Landoll Brillion 3631-25 User manual

®
LANDOLL COMPANY, LLC
1900 North Street
Marysville, Kansas 66508
[phone]
800-428-5655 ~WWW.LANDOLL.COM
‘
3631-25 Coil Tine Harrow Kit 213907
3631-30 Coil Tine Harrow Kit 213908
Instruction Sheet
F-984-0920

Manuals for Coil Tine Harrow Kit
Manual Number Manual Type
F-979 3631-25 Operator’s Manual
F-978 3631-25 Parts Manual
F-982 3631-30 Operator’s Manual
F-981 3631-30 Parts Manual
F-984 3631-25 / 3631-30 Coil Tine Harrow Kit, Instruction Sheet

F-984-0920 1-1
TABLE OF CONTENTS Chapter 1
Assembly
3631-25 Rear 3-Bar Coil Tine Harrow Kit
Kit Part Number 213907
Figure 1-1: 3631-25 Rear 3-Bar Coil Tine Harrow Kit
3630-25 RearHarrowOption
Harrow Arm Asm, Wing
Harrow Arm Asm, Wing
Harrow Asm, 4 Tine,3 Row
Harrow Asm, 5 Tine,3 Row
Harrow Asm, 6 Tine,3 Row
Harrow Asm, 4 Tine,3 Row
221593
213909
168800
168799 168798
221593
221594
Harrow Arm Assembly

1-2 F-984-0920
ASSEMBLY
TABLE OF CONTENTS
3631-30 Rear 3-Bar Coil Tine Harrow Kit
Kit Part Number 213908.
Figure 1-2: 3631-30 Rear 3-Bar Coil Tine Harrow Kit
3630-30NC RearHarrowOption
Wing Harrow Arm Assembly
Wing Harrow Arm Assembly
Harrow Asm 7 Tine 3 Row
Harrow Asm 6 Tine 3 Row Harrow Asm
5 Tine 3 Row
Harrow Arm
Assembly
Harrow Asm 5 Tine 3 Row
221593
221593
221594
198621
168801
168800 168799

ASSEMBLY
1-3
TABLE OF CONTENTS
CAUTION
WARNING
To ensure alignment of assemblies, leave the nuts loose
until completion of final assembly. Use lock washers or
flat washers as specified. Spread all cotter pins.
After completion of final assembly, tighten all nuts evenly
to prevent misalignment, distortion or binding. Tighten all
screws and nuts to recommended torques.
IMPORTANT
• If pre-assembled parts or fasteners are temporarily
removed, remember where they go. It is best to
keep parts separated.
• Check that all working parts move freely, bolts are
tightened and cotter pins spread.
• Refer to the operator’s manual Page 4-1 for proper
torque values. Note the different torque
requirements for bolts with locknuts.
“Left and “Right” refer to directions seen as if standing
behind the machine and facing in the direction of forward
travel.
Harrow Installation
NOTE
Wing Harrow Arms are different than Center Frame
Harrow Arms.
1. Unfold, lower the unit to the ground.
2. Refer to Figure 1-5 through 1-8 for the Harrow Arm
positioning.
3. Position Harrow Arm Assembly on the Center Frame
Rear Roller Tube or Wing Frame Rear Tube. Secure
with 3/4-10 U-Bolts and Locknuts. See Figure 1-3.
4. Attach the Harrow Assembly to the Harrow Arm
Assembly by placing the 3 x 3 tube into the Arm
Notch. Position 5/8-11 U-Bolt onto the 3 x 3 Tube and
through the Harrow Arm Assembly. Secure with Thick
Washers and Flange Nuts. See Figure 1-4.
a
Figure 1-3:Harrow Arm Installation to Frame
a
Figure 1-4: Harrow Arm Installation to Harrow
Assembly
Do not work on or under this machine unless
securely blocked and supported by a hoist or
tractor or by other sufficient means
Do not attempt to lift heavy parts manually. Use
a hoist or a fork lift to move these parts into
position.
Center and Wing Frame
Rear Frame Tube
Harrow Arm
Assembly
U-Bolt,3/4-10
Locknut,
3/4-10
Harrow
Assembly
3 x 3 Tube
Locknut,Flange
5/8-11
Thick Washer
U-Bolt,5/8-11
Harrow
Assembly
Harrow Arm
Assembly

1-4 F-984-0920
ASSEMBLY
TABLE OF CONTENTS
3631-25 Harrow Mounting Dimensions
Figure 1-5: 3631-25 Center Rear Harrow Mounting Dimensions
5 1/2"
27"
5 1/2"
27"
11 5/8"
11 1/4"
Harrow Assembly
168800
Harrow Assembly
168799
221594
Harrow Arm Assembly
without Lift

ASSEMBLY
1-5
TABLE OF CONTENTS
Figure 1-6: 3631-25 Wing Rear Harrow Mounting Dimensions
13 1/2"
17"
9 1/2"
Harrow Assembly
168798
RH Wing Frame
Rear Tube
13 1/2"
17"
9"
Harrow Assembly
213909
LH Wing Frame
Rear Tube
Harrow Arm Assembly
221593

1-6 F-984-0920
ASSEMBLY
TABLE OF CONTENTS
3631-30 Harrow Mounting Dimensions
Figure 1-7: 3631-30 Center Rear Harrow Mounting Dimensions
6"
38"
6"
38"
14 1/8"
13 3/4"
Harrow Assembly
168801
Harrow Assembly
168800
221594
Harrow Arm Assembly
without Lift

ASSEMBLY
1-7
TABLE OF CONTENTS
Figure 1-8: 3631-30 Wing Rear Harrow Mounting Dimensions
6 3/4"
34"
7 1/4"
Harrow Assembly
168799
RH Wing Frame
Rear Tube
6 3/4"
33 1/2"
6 3/4"
Harrow Assembly
198621
LH Wing Frame
Rear Tube
221593
Harrow Arm Assembly

1-8 F-984-0920
ASSEMBLY
TABLE OF CONTENTS
Table provided for general use.
NOTES: