying ....................................................................................... 36
2.7.10.2 CompactPCI Connectors J1 and J2 Pinout ......................................................... 37
2.7.10.3 CompactPCI Rear I/O Connectors J3 and J5 Pinout.............................................. 40
2.7.10.4 High-Speed Serial Rear I/O Connectors J41 and J4 Pinout (CP6005X-SA) ................. 43
2.7.11 High-Speed Serial Rear I/O Interconnection ..................................................... 45
3 Configuration..................................................................................... 46
3.1 DIP Switch Configuration.............................................................................. 46
3.1.1 DIP Switch SW1 .......................................................................................... 46
3.1.2 DIP Switch SW2 .......................................................................................... 46
3.2 System Write Protection ............................................................................... 47
3.3 CP6005(X)-SA-Specific Registers .................................................................... 47
3.3.1 Write Protection Register (WPROT) .................................................................. 47
3.3.2 Reset Status Register (RSTAT) ........................................................................ 48
3.3.3 Board ID High Byte Register (BIDH) ................................................................ 49
3.3.4 Geographic Addressing Register (GEOAD) ......................................................... 49
3.3.5 Watchdog Timer Control Register (WTIM) ......................................................... 50
3.3.6 Board ID Low Byte Register (BIDL).................................................................. 51
3.3.7 LED Configuration Register (LCFG) .................................................................. 51
3.3.8 LED Control Register (LCTRL) ......................................................................... 52
3.3.9 General Purpose Output Register (GPOUT)......................................................... 53
3.3.10 General Purpose Input Register (GPIN)............................................................ 53
4 Power Considerations .......................................................................... 54

D R A F T — F O R I N T E R N A L U S E O N L Y
5
www.kontron.com
User Guide
CP6005(X)-SA
4.1.1 Start-Up Requirement.................................................................................. 54
4.1.2 Power-Up Sequence..................................................................................... 54
4.1.3 Regulation ................................................................................................ 55
4.2.1 Power Consumption of the CP6005(X)-SA Accessories .......................................... 58
4.2.2 Power Consumption per Gigabit Ethernet Port ................................................... 58
4.2.3 Power Consumption per 10 Gigabit Ethernet Port (CP6005X-SA)............................. 58
4.2.4 Power Consumption of PMC Module ................................................................. 58
4.2.5 Power Consumption of XMC Modules ................................................................ 59
5 Thermal Considerations ........................................................................ 60
5.1 Operational Limits for the CP6005(X)-SA .......................................................... 61
5.1.1 Peripherals ............................................................................................... 63
6 CP6005(X)-SA-MK2.5-SATA Assembly Kit ................................................. 64
6.1 MMADP-SATA01 Module Overview.................................................................... 64
6.2 Technical Specifications ............................................................................... 64
6.3 MMADP-SATA01 Module Layout ...................................................................... 64
7 SATA Flash Module............................................................................... 65
7.1 Technical Specifications ............................................................................... 65
7.2 SATA Flash Module Layout............................................................................. 65
8 Installation ....................................................................................... 66
8.1 Safety ...................................................................................................... 66
8.2 General Instructions on Usage ....................................................................... 66
8.3 Board Installation ...................................................................................... 67
8.3.1 Hot Swap Insertion..................................................................................... 67
8.3.2 Hot Swap Removal ...................................................................................... 67
8.4 Installation of Peripheral Devices ................................................................... 68
8.4.1 SATA Flash Module Installation ...................................................................... 69
8.4.2 Installation of External SATA Devices .............................................................. 69
8.4.3 Onboard 2.5” HDD/SSD Installation ................................................................ 69
8.4.4 PMC Module Installation ............................................................................... 69
8.4.5 XMC Module Installation ............................................................................... 69
8.4.6 Rear Transition Module Installation ................................................................ 69
8.5 Battery Replacement ................................................................................... 69
9 uEFI BIOS .......................................................................................... 70
9.1 Starting the uEFI BIOS ................................................................................. 70
9.2 Setup Menus.............................................................................................. 71
9.2.1 Main Setup Menu ........................................................................................ 71
9.2.2 Advanced Setup Menu .................................................................................. 72
9.2.3 Security Setup Menu.................................................................................... 72
9.2.3.1 Remember the Password ............................................................................... 73
9.2.4 Boot Setup Menu ........................................................................................ 73

