Landoll Weatherproofer III 2310 Series User manual

F-556-0910 09/2010
LANDOLL CORPORATION
1900 North Street
Marysville, Kansas 66508
[phone]
800-428-5655 ~ WWW.LANDOLL.COM
Model 2310
Weatherproofer III
Operator’s Manual

F-556-0910 Edition i
Table of Contents
1 Introduction
Understanding Safety Statements ................................................ 1-2
2 Standard Specifications
3 Assembly Instructions
Weatherproofer III Frame Assembly ............................................... 3-3
2310-7-30 & 8-30 Wing Extension Assembly ........................................ 3-5
Wheel Lift Installation .......................................................... 3-7
Hitch Installation .............................................................. 3-9
Depth Stop Tube Assembly .................................................... 3-11
Disc Gang and Depth Adjustment Installation ..................................... 3-13
Auto Reset Shank and Shovel Installation ........................................ 3-16
Disc Gang Depth Gauge Assembly .............................................. 3-19
Hydraulic Installation .......................................................... 3-26
Light Installation ............................................................. 3-28
Final Assembly ............................................................... 3-29
Rear Jack Installation ......................................................... 3-30
Rear Jack Installation (2310-07-30) (Option) ....................................... 3-31
Chopper Reel Installation (Option) ............................................... 3-32
4 Operation and Maintenance
Tractor Preparation ............................................................ 4-2
Weatherproofer Preparation ..................................................... 4-2
Attaching to the Tractor ........................................................ 4-2
Hydraulic Lift System .......................................................... 4-3
Hydraulic Fold System ......................................................... 4-4
Hydraulic Disc Gang Lift System ................................................. 4-6
General Operation ............................................................. 4-6
Field Operation ................................................................ 4-7
Leveling (Front-to-Rear) ........................................................ 4-7
Variable Ratio Adjustment ...................................................... 4-8

ii F-556-0910 Edition
Disc Blades ...................................................................4-9
Disc Gang Angle Settings ......................................................4-11
Depth Stop Adjustment (Manual) ................................................4-13
Wheel Bearing Maintenance ....................................................4-13
Hydraulic Maintenance ........................................................4-14
Transport ....................................................................4-14
Lubrication Maintenance .......................................................4-17
Storage .....................................................................4-17
5 Troubleshooting Guide

1-1
Chapter 1
Introduction
The Landoll Model 2310 Weatherproofer III is a quality product designed to give years of trouble free performance. By
following each section of this manual, your system will perform as designed for you and your operation
CHAPTER 1 gives basic instructions on the use of this manual.
CHAPTER 2 gives product specifications. These specifications supply lengths and measures for your
equipment. A Standard Bolt Torque Table is provided to give guidelines for bolt torques to
be used when servicing this product.
CHAPTER 3 contains assembly instructions for your Model 2310 Weatherproofer III. When these
procedures are correctly followed, your equipment should provide you years of
trouble-free operation and service.
CHAPTER 4 instructs how to operate your equipment before using it, and describes adjustments
needed. It also gives practical advice for the care and maintenance of your Landoll
equipment. Drawings in this section locate adjustment points on the equipment.
NOTE: IF THE EQUIPMENT IS IMPROPERLY ASSEMBLED OR MAINTAINED, THE
WARRANTY IS VOID. IF YOU HAVE ANY QUESTIONS CONTACT:
LANDOLL CORPORATION
1900 NORTH STREET
MARYSVILLE, KANSAS 66508
or phone:
[phone] or
[phone]
or FAX:
[phone]
CHAPTER 5 is a troubleshooting guide to aid in diagnosing and solving problems with the equipment.
PARTS LIST is a separate manual showing the various assemblies, subassemblies, and systems.
Refer to that manual when ordering Landoll replacement parts. Order parts from your
Landoll dealer.
WARRANTY The Warranty Registration form is included with the product documents. Fill it out and
mail it within 15 days of purchase.
NOTE: IMPROPER ASSEMBLY, MODIFICATION, OR MAINTENANCE OF YOUR
LANDOLL MACHINE CAN VOID YOUR WARRANTY.
COMMENTS Address comments or questions regarding this publication to:
LANDOLL CORPORATION
1900 NORTH STREET
MARYSVILLE, KANSAS 66508
ATTENTION: PUBLICATIONS -DEPT. 55

1-2 F-556-0910 Edition
INTRODUCTION
Understanding Safety
Statements
You will find various types of safety information on the
following pages and on the machine signs (decals)
attached to the vehicle. This section explains their
meaning.
The Safety Alert Symbol means ATTENTION! YOUR
SAFETY IS INVOLVED!
DANGER
WARNING
CAUTION
NOTE
Means that failure to follow these instructions could
cause damage to the equipment or cause it to operate
improperly.
NOTE
Make sure you read and understand the information
contained in this manual and on the machine signs
(decals) before you attempt to operate or maintain this
vehicle.
The safety statements contained in this manual relate to
the operation of the Model 2310 Weatherproofer III.
Danger means a life-threatening situation exists.
Death can occur if safety measures or
instructions on this label are not properly
followed.
Warning means serious injury or death can occur
if safety measures or instructions on this label
are not properly followed.
Caution means serious equipment or other
property damage can occur if instructions on this
label are not properly followed.

