Landoll Brillion 4630-36 Series User manual

®
LANDOLL COMPANY, LLC
1900 North Street
Marysville, Kansas 66508
[phone]
800-428-5655 ~WWW.LANDOLL.COM
‘
Model 4630-36
Folding Seeder
Operator’s Manual
F-640-0222

Manuals for 4630-36 Folding Seeder
Manual Number Manual Type
F-640 Operator’s Manual
F-641 Parts Manual

DANGER
Failure to comply with this warning may result
in serious injury or possibly death.
DO NOT operate or perform any maintenance tasks on this
equipment until you have completed the following:
1. Receive proper training to operate this equipment safely.
2. Read and understand the operator’s manual.
3. Be thoroughly trained on inspection and repair procedures.

i
Table of Contents
1 Safety Information
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Description of Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Owner Assistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Warranty Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Understanding Safety Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
High Power Magnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Transporting Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Safety Instructions for Towing Vehicles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Attaching, Detaching and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Protective Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Tire Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Chemical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Prepare for Emergencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
High Pressure Fluid Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Safety Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Decals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
2 Assembly
Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Seeder Unit 3-PT Hitch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Brillion Elite Mini Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Brillion Elite Mini Monitor - Single Seed Box Sensor Schematic . . . . . . . . . 2-4
Brillion Elite Mini Monitor - Double Seed Box Sensor Schematic . . . . . . . . . 2-5
Brillion Elite Mini Monitor - Ground Speed . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Brillion Elite Mini Monitor - Front Small Meter Seed Box Seed Shaft
Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Brillion Elite Mini Monitor - Front Large Meter Seed Box Seed Shaft
Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Brillion Elite Mini Monitor - Rear Brome Seed Box Seed Shaft Sensor . . . . 2-8
Brillion Elite Mini Monitor - Rear Small Meter Seed Box Seed Shaft
Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Brillion Elite Mini Monitor - Small Seed Box Front Box Bin Level Sensor. . . 2-9
Brillion Elite Mini Monitor - Mid Size Seed Box Bin Level Sensor. . . . . . . . . 2-9
Brillion Elite Mini Monitor - Large Seed Box Bin Level Sensor . . . . . . . . . . 2-10
Console w/Clutch - Seed Shaft Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Console w/Clutch - Seed Shaft Sensor Mounting Dimension. . . . . . . . . . . 2-11
Console w/Clutch - Single Box Sensor Schematic . . . . . . . . . . . . . . . . . . . 2-12
Console w/Clutch - Double Box Sensor Schematic . . . . . . . . . . . . . . . . . . 2-13
Center Seeder Unit Warning Lamp Installation. . . . . . . . . . . . . . . . . . . . . . . . 2-14

ii F-640-0222
TABLE OF CONTENTS
Attaching Seeder Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Center Harrow Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
Wing Harrow Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
Hydraulic Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Row Marker Installation – Optional. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Row Marker Kit 171633 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Row Marker Hydraulic Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Purge the Row Marker System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Scraper Kit Installation – Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
3 Operation
Tractor Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Folding Seeder Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Attaching Folding Seeder To Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Hydraulic Fold System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Hydraulic Seeder Unit Lift System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
General Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Operation of Transport Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Leveling the Folding Seeder and Seeder Units . . . . . . . . . . . . . . . . . . . . . . . 3-10
Brillion Elite Mini Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Seed Shaft Monitor with Clutch Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Coil Tine Harrows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Optional Row Markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Optional Row Marker Disc Blade Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Seeder Unit Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Transporting the Folding Seeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
4 Brillion Elite Mini Monitor
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Main Screen Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Speed & Icon Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Field & Total Acres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Settings Menu - Speed Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Speed Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Speed Source Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Speed Source Icon Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Pulses Per Revolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Wheel Pulses Per 400FT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Radar Pulses Per 400FT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Speed (Simulated Speed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Speed Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