D R A F T — F O R I N T E R N A L U S E O N L Y
6
www.kontron.com
User Guide
CP6005(X)-SA
9.2.5 Exit Setup Menu ......................................................................................... 73
9.3 The uEFI Shell ............................................................................................ 74
9.3.1 Introduction, Basic Operation ....................................................................... 74
9.3.1.1 Entering the uEFI Shell ................................................................................ 74
9.3.1.2 Exiting the uEFI Shell .................................................................................. 74
9.3.2 Kontron-Specific uEFI Shell Commands ............................................................ 75
9.4 uEFI Shell Scripting..................................................................................... 76
9.4.1 Startup Scripting ........................................................................................ 76
9.4.2 Create a Startup Script ................................................................................. 76
9.4.3 Examples of Startup Scripts........................................................................... 77
9.4.3.1 Execute Shell Script on Other Harddrive ........................................................... 77
9.4.3.2 Enable Watchdog ........................................................................................ 77
9.4.3.3 Handling the Startup Script in the SPI Boot Flash ............................................... 77
9.5 Firmware Update ........................................................................................ 78
9.5.1 Updating the uEFI BIOS................................................................................ 78
9.5.1.1 uEFI BIOS Fail-Over Mechanism ...................................................................... 78
9.5.1.2 Updating Procedure .................................................................................... 78
9.5.1.3 uEFI BIOS Recovery ..................................................................................... 79
9.5.1.4 Determining the Active Flash......................................................................... 79
9.5.2 Updating the IPMI Firmware .......................................................................... 79
9.5.2.1 IPMI Rollback Mechanism ............................................................................. 79
9.5.2.2 Determining the Active IPMI Firmware Image .................................................... 79
9.5.2.3 Updating Procedure .................................................................................... 79
10 IPMI Firmware .................................................................................... 80
10.1 Overview................................................................................................... 80
10.2 IPMI Firmware and KCS Interface Configuration ................................................. 81
10.3 Supported IPMI and ATCA Commands ............................................................... 81
10.3.1 Standard IPMI Commands ............................................................................ 81
10.3.2 AdvancedTCA and AMC Commands ................................................................... 84
10.4 Firmware Identification................................................................................ 85
10.4.1 Get Device ID Command ............................................................................... 85
10.4.2 Device Locator Record.................................................................................. 86
10.5 Board Control Extensions ............................................................................. 86
10.5.1 SPI Boot Flash Selection—uEFI BIOS Failover Control .......................................... 86
10.5.2 uEFI BIOS Boot Order Selection ...................................................................... 86
10.5.3 Set Control State (SPI Boot Flash Selection, Boot Order Selection)......................... 87
10.5.4 Get Control State (SPI Boot Flash Selection, Boot Order Selection)......................... 88
10.6 Sensors Implemented on the Board................................................................. 89
10.6.1 Sensor List ................................................................................................ 89
10.7 Sensor Thresholds....................................................................................... 92
10.8 OEM Event/Reading Types ............................................................................. 93
10.9 IPMI Firmware Code..................................................................................... 94
10.9.1 Firmware Upgrade....................................................................................... 94
10.9.2 IPMI Firmware and FRU Data Write Protection .................................................... 94
10.10 LAN Functions............................................................................................ 94

