Kramer 691 User manual

691 Quick Start (P/N: 2900-300523QS REV 2)
P/N:
2900- 300523QS
Rev:
2
Scan for full manual
691 Quick Start Guide
This guide helps you install and use your 691 for the first time.
Go to www.kramerav.com/downloads/691 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
691 HDBT 2.0 Optical Transmitter
4 Rubber feet
1 Power adapter (12V DC)
1 Quick start guide
Step 2: Get to know your 691
#
Feature
Function
1
USB Connector
Connect to the USB host for traffic extension, (for example, a laptop)
2
LINK LED
Lights green when the HDBT link is valid
3
IN LED
Lights green when an HDMI active signal device is connected
4
ON LED
Lights green when the device receives power
#
Feature
Function
5
HDMI IN Connector
Connect to the HDMI source
6
IR 3.5mm Mini Jack Connector
Connect to an external infrared transmitter or sensor for traffic extension
7
RS-232 3-pin Terminal Block
Connect to an RS-232 transmitter for traffic extension (for example, a PC to control the
projector)
8
AUDIO IN 3.5mm Mini Jack
Connect to the stereo, analog audio source for traffic extension
9
OUT IN SFP+ Connector
Connect the fiber optic cable to the OUT IN SFP+ LC connector
10
SETUP 4-way DIP-switch
Sets the device behavior
11
CONTROL
RS-232 3-pin
Terminal Block
Connect to the serial controller to control this device
12
ETHERNET RJ-45
Connector
Connect to the Ethernet controller to control this device or to a LAN to extend network traffic to
the receiver
13
RESET Switch
Press and hold while power-cycling the device to reset to factory default parameters
14
PROG Mini USB Connector
Connect to a PC to perform firmware upgrades
15
12V DC Power Connector
Connect to the supplied power adapter

Step 3: Install the 691
To mount the 691 in a rack, use an RK-1 rack adapter. Alternatively, attach the rubber feet to the underside of the 691 and place it
on a table.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your 691. For best results, we recommend that you always use Kramer high-
performance cables to connect AV equipment to the 691.
To install the OSP SFP+ transceiver:
1. Make sure the bail is pushed up, in the closed position.
2. Insert the OSP SFP+ transceiver into the relevant optical device SFP+
slot and push it in until it clicks.
Remove the protective cap and store it in a safe place for future use.
Warning: Connecting the OSP SFP+ connector to an LC(APC) fiber
connector may cause poor performance and damage the connector!
Refer to www.kramerav.com/downloads/OSP-MM1 for more information.
Warning: Class 1 Laser Product
Invisible laser radiation present.
Avoid long-term viewing of laser.
Avoid the use of magnifying viewing aids or instruments (such as binoculars, telescopes, microscopes and magnifying
lenses, but not spectacles or contact lenses).
Avoid placing optical devices in the emitted beam that could cause the concentration of the laser radiation to be
increased.

RJ-45 Pinout:
SETUP DIP-Switches
For the Ethernet connectors, see the proper
wiring diagram
A DIP-switch that is down is on, up is off. Changes to the DIP-switches only take
effect on power-up. After changing a switch, reboot the device.
PIN EIA /TIA 568B
PIN
Wire Color
#
Function
Status
1
Orange / White
1
For future use
2
Orange
2
Audio source priority
Off—Embedded audio (factory default)
On—Analog audio
3
Green / White
4
Blue
3
EDID lock
Off—Automatic EDID acquisition (factory default)
On—Lock (locks the current EDID so that changes
on the output do not result in changes to the EDID)
5
Blue / White
6
Green
7
Brown / White
4
Audio mode selection
Off—Auto (factory default)
On—Manual
8
Brown
Step 5: Connect the power
Connect the power adapter to the 691 and plug the adapter into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit
Warning:
Use only the Kramer Electronics power supply that is provided with the unit
Warning:
Disconnect the power and unplug the unit from the wall before installing
See www.KramerAV.com for updated safety information.
Step 6: Control the 691 via the:
Embedded Web pages:
RS-232 and Ethernet:
RS-232
Protocol 3000
Baud Rate:
115,200
Stop Bits:
1
Data Bits:
8
Parity:
None
Command format:
ASCII
Example (get device model name):
#model?<cr>
TCP/IP Parameters
IP Address:
192.168.1.39
UDP Port #:
50000
Subnet mask:
255.255.000.000
TCP Port #:
5000
Default gateway:
192.168.0.1
Full Factory Reset
Full Factory Reset
Rear panel button:
Press and hold to reset to factory default parameters
P3K command:
#factory<cr>
Embedded Web pages:
Select Device Settings page and click Factory reset
Default Parameters
Value
Name:
KRAMER_
Model:
691
Audio delay input switching on newsignal:
Immediate
Audio delay input switching on signal loss (leave 5V on):
5 seconds
Audio delay input switching on cable unplug:
Immediate
Video delay power off 5V on signal loss:
15 minutes
HDCP:
Follow output
Web Logon credentials:
Name: Admin; Password: Admin

Technical Specifications
Inputs:
1 HDMI on a female HDMI connector
1 Stereo analog unbalanced audio on a 3.5mm mini jack
Outputs:
1 Fiber Optic on an 10Gbps SFP+ LC connector complying with IEEE 802.3ae
Ports:
1 IR on a 3.5mm mini jack forIR link extension
1 USB on a female USB-B connector for USB link extension
1 Mini-USB connector for device Firmware upgrade
1 RS-232 on a 3-pin terminal block for serial link extension
1 RS-232 on a 3-pin terminal block for device control
1 10Base-T/100BaseTx Ethernet on an RJ-45 female connector for device control and
network traffic transfer
Fiber Extension Line:
HDBaseT 2.0 compliant
For optimum performance use the recommended multimode or singlemode Kramer SFP+
transceivers available at www.kramerav.com/product/691
Video:
Up to 10.2Gbps bandwidth (3.4Gbps per graphic channel); Up to 4K UHD @60Hz (4:2:0)
24bpp resolution; HDMI 2.0 and HDCP 1.4 signal compliance
Analog Audio:
Up to 1 Vrms level, 0.03% THD + NOISE @ 1kHz at nominal level
Extended USB:
1.1 and 2.0 Host compliance; Up to 127Mbps (out of max 480 USB) extended line rate
bandwidth; Up to 7 devices; Up to 2 hubs; Up to 8 ports per hub
Extended RS-232:
300 to 115200 baud rate
Control RS-232:
115200 baud rate
Cooling:
Convection ventilation
Operating Temperature:
0° to +40°C (32° to 104°F)
Storage Temperature:
-40° to +70°C (-40° to 158°F)
Humidity:
10% to 90%, RHL non-condensing
Power Consumption:
12V DC, 1300mA
Dimensions:
21.46cm x 16.3cm x4.36cm (8.45" x6.42" x 1.7") W, D, H
Shipping Dimensions:
35.1cm x 21.2cm x 7.2cm (13.82" x 8.35" x 2.8") W, D, H
Weight:
0.95 kg (2.1lbs)
Shipping weight:
1.45 kg (3.2lbs) approx.
Included Accessories:
Power supply (12V, 2A)
Options:
For optimum range and performance use the recommended USB, Ethernet, serial and IR
Kramer cables available at www.kramerav.com/product/691
Specifications are subject to change without notice at www.kramerav.com