iii
TABLE OF CONTENTS
Implement Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Implement Switch Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Settings Menu - Clutch Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Settings Menu - Install Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Learn New System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Remove A Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Add A Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Settings Menu - Shaft Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Seed Shaft Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Ground Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Settings Menu - Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Settings Menu - GPS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
GPS Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
GPS Baudrate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
GPS Speed Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Settings Menu - Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Brightness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Clock (Date & Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
System Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Update App. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Service And Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
5 Maintenance
General Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Hydraulic Fitting Torque Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Wheel Hub Bearing Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Lubrication Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Hydraulic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Hose Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Individual Seeder Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
LED Warning Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
6 General Reference and Specifications
Model Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

iv F-640-0222
TABLE OF CONTENTS

F-640-0222 1-1
TABLE OF CONTENTS Chapter 1
Safety Information
Introduction
The implement described in this manual has been
designed with care and built by skilled workers using
quality materials and processes. Proper assembly and
maintenance will provide you with satisfactory use for
seasons to come.
DANGER
DANGER
Description of Unit
The 4630-36 Folding Seeder folds forward for narrow
transport width and seeds 36 feet per pass with a variety
of Brillion Sure Stand or Landscape Seeders. Three 12
foot seeders make up this three-into-one design allowing
each seeder to operate completely independently of each
other. The individual frame-mounted three-point hitches
raise and lower the seeders without changing the position
of the mainframe allowing the operator to raise the
seeders at the end of the field effortlessly for turning. The
tractor mounted controller allows the operator to control
clutch engagement, view planted acreage, and monitor
seed shaft rotation along with minimum seed box levels.
Using this Manual
This manual will familiarize you with safety, assembly,
operation, adjustment, and maintenance. Read this
manual and follow the recommendations to help ensure
safe and efficient operation.
• The information in this manual is current at time of
printing. Some parts may have changed to assure top
performance.
• Location reference: Right and Left designations in this
manual are determined by facing the direction the
implement will travel during field operation, unless
otherwise stated.
Owner Assistance
If customer service or repairs are needed, contact your
Brillion dealer. They have trained personnel, parts and
service equipment specially designed for Brillion
products. Your implement’s parts should only be replaced
with Brillion parts. If items covered in this manual are not
understood, contact your local Brillion Dealer.
Warranty Registration
Brillion Farm Equipment, by Landoll, shall have no
warranty obligation unless each product is registered
within 10 days of retail purchase, using the Landoll
Company, LLC Ag Products on-line registration process.
Please refer to the Ag Products Policy and Procedures
Manual, accessible at www.landoll.com for step by step
instructions regarding product registration.
Enter your product information below for quick reference.
MODEL NUMBER
SERIAL NUMBER
DATE OF PURCHASE
Refer to the ID plate as shown. See Figure 1-1..
a
Figure 1-1: ID Plate
Read this entire manual before attempting to
assemble, adjust or operate this implement.
Failure to comply with this warning can result in
personal injury or death, damage to the implement
or its components and inferior operation.
MODEL #
SERIAL #
MADE IN USA 1-573-010006
Landoll Company, LLC
Marysville, Kansas
www.landoll.com