D R A F T — F O R I N T E R N A L U S E O N L Y
7
www.kontron.com
User Guide
CP6005(X)-SA
Tables
1 CP6005(X)-SA Main Specifications ......................................................................... 18
2 Standards ........................................................................................................ 23
3 Additional Standards for Boards Ordered with Ruggedized Service ................................. 23
4 Related Publications ........................................................................................... 24
5 Features of the Processors Supported on the CP6005(X)-SA ......................................... 25
6 Watchdog and Temperature Status LEDs’ Functions .................................................... 28
7 IPMI and HS LEDs’ Functions ................................................................................. 29
8 General Purpose LEDs’ Functions on the CP6005-SA ................................................... 30
9 General Purpose LEDs’ Functions on the CP6005X-SA .................................................. 30
10 POST Code Sequence ........................................................................................... 31
11 POST Code Example ............................................................................................. 31
12 Serial Port Connector J8 Pinout ............................................................................. 32
13 Gigabit Ethernet Controller Port Mapping ................................................................ 32
14 10 Gigabit Ethernet Controller Port Mapping ............................................................ 33
15 PMC PCI Frequency Configuration ........................................................................... 33
16 CompactPCI PCI/PCI-X Configuration ..................................................................... 34
22 CompactPCI Rear I/O Connector J3 Signals ............................................................... 41
24 CompactPCI Rear I/O Connector J5 Signals ............................................................... 42
27 High-Speed Serial Rear I/O Connectors J41 and J4 Signal Description ............................ 44
28 High-Speed Serial Rear I/O Interconnection Port Mapping ........................................... 45
29 DIP Switch SW1 Functionality ................................................................................ 46
30 DIP Switch SW2 Functionality ................................................................................ 46
31 CP6005(X)-SA-Specific Registers ........................................................................... 47
32 Write Protection Register (WPROT) ......................................................................... 47
33 Reset Status Register (RSTAT) ............................................................................... 48
34 Board ID High Byte Register (BIDH) ....................................................................... 49
35 Geographic Addressing Register (GEOAD) ................................................................ 49
36 Watchdog Timer Control Register (WTIM) ................................................................. 50
37 Board ID Low Byte Register (BIDL) ......................................................................... 51
38 LED Configuration Register (LCFG) ......................................................................... 51
39 LED Control Register (LCTRL) ................................................................................ 52
40 General Purpose Output Register (GPOUT) ................................................................ 53
41 General Purpose Input Register (GPIN) .................................................................... 53
42 DC Operational Input Voltage Range ....................................................................... 54
43 Workload: uEFI Shell ........................................................................................... 57
44 Workload: Idle .................................................................................................. 57
45 Workload: Typical ............................................................................................... 57
46 Workload: Maximum ........................................................................................... 57
47 Power Consumption of CP6005(X)-SA Accessories ...................................................... 58
48 Power Consumption per Gigabit Ethernet Port ........................................................... 58
49 Power Consumption per 10 Gigabit Ethernet Port ....................................................... 58
50 PMC Module Current ............................................................................................ 58
51 XMC Module Current ............................................................................................ 59
52 MMADP-SATA01 Main Specifications ....................................................................... 64
53 SATA Flash Module Main Specifications ................................................................... 65

D R A F T — F O R I N T E R N A L U S E O N L Y
8
www.kontron.com
User Guide
CP6005(X)-SA
54 Navigation ....................................................................................................... 70
55 Main Setup Menu Sub-Screens and Functions ............................................................ 71
56 Advanced Setup Menu Sub-Screens and Functions ..................................................... 72
57 Security Setup Menu Functions .............................................................................. 72
58 TPM Configuration Sub-Screen .............................................................................. 72
59 Boot Priority Order ............................................................................................. 73
60 Exit Setup Menu Functions ................................................................................... 73
61 Kontron-Specific uEFI Shell Commands ................................................................... 75

D R A F T — F O R I N T E R N A L U S E O N L Y
9
www.kontron.com
User Guide
CP6005(X)-SA
Figures
1 CP6005(X)-SA Functional Block Diagram ................................................................ 13
2 4 HP CP6005(X)-SA Front Panel ............................................................................ 14
3 4 HP CP6005-SA Board Layout (Top View) ............................................................... 15
4 4 HP CP6005X-SA Board Layout (Top View) .............................................................. 16
5 4 HP CP6005(X)-SA Board Layout (Bottom View) ...................................................... 17
6 Serial Port Connector J8 ..................................................................................... 32
7 CompactPCI Connectors ...................................................................................... 36
8 CP6005(X)-SA with Core™ i7-4860EQ (SV), 1.8 GHz ................................................... 61
9 CP6005(X)-SA with Core™ i7-4700EQ (SV), 2.4 GHz ................................................... 61
10 CP6005(X)-SA with Core™ i7-4700EQ (SV), 1.7 GHz ................................................... 62
11 CP6005(X)-SA with Core™ i5-4400E (SV), 2.7 GHz ..................................................... 62
12 MMADP-SATA01 Module Layout ............................................................................. 64
13 SATA Flash Module Layout (Bottom View) ............................................................... 65
14 Connecting a Peripheral Device to the CP6005X-SA ................................................... 68

D R A F T — F O R I N T E R N A L U S E O N L Y
10
www.kontron.com
User Guide
CP6005(X)-SA
Warranty
This Kontron product is warranted against defects in material and workmanship for the warranty period
from the date of shipment. During the warranty period, Kontron will at its discretion decide to repair
or replace defective products.
Within the warranty period, the repair of products is free of charge as long as warranty conditions are
observed.
The warranty does not apply to defects resulting from improper or inadequate maintenance or handling
by the buyer, unauthorized modification or misuse, operation outside of the product’s environmental
specifications or improper installation or maintenance.
Kontron will not be responsible for any defects or damages to other products not supplied by Kontron
that are caused by a faulty Kontron product.
Proprietary Note
This document contains information proprietary to Kontron. It may not be copied or transmitted by any
means, disclosed to others, or stored in any retrieval system or media without the prior written consent
of Kontron or one of its authorized agents.
The information contained in this document is, to the best of our knowledge, entirely correct. Howev-
er, Kontron cannot accept liability for any inaccuracies or the consequences thereof, or for any liability
arising from the use or application of any circuit, product, or example shown in this document.
Kontron reserves the right to change, modify, or improve this document or the product described here-
in, as seen fit by Kontron without further notice.
Trademarks
This document may include names, company logos and trademarks, which are registered trademarks
and, therefore, proprietary to their respective owners.
Environmental Protection Statement
This product has been manufactured to satisfy environmental protection requirements where possible.
Many of the components used (structural parts, printed circuit boards, connectors, batteries, etc.) are
capable of being recycled.
Final disposition of this product after its service life must be accomplished in accordance with appli-
cable country, state, or local laws or regulations.

D R A F T — F O R I N T E R N A L U S E O N L Y
11
www.kontron.com
User Guide
CP6005(X)-SA
1 Introduction
1.1 Board Overview
The CP6005(X)-SA is a highly integrated 6U CompactPCI® processor board based on the 4th genera-
tion Intel® Core™ i7/i5 processor in combination with the Intel® QM87 Chipset. The CP6005-SA is a
fully-compliant PICMG 2.16 processor board whereas the CP6005X-SA offers additional dual 10 Giga-
bit Ethernet and PCI Express to the backplane.
With the powerful, 4th generation quad-core Intel® Core™ i7 and dual-core Intel® Core™ i5 proces-
sors, the CP6005(X)-SA offers extraordinary performance-per-watt values and is an ideal backbone for
powerful network-intensive applications providing virtualization (VT-X, VT-D) and highest graphics
performance. The new-generation graphics controller has up to 40 execution units providing OpenCL
1.2/ OpenGL 4.0 and triple independent display support. Five Gigabit Ethernet channels on the
CP6005-SA provide well-weighted data throughput for external and internal PICMG® 2.16-compliant
Ethernet traffic. The CP6005X-SA supports two additional 10 Gigabit Ethernet ports combined with x4
PCI Express® 2.0 via a rear I/O ZDplus connector, all based on PICMG® 2.20 for high bandwidth
requirements.
The Intel® Advanced Vector Extensions AVX 2.0 enhancements provide a huge performance improve-
ment in floating-point-intensive computations, which are a key part of digital signal and image pro-
cessing applications such as medical imaging and radar or sonar.
Both PICMG 2.16-compliant CP6005-SA and CP6005X-SA processor boards offer up to 16 GB dual-
channel 1600 MHz DDR3L ECC memory via two SODIMM sockets providing up to 25 GB/sec data
throughput. Thanks to hot swap support and IPMI (PICMG 2.9-compliant Intelligent Platform Manage-
ment Interface), the CPU board meets the highest demands for the management of high-availability
applications. Many of these are data and telecommunications applications also including highly sen-
sitive security-related solutions as well as image processing systems.
The Intel® QM87 Chipset provides advanced I/O technology including USB and Serial ATA channels for
an onboard 2.5-inch SATA hard disk or SSD and an industrial-grade NAND Flash SSD
device—all usable in a 4HP single slot. The highly integrated CP6005(X)-SA features also an XMC site
according to XMC.3 supporting x8 PCI Express® (alternatively a 32-bit/66 MHz PCI PMC site) for vari-
ous market available extensions. Based on the Kontron rear I/O concept, existing rear transition
modules are fully functional on the CP6005-SA, where the CP6005X-SA provides additional 10 GbE and
PCI Express on the backplane for communication between CompactPCI® slots. Appropriate backplanes
and systems are available.
Delivering a stable product based on Intel®‘s embedded product line, the CP6005(X)-SA ensures long
term availability. This eliminates the risk of unplanned design changes and unexpected expensive
application modification. While minimizing deployment risks, the CP6005(X)-SA provides a broad
range of software support to ease the process of product integration and maximize the competitive
advantage of meeting the time-to-market window.
The board is offered with various board support packages including Windows, VxWorks and Linux oper-
ating systems. For further information concerning the operating systems available for the CP6005(X)-
SA, please contact Kontron.