2-1
Chapter 2
Standard Specifications
2310 SERIES WEATHERPROOFER III
MODEL
NO.
NO. OF
BLADES
NO. OF
SHANKS
SHANK
SPACING
WORKING
WIDTH
TRANSPORT
WIDTH
ESTIMATED
WEIGHT (LBS.)
2310-4-30 14/16 4 30” 11’-7” 13’-7” 11,795
2310-5-24 14/16 5 24” 11’-7” 13’-7” 12,140
2310-5-30 16/18 5 30” 14’-9” 15’-4” 13,610
2310-6-24 16/18 6 24” 14’-9” 15’-4” 13,955
2310-6-30 18/20 6 30” 16’-5” 17’-1” 15,350
2310-7-24 18/20 7 24” 16’-9” 17’-1” 15,695
2310-7-30 22/24 7 30” 19’-11” 17’-9” 18,780
2310-8-30 24/26 8 30” 21’-7” 18’-11” 19,900

2-2 F-556-0910 Edition
STANDARD SPECIFICATIONS
Table 2-1: General Torque Specifications
LANDOLL CORPORATION
GENERAL TORQUE SPECIFICATIONS (REV. 4/97)
THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS
OR DRAWING.
ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION). THEY
DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.
WHEN FASTENERS ARE DRY (SOLVENT CLEANED), ADD 33% TO AS RECEIVED CONDITION TORQUE.
BOLT HEAD IDENTIFICATION MARKS INDICATE GRADE AND MAY VARY FROM MANUFACTURER TO MANUFACTURER.
THICK NUTS MUST BE USED ON GRADE 8 CAPSCREWS.
USE VALUE IN [ ] IF USING PREVAILING TORQUE NUTS.
TORQUE IS SPECIFIED IN FOOT POUNDS
UNC
Size
SAE Grade
2
SAE Grade
5
SAE Grade
8
UNF
Size
SAE Grade
2
SAE Grade
5
SAE Grade
8
1/4-20 4 [5] 6 [7] 9 [11] 1/4-28 5 [6] 7 [9] 10 [12]
5/16-18 8 [10] 13 [16] 18 [22] 5/16-24 9 [11] 14 [17] 20 [25]
3/8-16 15 [19] 23 [29] 35 [43] 3/8-24 17 [21] 25 [31] 35 [44]
7/16-14 24 [30] 35 [43] 55 [62] 7/16-20 27 [34] 40 [50] 60 [75]
1/2-13 35 [43] 55 [62] 80 [100] 1/2-20 40 [50] 65 [81] 90 [112]
9/16-12 55 [62] 80 [100] 110 [137] 9/16-18 60 [75] 90 [112] 130 [162]
5/8-11 75 [94] 110 [137] 170 [212] 5/8-18 85 [106] 130 [162] 180 [225]
3/4-10 130 [162] 200 [250] 280 [350] 3/4-16 150 [188] 220 [275] 320 [400]
7/8-9 125 [156] 320 [400] 460 [575] 7/8-14 140 [175] 360 [450] 500 [625]
1-8 190 [237] 408 [506] 680 [850] 1-14 210 [263] 540 [675] 760 [950]
1-1/8-7 270 [337] 600 [750] 960 [1200] 1-1/8-12 300 [375] 660 [825] 1080 [1350]
1-1/4-7 380 [475] 840 [1050] 1426 [1782] 1-1/4-12 420 [525] 920 [1150] 1500 [1875]
1-3/8-6 490 [612] 110 [1375] 1780 [2225] 1-3/8-12 560 [700] 1260 [1575] 2010 [2512]
1-1/2-6 650 [812] 1460 [1825] 2360 [2950] 1-1/2-12 730 [912] 1640 [2050] 2660 [3325]
1-3/4-5 736 [920] 1651 [2063] 2678 [3347] 1-3/4-12 920 [1150] 2063 [2579] 3347 [4183]
METRIC
COARSE THREAD METRIC CLASS 10.9 FASTENERS AND CLASS 10.0 NUTS AND THROUGH HARDENED FLAT WASHERS, PHOSPHATE COATED, ROCKWELL
“C” 38-45.
USE VALUE IN [ ] IF USING PREVAILING TORQUE NUTS.
Nominal
Thread
Diameter
mm
Standard Torque Nominal
Thread
Diameter
mm
Standard Torque
Newton-
Meters
Foot-
Pounds
Newton-
Meters
Foot-
Pounds
6 10 [14] 7 [10] 20 385 [450] 290 [335]
7 16 [22] 12 [16] 24 670 [775] 500 [625]
8 23 [32] 17 [24] 27 980 [1105] 730 [825]
10 46 [60] 34 [47] 30 1330 [1470] 990 [1090]
12 80 [101] 60 [75] 33 1790 [1950] 1340 [1450]
14 125 [155] 90 [115] 36 2325 [2515] 1730 [1870]
16 200 [240] 150 [180] 39 3010 [3210] 2240 [2380]
18 275 [330] 205 [245]