1-2 F-640-0222
TABLE OF CONTENTS
Safety
NOTE
Investigation has shown that nearly 1/3 of all farm
accidents are caused by careless use of machinery. Insist
that all people working with you or for you abide by all
safety instructions.
Understanding Safety Statements
You will find various types of safety information on the
following pages and on the implement decals (signs)
attached to the implement. This section explains their
meaning.
NOTICE
CAUTION
WARNING
DANGER
DANGER
NOTE
You should read and understand the information
contained in this manual and on this implement decals
before you attempt to operate or maintain this equipment.
• Examine safety decals and be sure you have the
correct safety decals for the implement. See
Figure 1-3..
• Order replacement decals through your Brillion dealer.
• Keep these signs clean so they can be observed
readily. It is important to keep these decals cleaned
more frequently than the implement. Wash with soap
and water or a cleaning solution as required.
• Replace decals that become damaged or lost. Also, be
sure that any new implement components installed
during repair include decals which are assigned to
them by the manufacturer.
• When applying decals to the implement, be sure to
clean the surface to remove any dirt or residue. Where
possible, sign placement should protect the sign from
abrasion, damage, or obstruction from mud, dirt, oil etc.
DANGER
DANGER
High Power Magnet
The Brillion Elite Mini Monitor uses very powerful
Neodymiun Mangets. Read all the warnings before
operating the machine.
WARNING
Special notice - read and thoroughly understand.
Proceed with caution. Failure to heed caution may
cause injury to person or damage product.
Proceed with caution. Failure to heed warning will
cause injury to person or damage product.
Proceed with extreme caution. Failure to heed
notice will cause injury or death to person and/or
damage product.
• Do not allow anyone to ride on the tractor or
implement. Riders could be struck by foreign
objects or thrown from the implement.
• Never allow children to operate equipment.
• Keep bystanders away from implement during
operation.
1. Neodymiun Magnets are brittle; they can be
broken or can splinter in a collision. One
should wear gloves and protective glasses
when handling these magnets, because
splinters and/or spacers could disengage and
fly from the magnets.
2. Normal Neodymium Magnets will lose their
magnetic properties if heated above 175°F
(80° C).
3. The strong magnetic fields of Neodymium
Magnets can damage items such as
televisions, computer monitors, credit cards,
bank cards, computers, diskettes and other
data carriers, video tapes, mechanical
watches, hearing aides, loud speakers and
VCRs. Pace-Makers may be damaged or
switch to "Test Mode" in the presence of a
strong magnetic force, if a Pace-Maker or
other electrical body implant is in use, Keep a
Minimum of 3 Feet Distance.
4. Children should not be allowed to handle
Neodymium Magnets as they can be
dangerous. Small magnets pose a choking
hazard and should never be swallowed or
inserted into any part of the body.
5. Under no circumstances should you try to cut,
saw or drill the Neodymium Magnet! Not only
would the magnet break, but the resulting dust
from the magnet is very flammable.
Neodymium Magnets should never be burned,
as burning them will create toxic fumes.

F-640-0222 1-3
TABLE OF CONTENTS
Transporting Safety
IMPORTANT
It is the responsibility of the owner/operator to
comply with all state and local laws.
• When transporting the implement on a road or highway,
use adequate warning symbols, reflectors, lights and
slow moving vehicle sign as required. Slow moving
tractors and towed implements can create a hazard
when driven on public roads. They are difficult to see,
especially at night.
• Do not tow an implement that, when fully loaded,
weighs more than 1.5 times the weight of the towing
vehicle.
• Carry reflectors or flags to mark the tractor and
implement in case of breakdown on the road.
• Do not transport at speeds over 20 MPH under good
conditions. Never travel at a speed which does not
allow adequate control of steering and stopping.
Reduce speed if towed load is not equipped with
brakes.
• Avoid sudden stops or turns because the weight of the
implement may cause the operator to lose control of
the tractor. Use a tractor heavier than the implement.
• Use caution when towing behind articulated steering
tractors; fast or sharp turns may cause the implement
to shift sideways.
• Keep clear of overhead power lines and other
obstructions when transporting. Know the transport
height and width of your implement. See Figures 5-1
and 5-2.
Safety Instructions for Towing
Vehicles
The maximum travel speed is the lesser of
• The limit of the road conditions;
• The maximum specified ground speed;
— for towing operations as indicated in this manual
or SIS;
— of the towed vehicle as indicated in its operator’s
manual, SIS, or information sign;
• The maximum ground speed of the towed equipment
combination shall be limited to the lowest specified
ground speed of any of the towed machines. This
speed is the ground speed limitation.
EXAMPLE: If the tractor is capable of 25 mph, the first
implement has a SIS for 19 mph, and the last
implement’s operator’s manual states its specified
ground speed is 15 mph, the towed equipment
combination ground speed limitation is 15 mph.
Attaching, Detaching and Storage
• Do not stand between the tractor and implement when
attaching or detaching implement unless both are
blocked from moving.
• Before applying pressure to the hydraulic system, be
sure all connections are tight and that hydraulic hoses
are not damaged.
• Block implement so it will not roll when unhitched from
the tractor.
• Relieve pressure in hydraulic circuit before uncoupling
hydraulic hoses from tractor.
NOTE
To relieve hydraulic pressure: Depending on tractor
hydraulic system, some can be relieved by actuating
control lever after engine is stopped. If tractor has electric
over hydraulic controls, it may be necessary to move the
control lever to the float position. Refer to tractor’s
operator’s manual.
Wear protective gloves and safety glasses or goggles
when working with hydraulic systems.
Maintenance Safety
• Block the implement so it will not roll when working on
or under it to prevent injury.
• Do not make adjustments or lubricate the machine
while it is in motion.
• Make sure all moving parts have stopped.
• Understand the procedure before doing the work. Use
proper tools and equipment.
Protective Equipment
• Wear protective clothing & equipment appropriate for
the job. Avoid loose fitting clothing.
• Because prolonged exposure to loud noise can cause
hearing impairment or hearing loss, wear suitable
hearing protection, such as earmuffs or earplugs.
Tire Safety
Tire changing can be dangerous and should be performed
by trained personnel using correct tools and equipment.
• When inflating tires, use a clip-on chuck and extension
hose long enough to allow you to stand to one side, not
in front of or over the tire assembly. Use a safety cage
if available.
• When removing and installing wheels use
wheel-handling equipment adequate for the weight
involved.

1-4 F-640-0222
TABLE OF CONTENTS
Chemical Safety
Agricultural chemicals can be dangerous. Improper use
can seriously injure persons, animals, plants, soil &
property.
• Read chemical manufactures instructions and store or
dispose of unused chemicals as specified. Handle
chemicals with care & avoid inhaling smoke from any
type of chemical fire.
• Store or dispose of unused chemicals as specified by
the chemical manufacturer.
Prepare for Emergencies
• Keep a First Aid Kit and Fire Extinguisher handy.
• Keep emergency numbers for the doctor, ambulance,
hospital and fire department near the phone.
High Pressure Fluid Safety
Escaping fluid under pressure can be nearly invisible and
have enough force to penetrate the skin causing serious
injury. Use a piece of cardboard, rather than hands, to
search for suspected leaks.
Any fluid injected into the skin must be surgically removed
within a few hours or gangrene may result.
Avoid the hazard by relieving pressure before
disconnecting hydraulic lines.
NOTE
Relieve hydraulic pressure by shifting the control valve
lever to float.
Wear protective gloves and safety glasses or goggles
when working with hydraulic systems.
Safety Chain
Use the safety chain to help control drawn machinery
should it separate from the tractor drawbar.
• Use a chain with a strength rating equal to or greater
than the gross weight of towed machinery, which is
21,100 pounds minimum in accordance with ASAE
S338.2 specifications. If two or more implements are
pulled in tandem, a larger chain may be required.
Chain capacity must be greater than the TOTAL
weight of all towed implements.
• A second chain should be used between each
implement.
• Attach the chain to the tractor drawbar support or
specified anchor location. Allow only enough slack in
the chain to permit turning. The distance from hitch pin
to attachment point or intermediate support point
should not exceed 9 inches. See Figure 1-2.
• Replace the chain if any links or end fittings are
broken, stretched or damaged.
• Do not use a safety chain for towing.
Figure 1-2: Safety Chain
9" Max
Flat Washer,1"
Locknut,1-8
Safety Chain
Tractor Drawbar
Hitch
Telescoping
Hitch Tube
Seeder Hitch
Frame

F-640-0222 1-5
TABLE OF CONTENTS
Decals
Figure 1-3: Decals
ITEM 1
1-573-010006
MODEL #
SERIAL #
MADE IN USA 1-573-010006
Landoll Company, LLC
Marysville, Kansas
www.landoll.com
20
mile/h
144193
ITEM 3
144193
ITEM 5
2-573-010198
FARM EQUIPMENT
MANUFACTURERS
ASSOCIATION
MEMBER
ITEM 6
2-573-010330-03
DANGER
To prevent serious injury or death
from pinching:
Keep all persons and objects clear
while any part of this machine is in
motion.
2-573-010335
ITEM 7
2-573-010335
A LANDOLL PRODUCT
ITEM 8
170509
A LANDOLL PRODUCT
ITEM 9
170510
WARNING
8-573-010084
1. BEFORE OPERATING - STUDY OPERATORS MANUAL SAFETY
MESSAGES AND SAFE OPERATING PROCEDURES. READ SAFETY
SIGNS ON THIS MACHINE.
2. TRANSPORT ON PUBLIC ROADS - OBSERVE FEDERAL, STATE,
AND LOCAL REGULATIONS; DISPLAY SMV EMBLEM; ATTACH
PROPER STRENGTH IMPLEMENT SAFETY CHIAN; AND LIMIT
MAXIMUM SPEED TO 20mpg (32km/h)
3. LOWER OR BLOCK ALL ELEVATED COMPONENTS BEFORE SER-
VICING OR LEAVING THIS MACHINE.
ITEM 10
8-573-010084
ITEM 11
171606
P/N: 1410224 REV-A
ITEM 12
1410224
ITEM 2
141597
ITEM 17
528938
ITEM 15
528934
ITEM 16
528933
HOSE IDENTIFICATION
155523
BLUE - LIFT WHEELS
YELLOW - WING FOLD
BLACK - AUXILIARY
ITEM 4
155523
ITEM 4
219155
HOSE IDENTIFICATION
BLUE - LIFT WHEELS
YELLOW - WING FOLD
BLACK - SECTION LIFTS
RED - MARKERS 219155
CAUTION
MOVING MACHINES CAN CAUSE INJURY. KEEP AWAY!
1. KEEP AWAY FROM MOVING TRACTORS OR IMPLEMENTS.
KEEP OTHERS AWAY.
2. DO NOT RIDE OR ALLOW OTHERS TO RIDE ON TRACTOR
OR IMPLEMENT.
3. BLOCK IMPLEMENT TO PREVENT MOVEMENT WHEN
UNHITCHED FROM TRACTOR.
4. KEEP ALL GUARDS AND SHIELDS IN PLACE WHILE
MACHINE OR PARTS ARE IN MOTION. 8J309
ITEM 18
8J309
AG SEEDER
P/N: 235621
ITEM 14
235621
FOLDING
SEEDER
P/N: 234507
ITEM 13
234507
FOLDING
SEEDER
P/N: 234507
ITEM 13
234507
LANDSCAPE
SEEDER
P/N: 235624
ITEM 14
235624

1-6 F-640-0222
TABLE OF CONTENTS
Figure 1-4: Decal Placement (1 of 2)
2
12
3
13
4
5
1
6
7
8
19
9
10
9
6
8
9
12

F-640-0222 1-7
TABLE OF CONTENTS
Figure 1-5: Decal Placement (2 of 2)
REAR VIEW
FRONT VIEW
RH SIDE VIEW LH SIDE VIEW
15
8
8
15
15 15
15
18
18
88
8
815
15
15
11 11
16 17 16 17
11
141,1918 141,19141,19

1-8 F-640-0222
TABLE OF CONTENTS
Table provided for general use.
NOTES:

F-640-0222 2-1
TABLE OF CONTENTS Chapter 2
Assembly
CAUTION
WARNING
CAUTION
NOTE
Refer to the repair Parts Manual F-641 for identification of
parts and for the approximate relationship of the parts in
assembly.
To ensure alignment of assemblies, leave the nuts loose
until completion of final assembly. Use lock washers or
flat washers as specified. Spread all cotter pins.
After completion of final assembly, tighten all nuts evenly
to prevent misalignment, distortion or binding. Tighten all
screws and nuts to the recommended torques.
IMPORTANT
• If pre-assembled parts or fasteners are temporarily
removed, remember where they go. It is best to keep
parts separated.
• Check that all working parts move freely, bolts are tight
and cotter pins spread.
• Refer to the Torque Table for proper torque valves.
Note the different torque requirements for Bolts with
Locknuts. See Page 5-1.
“Left” and “Right” refer to directions seen as if standing
behind the machine and facing in the direction of forward
travel.
The 4630-36 Folding Seeder comes assembled.
Depending on the seeder model chosen, the three
assembled seeder units and seeder attachments need to
be assembled onto the Folding Seeder Hitch.
• Prepare tractor for operation. See “Tractor
Preparation” on page 3-2.
• Prepare Folding Seeder. See “Folding Seeder
Preparation” on page 3-2.
• Attach Folding Seeder to tractor. “Attaching Folding
Seeder To Tractor” on page 3-2
Do not work on or under this machine unless
securely blocked and supported by a hoist or
tractor or by other sufficient means.
Do not attempt to lift heavy parts (such as the
Frame, Rockshaft, and Pull Hitch) manually. Use a
hoist or a fork lift to move these parts into
position.
Secure the Seeder Hitch to a tractor and unfold
the wings of the hitch when attaching seeder
unit(s). This will provide stability and ease
attachment of the seeder unit(s).

2-2 F-640-0222
TABLE OF CONTENTS
Hydraulic System
NOTE
It is good practice to purge the Hydraulic System before
installing the Seeder Units onto the Folding Seeder Hitch
to ensure that the circuits are functioning properly.
4630-36 hydraulic system consists of 3 separate circuits
with an Optional Row Marker Circuit.
Lift Circuit – Blue
• Folding Seeder raised requires approximately
3.2 gallons hydraulic oil
• Folding Seeder lowered requires approximately
2.7 gallons hydraulic oil
Fold/Unfold Circuit – Yellow
• Folding Seeder Folded requires approximately
2.8 gallon hydraulic oil
• Folding Seeder Unfolded requires approximately
3.2 gallons hydraulic oil
Seeder Unit Lifts Circuit – Black
• Seeder Units raised requires approximately
1.9 gallons hydraulic oil
• Seeder Units lowered requires approximately
2.1 gallons hydraulic oil
Optional Row Marker Circuit – Red
• Row Markers raised requires approximately
1.7 gallons hydraulic oil
• Row Markers lowered requires approximately
1.6 gallons hydraulic oil
Tightening Procedure for JIC 37 degree Swivel
Female Nuts.
1. Check Fitting Flare and seat for defects.
2. Lubricate the connection.
3. Install Hydraulic Hoses without twists.
4. Hand Tighten until connections bottoms.
5. Using 2 wrenches to prevent twisting, rotate the
Swivel Nut 2 wrench flats (1/3 turn).
6. For reassembly, follow the same procedure but
tighten only 1 wrench flat (1/16 turn).
Tightening Procedure for Swivel O-Ring Fittings.
1. Lubricate O-Ring and install the Fitting until the Metal
Washer which backs up the O-Ring contacts the face
of the boss.
2. Orient the Fitting by turning counterclockwise up to 1
turn.
3. Tighten the Locknut using 50-60 Ft-Lbs of torque. See
“Hydraulic Fitting Torque Specifications” on
page 5-2
Seeder Unit 3-PT Hitch
Installation
1. Support the Seeder Unit with a hoist or by similar
means capable of supporting its weight without
tipping.
2. Center a Seeder 3-PT Hitch Assembly in relationship
with the each Seeder Units Center Seed Box Support
Bracket. Attach the 3-PT Hitch Assembly to each
Seeder Frame Tube with 5/8-11 U-Bolts, Lock
Washers and Nuts. See Figure 2-1.
Figure 2-1: 3-PT Seeder Hitch Installation
Brillion Elite Mini Installation
IMPORTANT
The Brillion Elite Mini Monitor System by Loup
utilizes a MUX communication line. Sensors must be
learned into the Monitor. Location of each pre-learned
Smart Shaft Sensor or Bin Level Sensor is important
for proper Monitor display. Each Sensor utilizes 3
wires (+, -, MuxBus) to connect to the system. The
Harnesses do not require a specific Sensor
connection points. Each Sensor is identified in the
Monitor by its own signal.
Refer to Brillion Elite Mini Monitor Single or Double Box
Sensor Schematic. See Figures 2-3 and 2-4.
WARNING
High Power Magnet in use. See “High Power
Magnet” on page 1-2.
3-PT Hitch
Nut,5/8-11
Lock
Washer,5/8
U-Bolt,
5/8-11
Seeder
Frame Tube
Center
Support Bracket