D R A F T — F O R I N T E R N A L U S E O N L Y
12
www.kontron.com
User Guide
CP6005(X)-SA
1.2 System Expansion Capabilities
1.2.1 PMC Module
The CP6005(X)-SA has a 3.3 V, PMC mezzanine interface configurable for 32-bit /66 MHz PCI operation.
This interface supports a wide range of PMC modules with PCI interface including all of Kontron’s PMC
modules and provides an easy and flexible way to configure the CP6005(X)-SA for various application
requirements. For information on the PMC interface, refer to Chapter 2.7.7, "PMC Interface".
1.2.2 XMC Module
The CP6005(X)-SA has one XMC mezzanine interface for support of x1, x4 and x8 PCI Express 2.0 XMC
modules providing an easy and flexible way to configure the CP6005(X)-SA for various application re-
quirements. For information on the XMC interface, refer to Chapter 2.7.8, "XMC Interface".
1.2.3 CP6005(X)-SA-MK2.5SATA Assembly Kit
The CP6005(X)-SA comes with an optional CP6005(X)-SA-MK2.5SATA assembly kit comprised of one
MMADP-SATA01 module and the necessary components needed for mounting the module on the
CP6005(X)-SA. The MMADP-SATA01 module is required for connecting an onboard 2.5" SATA HDD or
SSD to the CP6005(X)-SA via an onboard SATA extension connector. For further information concern-
ing the MMADP-SATA01 module, refer to Chapter 6.
1.2.4 SATA Flash Module
The CP6005(X)-SA provides support for up to 64 GB NAND flash memory in combination with an option-
al SATA Flash module, which is connected to the CP6005(X)-SA via an onboard SATA extension connec-
tor. For further information concerning the SATA Flash module, refer to Chapter 7.
1.2.5 Rear I/O Module
The CP6005(X)-SA provides support for one rear I/O module via the CompactPCI rear I/O connectors.
For further information about the compatibility of rear I/O modules with the CP6005(X)-SA, refer to
the CP6005(X)-SA datasheet.