STANDARD SPECIFICATIONS
2-3
Table 2-2: Hydraulic Fitting Torque Specifications
LANDOLL CORPORATION
HYDRAULIC FITTING TORQUE SPECIFICATIONS
37oJIC, ORS, & ORB (REV. 10/97)
THIS CHART PROVIDES TIGHTENING TORQUES FOR HYDRAULIC FITTING APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS
OR DRAWING.
ASSEMBLY TORQUES APPLY TO PLATED CARBON STEEL AND STAINLESS STEEL FITTINGS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS
RECEIVED CONDITION).THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.
BRASS FITTINGS AND ADAPTERS - 65% OF THE TORQUE VALUE FOR STEEL. STAINLESS STEEL, ALUMINUM AND MONEL - THREADS ARE TO BE
LUBRICATED.
TORQUE IS SPECIFIED IN FOOT POUNDS
PARKER BRAND FITTINGS
Dash Size 37 Degree JIC O-Ring (ORS) O-Ring Boss (ORB)
-4 11-13 15-17 13-15
-5 14-16 — 21-23
-6 20-22 34-36 25-29
-8 43-47 58-62 40-44
-10 55-65 100-110 57.5-62.5
-12 80-90 134-146 75-85
-16 115-125 202-218 109-121
-20 160-180 248-272 213-237
-24 185-215 303-327 238-262
-32 250-290 — 310-340
GATES BRAND FITTINGS
Dash Size 37 Degree JIC O-Ring (ORS) O-Ring Boss (ORB)
-4 10-11 10-12 14-16
-5 13-15 — —
-6 17-19 18-20 24-26
-8 34-38 32-40 37-44
-10 50-56 46-56 50-60
-12 70-78 65-80 75-83
-14 — 65-80 —
-16 94-104 92-105 111-125
-20 124-138 125-140 133-152
-24 156-173 150-180 156-184
-32 219-243 — —
AEROQUIP BRAND FITTINGS
Dash Size 37 Degree JIC O-Ring (ORS) O-Ring Boss (ORB)
-4 11-12 10-12 14-16
-5 15-16 — 18-20
-6 18-20 18-20 24-26
-8 38-42 32-35 50-60
-10 57-62 46-50 72-80
-12 79-87 65-70 125-135
-14 — — 160-180
-16 108-113 92-100 200-220
-20 127-133 125-140 210-280
-24 158-167 150-165 270-360
-32 245-258 — —

2-4 F-556-0910 Edition
STANDARD SPECIFICATIONS
Figure 2-1: Light Bracket Placement Assembly (2310-4-30)

STANDARD SPECIFICATIONS
2-5
Figure 2-2: Light Bracket Placement Assembly (2310-5-24)

2-6 F-556-0910 Edition
STANDARD SPECIFICATIONS
Figure 2-3: Light Bracket Placement Assembly (2310-5-30)

STANDARD SPECIFICATIONS
2-7
Figure 2-4: Light Bracket Placement Assembly (2310-6-24)

2-8 F-556-0910 Edition
STANDARD SPECIFICATIONS
Figure 2-5: Light Bracket Placement Assembly (2310-6-30)

STANDARD SPECIFICATIONS
2-9
Figure 2-6: Light Bracket Placement Assembly (2310-7-24)

2-10 F-556-0910 Edition
STANDARD SPECIFICATIONS
Figure 2-7: Light Bracket Placement Assembly (2310-7-30)

STANDARD SPECIFICATIONS
2-11
Figure 2-8: Light Bracket Placement Assembly (2310-8-30)

2-12 F-556-0910 Edition
STANDARD SPECIFICATIONS
Figure 2-9: Chopper Reel Placement (2310-4-30 & 2310-5-24)

STANDARD SPECIFICATIONS
2-13
Figure 2-10: Chopper Reel Placement (2310-5-30 & 2310-6-24)

2-14 F-556-0910 Edition
STANDARD SPECIFICATIONS
Figure 2-11: Chopper Reel Placement (2310-6-30 & 2310-7-24)