F-640-0222 2-3
TABLE OF CONTENTS
IMPORTANT
All Harnesses must be firmly attached to Machine
Frame members so they do not sag or become torn
loose by field debris.
Folding Seeder Hitch
1. Orient the Main Harness so that the single 6-Pin
connector is to the front and the three 6-Pin
connectors are to the rear of the Seeder Hitch. Route
the Main Harness inside the Seeder Hitch Tube.
2. Install Brillion Elite Mini Monitor on tractor.
3. If not already installed, install Smart Clutch Relay into
Elite Mini Tractor Harness 3-Pin Connectors.
4. Connect the Elite Mini Tractor Harness 14-Pin
Connector to Brillion Elite Mini Monitor, 3-Pin Power
Plug to the 12 Volt Tractor Convenience Outlet and
6-Pin Connector to the Main Harness. 4-Pin
Connector is not used at this time.
Seeder Units
1. Lay out the Seeder Harnesses on the front of each
Seeder section ensuring that the Electric Clutch 2-Pin
Connector is on the left side.
2. On the Center Seeder only, remove Clutch. Install
Actuator Assembly onto the Quill Shaft outer
diameter, secure with Actuator Assembly Set Screw.
Reinstall Clutch. See Figure 2-5. Install Pick-up
Switch Bracket to the Transmission Input Shaft
Bearing Flangette Hardware. Assemble Smart Shaft
Sensor onto the Pick-Up Switch Bracket with sensor
provided hardware and #8-32 Flange Locknuts.
Adjust the Smart Shaft Sensor so that it is 1/8" Max
away from the Actuator Assembly. See Figure 2-6.
Connect Ground Speed Smart Shaft Sensor to the
Center Seeder Harness.
3. RH and LH Seeders do not have a Ground Speed
Smart Shaft Sensor, seal each Seeder Harness
Connector with a 3-Pin Shroud and Cavity Plugs to
protect the Seeder Harness from the environment.
4. On the RH side of each Seeder Unit a Sensor Mount
is mounted on two seed Cups. Install a Smart Shaft
Sensor to the Sensor Mount with sensor provided
hardware and #8-32 Flange Locknuts. Adjust the
Smart Shaft Sensor so that it is 1/8" Max away from
the pre-assembled Magnet Collar/Magnet Wheel
Assembly on the Seed Shaft. See Figures 2-7 and
2-8. Connect the Smart Seed Shaft Sensor to each
Seeder Harness.
5. If equipped with Rear Brome Seed Box, verify that the
pre-assembled Smart Shaft Sensor is positioned 1/8"
Max away from the Magnet Mount Assembly and
connect the Smart Shaft Sensor to each Seeder
Harness. See Figure 2-9. If not equipped with a Rear
Brome Seed Box, seal the Seeder Harness
Connector with 3-Pin Shroud and Cavity Plugs to
protect the Seeder Harness from the environment.
6. If Large Capacity Landscape Seeder is equipped with
a Rear Seed Box verify that the pre-assembled Smart
Shaft Sensor is positioned 1/8" Max away from the
Magnet Mount Assembly and connect the Smart
Shaft Sensor to each Seeder Harness. See
Figure 2-10. If not equipped with a Rear Seed Box,
seal the Seeder Harness Connector with 3-Pin
Shroud and Cavity Plugs to protect the Seeder
Harness from the environment.
7. Each Seeder Section has a Bin Level Sensor Bracket
on the inside at either end. Determine the desired
level for the alarm to be indicated on the Brillion Elite
Mini Monitor and assemble the Bin Level Sensors to
Bin Level Sensor Brackets with sensor provided
hardware and #8-32 Flange Locknuts. See
Figures 2-11, 2-12, and 2-13. If more adjustment is
needed, the Bin Level Sensor Brackets can also be
raised or lowered to the desired seed level. To get the
Sensor Connector outside the Seed Box, feed the
terminals through the Cord Grip. Install the terminals
into the 3-Pin Shroud labeled “A”, “B” and “C” as
follows “A” White, “B” Black, “C” Green. See
Figure 2-2. Inside the Seed Box, add enough slack to
the Bin Level Sensor Cord to allow for future
adjustment of the sensor. Secure Bin Level Sensor
Cord by tightening the Cord Grip Compression Nut.
Connect both Bin Level Sensors to each Seeder
Harness.
Figure 2-2: Bin Level Sensor Bracket Wire Detail
8. Attach Seeder Units to Folding Seeder Hitch. See
“Attaching Seeder Units” on page 2-16.
9. Connect 72" Extension Harness to the Center Seeder
and Main Harness.
10. Connect a 240" Extensions Harness to the RH and LH
Seeder Harnesses and connect both 240" Extension
Harnesses to the Main Harness.
11. Bundle and secure all Harnesses along the Seeder
Unit Frames and Folding Seeder Hitch Frame with Tie
Wraps
12. Program Bin Level Sensors and Smart Shaft Sensors
if not already pre-programmed.
White Wire
Black Wire
Green Wire
Terminal
3 Pin Shroud
Shroud Pin ID
Seal