D R A F T — F O R I N T E R N A L U S E O N L Y
13
www.kontron.com
User Guide
CP6005(X)-SA
1.3 Board Diagrams
The following diagrams provide additional information concerning board functionality and component
layout.
1.3.1 Functional Block Diagram
Figure 1: CP6005(X)-SA Functional Block Diagram
Front Panel
cPCI
2x
USB
Debug
DMI 2.0
4x
USB 2.0
4x
SATA
Temp. Sense
GbE PCI 64/66 MHz
3.3V / 5V VIO
TH/
WD
HS
IPMB
COMA
RJ-45
Hot
Swap
2.5" SATA
HDD/SSD or
SATA Flash
Module
VGA CRT
1000BT
RJ-45
PCI 32-bit / 66MHz
Mag.
DDR3L w ECC
SODIMM
memory
Channel A
4th Gen.
Intel®
Core™ i7/i5
DDR3L DDR3L
Intel®
QM87
PCH DMI
SMB
SPI
PCIe
FDI XDP
FDI x2
PCI 64-bit
DP to
HDMI /
DVI
2x
HDMI/DVI
2xDDI
USB 2.0
SATA Cable
Conn.
SATA HDA
HDA
DDR3L w ECC
SODIMM
memory
Channel B
PCIe
to
PCI
Mag.
1000BT
RJ-45
PMC/XMC
PCI 32-bit/66MHz
XMC PCIe x8
VGA
CRT
RST
IPMI 1000BT
RJ-45
Mag.
Rear I/O
RS-
232
COMA
GbE
Intel®
I210-IT
dual
10GBASE-KR
Intel® 82599ES
FPGA
Board
Control
EEP
PCIe
x2
TPM
LPC LPC
LEDs
Front I/O
I2C
GP
DMI
FDI
PCIe PCIe
Bat.
RTC
Intel® I350
Quad GbE
Intel® I350
PCIe
PCIe
PCIe
x1
GbE
USB 2.0 PCIe
Mag.
PCIe
x4
COMB
RS-422 or
RS-232
GPIO
3.3V
IPMI
Controller
PCIe
Mag.
1600 MHz
Rear I/O
Rear I/O
PCIe
x2
PCIe
x4
J4 PICMG 2.20
2x 10GBASE-KR 1x PCIe x4
J3 PICMG 2.16
VGA
CRT
PCIe
to
PCI
dual
UART
SMB
VGA
Switch
VGA
Switch
PCIe
x4
PCIe x8
SPI Boot
Flashes
(standard/
recovery)
CP6005X-SA

D R A F T — F O R I N T E R N A L U S E O N L Y
14
www.kontron.com
User Guide
CP6005(X)-SA
1.3.2 Front Panel
Figure 2: 4 HP CP6005(X)-SA Front Panel
SP ACT
GbE E SP ACT
GbE B ACTGbE A
TH 0 WD 1
I0 2 I1 3
PMC/XMC VGA COM
USB 2.0 RST
HS
IPMI LEDs
I0/I1 (red/green): Indicate the software status of the IPMI controller
System Status LEDs
HS (blue): Hot Swap Status
TH (red/green): Temperature Status
WD (green): Watchdog Status
General Purpose LEDs
LED3–0 (red/green/amber): General Purpose/POST Code
Note: If the General Purpose LEDs 3–0 are lit red during boot-up,
a failure is indicated before the uEFI BIOS has started.
Integral Ethernet LEDs
ACT (green): Ethernet Link/Activity
SPEED (orange): 1000BASE-T Ethernet Speed
SPEED (green): 100BASE-TX Ethernet Speed
SPEED (off) + ACT (on): 10BASE-T Ethernet Speed

D R A F T — F O R I N T E R N A L U S E O N L Y
15
www.kontron.com
User Guide
CP6005(X)-SA
1.3.3 Board Layout
Figure 3: 4 HP CP6005-SA Board Layout (Top View)
4th Gen.
Intel® Core™ i7/i5
Battery
J12
GbE E
J11
GbE B
J10
GbE A
J14
J16
J15
IPMI/WD/TH LEDs
GP/POST CODE LEDs
J17
J18
J19
J5
J3
J2
J1
J13
J6
HS LED
J7
J8
J9
J20 J21
Intel® QM87
SATA Flash Module
MMADP-
SATA01
Module
Intel®
I350 Magnetics
Magnetics
HDD/SSD
PMC/XMC

D R A F T — F O R I N T E R N A L U S E O N L Y
16
www.kontron.com
User Guide
CP6005(X)-SA
Figure 4: 4 HP CP6005X-SA Board Layout (Top View)
4th Gen.
Intel® Core™ i7/i5
Battery
J12
GbE E
J11
GbE B
J10
GbE A
J14
J16
J15
IPMI/WD/TH LEDs
GP/POST CODE LEDs
J17
J18
J19
J5
J41
J4
J3
J2
J1
J13
J6
HS LED
J7
J8
J9
J20 J21
Intel® QM87
SATA Flash Module
MMADP-
SATA01
Module
Intel® 82599ES
Intel®
I350 Magnetics
Magnetics
10GbE
Controller
HDD/SSD
PMC/XMC

