Landscape Forms Ashbery User manual

INSTALLATIONPROCEDURE:
Note:Thewallmountluminairemayalsobeconnectedtothewallmountbracketfirst,
andthentheassemblycanbeattachedtothebracketplate.
Toattachthebracketplatetothewall:
Note:Fornewinstallations,itisrecommendedthatasingle‐gangoutletboxbemounted
horizontallyinthewall.Theoutsidefaceoftheboxshouldbeflushwiththewallor
protrudenomorethan1/8”forbestresults.Sincewallmountingsubstratesvarygreatly,
theinstallershoulddeterminetheappropriatefastenerstousetoattachthebracketplate
tothewall.
1. Setbracketplateinpositiononthewall.SeeFig.3.
2. Markholelocations.Itisrecommendedthatatleast2oftheholesfromthetop5
locationsand2holesfromthebottom5locationsareusedforanchoring.
3. Movebracketplate.
4. Drillholesaccordingtoanchormanufacturer’srecommendations.
5. Runwiresthroughwiringaccessholeinbracketplate.
6. ApplybeadofsiliconetobackofbracketplateasshowninFig.4toensuretheplate
sealstothesingle‐gangboxandthewall.
7. Placebracketplateinpositionandinstallanchors.
Toattachwallmountbrackettobracketplate:
Note:Hardwareisincludedtoattachwallmountbrackettobracketplate.
1. Wallmountbracketisshippedpre‐wired.Makewiringconnectionsfromthewall
mountbrackettotheline‐involtagewires.
2. Setwallmountbracketinpositionoverbracketplate
3. AttachusingM8hexheadscrewsand5/16washersasshowninFig.5.
Toattachluminairetowallmountbracket:
Note:Hardwareisincludedtoattachluminairetobracket.
1. Connectthewiringharnessfromtheluminairetothewallmountbracketasshownin
Fig.1and2.
2. Pushexcesswireintothearmofthewallmountbracket.
3. Alignthearmoftheluminairelabeled“FRONT”oppositeofthearmofthewall
mountbracket.
4. Verifythatthewireswillnotpinchwhennestingtheluminaireintothewallmount
bracketcup.
5. InstalltheM10x45mmsocketheadcapsscrewsasshowninFig.6.
ToolsRequired
•Safetyglasses
•13mmsocketandratchetwrench
•8mmhexkey
•Wiringtoolsandconnectors
•Twistlockphotoeyecontrol,ifrequired
•Phillipsscrewdriver
•Hardwaretomountbracketplatetowall.Brackethas(10)Ø17/64”holestoallow
foranchoringinatleast4places–seeFig.3.Maxclearanceforanchorboltsis3/8”.
•Siliconesealer
WARNING! Installermustprovidestrainrelieftoline‐inwireswheretheyconnecttolight
fixturewires.Failuretodosomaycauseelectricalfailureandwillvoidwarranty.
LandscapeFormsisnotresponsibleforsitepreparation.
ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoat isastrong,long‐lastingfinish.To
protectthisfinishduringassembly,placeunwrappedpowdercoated partsonpackagingfoamor
othernon‐marringsurface.Donotplaceorslidepowdercoated partsonconcreteorotherhardor
texturedsurface– thiswilldamagethefinishcausingrusttooccur.Usetouch‐uppaintonany
gougesinthefinishcausedbyassemblytools.
Installation Guide
Ashbery Wall mount light
www.landscapeforms.com Ph: 800.521.2546
Date: October 27, 2017
Page 1 of 4
Includedcomponents
2X–M10x45mm
Sockethd
Capscrew
Wallmount
Bracket
Bracketplate
4X–M8x12mm
Hexheadbolt
Withthreadpatch
4X–5/16washer
Wallmt luminaire
NoTwist‐lock WithTwist‐lock
2X–M8x30mm
SocketHd CapScrew
Usedforwiringinspection

Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 2 of 4
Ashbery Wall mount light Date: October 27, 2017
Fig.3–Wallmountbracketdetails
WIRING
ACCESSHOLE
Fig.4–Wallmountsiliconelocation
HARDWARE
SHOWNFOR
REFERENCE
(NOTINCLUDED)
Fig.5– Attachwallmountbrackettobracketplate
Fig.1–wallmountluminairewiringcomponents
Fig.2– Wallmountluminairetobracketwiringconnection
Fig.6– Attachluminairetowallbracket

PROCEDUREFORWIRINGASHBERY:
TheAshbery luminaireisassembledatthefactory.Thelightcartridgeismountedintotheheadoftheluminaireandwillnotneedtobe removedduringinstallation.TheLED
cartridgeiswiredtothedriver(locatedinthebaseoftheluminaire)atthefactory.UseofLEDdriversotherthanthesuppliedunitisnotrecommendedandwillvoidthewarranty.
Thewiringschematicsreferenceconnectionsintheluminaireandconnector(s)usedtoattachtotheharnessinthewallmountbracket.Connectionhardwarenotincluded.
Installersareresponsibleforline‐inconnections.
Optionaldimmingcontrolisnotincluded.
Note:Thisunitispre‐wired.Thesediagramsareforreferencetothe3‐pinand2‐pinconnectors.
Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 3 of 4
Ashbery Wall mount light Date: October 27, 2017
WIRINGDIAGRAM:Type3luminaire,wallmount,notwist‐lockreceptacle WIRINGDIAGRAM:Type3luminaire,wallmount,withtwist‐lockreceptacle

INSTALLATIONPROCEDURE:
WARNING!Donothangorputadditionalloadonthelightfixtureonceitistippedout
andhangingforinspection.Damagetomountbracketorlightfixturemayoccur.
Toreadyunitforinspection:
1. RemovethetwobottomM8hexheadscrewsandwashers.
2. InstalltwoM8x30mmsocketheadcapscrewsinthetwobottomholesofthe
bracketuntiltheybottomout.
3. RemovethetopM8hexheadscrewswhilesupportingthelightfixturetokeepitfrom
tipping.
4. Slidethefixtureoutslowlyuntilitcontactstheheadsofthebottomtwoscrews.
5. Allowthefixturetoslowlytipforwarduntilitrestsonthebottomtwoscrews.
6. Hookup/Inspectthewiring.
7. Onceinspectioniscomplete,tipunitbacktolevelandslidebacktothebracket
mountplate.Ensurewiresarenotpinchedagainsttheboxorthebracket.
8. ReinstallthetwoM8hexheadscrewsandwashersatthetopofthebracket.
9. RemovethetwoM8socketheadcapsscrewsatthebottomofthebracketand
replacewiththeoriginalM8hexheadscrewsandwashers.
ToolsRequired
•6mmhexkey
•13mmsocketandratchetwrench
WARNING! Installermustprovidestrainrelieftoline‐inwireswheretheyconnecttolight
fixturewires.Failuretodosomaycauseelectricalfailureandwillvoidwarranty.
LandscapeFormsisnotresponsibleforsitepreparation.
ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoat isastrong,long‐lastingfinish.To
protectthisfinishduringassembly,placeunwrappedpowdercoated partsonpackagingfoamor
othernon‐marringsurface.Donotplaceorslidepowdercoated partsonconcreteorotherhardor
texturedsurface– thiswilldamagethefinishcausingrusttooccur.Usetouch‐uppaintonany
gougesinthefinishcausedbyassemblytools.
Installation Guide
Ashbery Wall mount light
www.landscapeforms.com Ph: 800.521.2546
Date: October 27, 2017
Page 4 of 4
Forinspectionpurposes:
2X–M8x30mm
SocketHd CapScrew
Usedforwiringinspection
Fig.7– Installspecialscrewsforwiringinspectionpurposes