2-4 F-640-0222
TABLE OF CONTENTS
Brillion Elite Mini Monitor - Single Seed Box Sensor Schematic
Figure 2-3: Brillion Elite Mini Monitor - Single Seed Box Sensor Schematic
Brillion Elite Mini Monitor
Smart Clutch
Relay
Elite Mini Tractor
Harness
240" Extension
Harness
Seeder
Harness
72" Extension
Harness
Bin Level
Sensor #4
Bin Level
Sensor #6
Smart Shaft
Sensor #3
Seeder
Harness
Bin Level
Sensor #5
Cavity Plug
Smart Shaft Sensor
Ground Speed
Cavity Plug
3-Pin Shroud
3-Pin
Shroud
Cavity Plug
3-Pin Shroud
Cavity
Plug
Monitor Mount
Smart Shaft
Sensor #2
Cavity
Plug
3-Pin
Shroud
Bin Level
Sensor #3
Bin Level
Sensor #2
Smart Shaft
Sensor #1
Seeder
Harness
Bin Level
Sensor #1
Clutch #2 included
with Seeder
Clutch #1 included
with Seeder
Clutch #3 included
with Seeder
240" Extension
Harness
Main
Harness
3-Pin
Power Plug
4 Pin Radar/GPS Plug
LH Seeder RH Seeder
Center Seeder
6-Pin
Connection