D R A F T — F O R I N T E R N A L U S E O N L Y
17
www.kontron.com
User Guide
CP6005(X)-SA
Figure 5: 4 HP CP6005(X)-SA Board Layout (Bottom View)
ON
4
3
2
1
4
3
2
1
ON
SW2
J25
SW1

D R A F T — F O R I N T E R N A L U S E O N L Y
18
www.kontron.com
User Guide
CP6005(X)-SA
1.4 Technical Specification
Table 1: CP6005(X)-SA Main Specifications
FEATURES SPECIFICATIONS
Processor & Chipset
CPU & Graphics Controller The CP6005(X)-SA supports the following 4th generation processors:
» Quad-core Intel® Core™ i7-4860EQ (SV), 1.8 GHz, 6 MB L3 cache, GT3e, In-
tel® Iris™ Pro Graphics 5200
» Quad-core Intel® Core™ i7-4700EQ (SV), 2.4 GHz, 6 MB L3 cache, GT2, Intel®
HD Graphics 4600
» Dual-core Intel® Core™ i5-4400E (SV), 2.7 GHz, 3 MB L3 cache, GT2, Intel®
HD Graphics 4600
PCH Intel® QM87 Chipset
Memory
Main Memory Up to 16 GB, dual-channel DDR3 SDRAM memory with ECC running at 1600 MHz on
two SODIMM sockets
Flash Memory Two 16 MB SPI boot flash chips for two separate uEFI BIOS images
Up to 64 GB SLC NAND flash via an onboard SATA Flash module (SSD)
EEPROM EEPROM with 64 kbit
Interfaces
CompactPCI CompactPCI interface:
» Compliant with CompactPCI Specification PICMG 2.0 R 3.0:
» System controller operation
» 64-bit/ 66 MHz PCI or PCI-X master interface with dedicated PCIe-to-PCI-
X bridge
» 3.3V or 5V signaling levels (universal signaling support)
» Compliant with the Packet Switching Specification PICMG 2.16.
The CP6005(X)-SA supports System Master hot swap functionality and applica-
tion-dependent hot swap functionality when used in a peripheral slot.
When used as a System Master, the CP6005(X)-SA supports individual clocks for
each slot and the ENUM signal handling is in compliance with the PICMG 2.1 Hot
Swap Specification.
When installed in a peripheral slot, the CP6005(X)-SA is isolated from the Com-
pactPCI bus. It receives power from the backplane and supports rear I/O and, if
the system supports it, packet switching (in this case up to two channels of Giga-
bit Ethernet).
Standard Rear I/O The following interfaces are routed to the rear I/O connectors J3 and J5.
COMA (RS-232 signaling) and COMB (RS-232 signaling); no buffer on the rear I/O
module is necessary
»4xUSB2.0
» 1 x CRT VGA, 2 x HDMI/DVI
»1xHDA
» 2 x Gigabit Ethernet (compliant with PICMG 2.16, R 1.0)
»4xSATA3Gb/s
» 4 x GPIs and 4 GPOs (LVTTL signaling)
» System write protection

D R A F T — F O R I N T E R N A L U S E O N L Y
19
www.kontron.com
User Guide
CP6005(X)-SA
Interfaces
High-Speed Serial Rear
I/O Interconnection
(CP6005X-SA)
The following interfaces are provided on the rear I/O via two ZDplus high-speed
connectors, J4 and J41 (PICMG 2.20):
» Two 10GBASE-KR interfaces
» One x4 PCI Express 2.0 operating at 5 GT/s as a root complex controller only
The port mapping of the high-speed serial rear I/O interconnection on the
CP6005(X)-SA is capable of supporting two 10GBASE-KR/40GBASE-KR4 inter-
faces, one x8 PCI Express 3.0 operating at 8 GT/s, and two SATA 6 Gb/s ports.
However, the current implementation provides support for only two 10GBASE-KR
and one x4 PCI Express 2.0 operating at 5 GT/s.
10 Gigabit Ethernet
(CP6005X-SA)
Two 10GBASE-KR interfaces for high-speed serial rear I/O interconnection based
on the Intel® 82599ES dual-port 10 Gigabit Ethernet controller
Gigabit Ethernet Five 10 Base-T/100 Base-TX/1000 Base-T Gigabit Ethernet interfaces based on
one Intel® I210-IT Gigabit Ethernet controller and one Intel® I350 quad-port
Gigabit Ethernet controller:
» Three RJ-45 connectors on the front panel
» Two ports on the rear I/O (PICMG 2.16)
USB Six USB ports supporting UHCI (USB 1.1) and EHCI (USB 2.0):
» Two type A USB 2.0 connectors on the front panel
» Four USB 2.0 ports on the rear I/O interface
Serial Two 16C550-compatible UARTs:
» One RS-232 port on the front panel and routed to rear I/O, COMA
» One RS-232 port on the rear I/O, COMB
XMC XMC interface:
» One onboard XMC connector for connecting a standard XMC module
» Up to x8 PCI Express 2.0 ports operating at 5 GT/s
(up to x8 PCI Express 3.0 operating at 8 GT/s on request)
SATA » Two SATA 6 Gb/s interfaces for:
» Up to 64 GB flash memory via an onboard SATA Flash module, or
» Onboard 2.5" HDD / SSD is supported in combination with the MMADP-
SATA01 module
» One standard SATA 6 Gb/s interface for the standard SATA connector
» Four SATA 3 Gb/s ports accessible via rear I/O
» High-performance RAID 0/1/5/10 functionality on all SATA ports
Sockets
Front Panel Connectors » VGA: one 15-pin, D-Sub connector, J9
» USB: two 4-pin, type A connectors, J6 and J7
» Ethernet: three 8-pin, RJ-45 connectors, J10, J11 and J12
» Serial port: one 8-pin, RJ-45 connector, J8 (COMA)
» XMC front panel bezel cutout
Table 1: CP6005(X)-SA Main Specifications (Continued)
FEATURES SPECIFICATIONS

D R A F T — F O R I N T E R N A L U S E O N L Y
20
www.kontron.com
User Guide
CP6005(X)-SA
Sockets
Onboard Connectors » One XMC connector, J19 (P15)
» Two SATA connectors
» One 7-pin, standard SATA connector, J14
» One 34-pin, SATA extension connector, J16
» One JTAG connector, J15
» One XDP-SFF (debug) connector, J25
» Four CompactPCI connectors J1, J2, J3 and J5
» Two ZDplus high-speed serial rear I/O connectors, J4 and J41 (PICMG 2.20)
(CP6005X-SA)
» Two 204-pin DDR3L SODIMM sockets, J17 and J18
LEDs
Front Panel LEDs IPMI LEDs:
» I0/I1 (red/green): Software status of the IPMI controller
System Status LEDs:
» WD (green): Watchdog status
» TH (red/green): Temperature status
» HS (blue): Hot swap status
General Purpose LEDs:
» LED3–0 (red/green/amber): General purpose / POST code
Ethernet LEDs:
» ACT (green): Network link / activity
» SPEED (green/orange): Network speed
Switches
DIP Switches Two onboard DIP switches, SW1 and SW2 for board configuration on the rear side
of the board
Reset Switch One hardware reset switch on the front panel
Hot Swap Switch One switch for hot swap purposes integrated in the front panel in accordance
with PICMG 2.1 Rev. 2.0
Timer
Real-Time Clock Real-time clock with 256 Byte CMOS RAM; battery-backup available
Watchdog Timer Software-configurable, two-stage Watchdog with programmable timeout ranging
from 125 ms to 4096 s in 16 steps
Serves for generating IRQ or hardware reset
System Timer The Intel® QM87 Chipset contains three 8254-style counters with fixed uses.
In addition to the three 8254-style counters, the Intel® QM87 Chipset includes
eight individual high-precision event timers that may be used by the operating
system. They are implemented as a single counter each with its own comparator
and value register.
IPMI
IPMI Controller NXP® ARM7 microcontroller with 512 kB firmware flash and automatic rollback
strategy
The IPMI controller carries out IPMI commands such as monitoring several
onboard temperature conditions, board voltages and the power supply status,
and managing hot swap operations.
The IPMI controller is accessible via two IPMBs, one host Keyboard Controller
Style (KCS) Interface and up to four Gigabit Ethernet Interfaces (IOL).
Table 1: CP6005(X)-SA Main Specifications (Continued)
FEATURES SPECIFICATIONS