Landscape Forms Torres User manual

SurfaceMount
ToolsRequired
•Safetyglasses
•Screwdrivers
•Wiringtoolsandconnectors
•1/2”wrenchorsocket
•Hammerdrill,with1/2”dia bit
•2mm,3mmand4mmhexkeys
•Epoxyanchoringsystemforconcrete
•Wirebrushandcompressedairforclearinganchorholes
ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoat isastrong,long‐lastingfinish.Toprotectthis
finishduringassembly,placeunwrappedpowdercoated partsonpackagingfoamorothernon‐marring
surface.Donotplaceorslidepowdercoated partsonconcreteorotherhardortexturedsurface– this
willdamagethefinishcausingrusttooccur.Usetouch‐uppaintonanygougesinthefinishcausedby
assemblytools.
LIGHTINGLAYOUTRECOMMENDATIONS:
Lightpolespacingistheresponsibilityofothers.RefertotheTorresPathLight
ProductDataSheet,availableonwww.landscapeforms.com,forlightdistribution
options.
Installation Guide
Torres Path Light, surface mount
www.landscapeforms.com Ph: 800.521.2546
Date: November 29, 2017
Page 1 of 3
Fig.2– Recommendedsetback
fromsidewalk
Includedhardware
4x–concrete
anchor
4x–5/16
washer
1x–path
lighttube
1x– luminaire
headwith
driverplate
1x–cover
plate
1x– luminaire
cover
4x–5/16‐18x
1”hexhd bolt
1x– anchor
template
4x–M6
tooth
lockwasher
4x–M6x
16mmsocket
buttonhead
capscrew
3x–M4x
20mmsocket
headcapscrew
2x–M4X10
Setscrew
Fig.1– Minimumfootingrecommendation
Fig.4–Baseplatedetail
[102mm]
4”dia.
ANCHORHOLE
BOLTCIRCLE
FRONT
OFLIGHT
2‐3/4”MAX
RECOMMENDED
CONDUITCLEARANCE 1/2”–3/4”
RECOMMENDED
CONDUITSIZE
Fig.3– Minimumconcreteslabsize
EDGEOR
EXPANSION
JOINT
[102mm]
4”MIN
[152mm]
6”MIN

LandscapeFormsisnotresponsibleforsitepreparationandfootings.Footingrecommendationsareincludedintheseinstructions.
Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 2 of 3
Date: November 29, 2017
HEXBOLT
5/16
WASHER
CONCRETE
ANCHOR
BASE
CASTING
Fig.6– Anchordetail
Fig.5– Assemblytemplateandanchors
HEXBOLT
5/16
WASHER
CONCRETE
ANCHOR
TEMPLATE
Fig.7–Installcoverplate
M6SOCKET
BUTTONHD
SCREW
TOOTH
WASHER
LUMINAIRE
HEADWITH
DRIVERPLATE
ATTACHED
Fig.8–Installluminaireanddriverplate
LUMINAIRE
COVER
M4SOCKET
HEADCAP
SCREW
Fig.9–Installluminairecover
INSTALLATIONPROCEDUREFORPATHLIGHT:
1. Preparefootingasrequiredbylocalcodes,seeFig.1,Fig.2andFig.3forrecommendations.
2. Setwoodenanchortemplateinpositionoverconduit. The‘F’onthetemplateindicatesthefrontoftheunit.
3. Markanchorholelocationsandremovethetemplate.
4. Drillholesaccordingtoanchorsizeanddepth,seeFig.6.Clearholesofdebris.
5. AttachanchorstowoodenanchortemplateasshowninFig.5.
6. Testfittemplateassemblywithanchorsintopositionbeforeinstallingepoxy.Makeanyadjustmentsasnecessarytoallow
concreteanchorstofreelyinstall.Concreteanchorshouldsitcenteredinholeandnotrestagainstthesideofthedrilledhole.
7. Addepoxytoanchorholesperepoxymanufacturer’srecommendations.
8. Slowlysettemplateassemblywithanchorsintoposition.Wipeawayanyexcessepoxybeforeitcures.
9. Allowepoxytofullycure.Removehexboltsandwashers.Removewoodentemplate.
10. SetsurfacemountpoleoverconcreteanchorsandattachusinghexboltsandwashersasshowninFig.6.Alignarrowonbase
platewithfrontlocationofpathlight.
11. Installcoverplateoverpole.Securewith2setscrews(included).Alignscrewswithtwoflatsidesofbaseplate.SeeFig.7.
12. Makewiringconnections(refertopage3)betweendriverplateandline‐insupplywiring,seeFig.8.
13. Secureluminaireanddriverplateassemblytopolewith(4)M6screwsandlocktoothwashers,seeFig.8.
14. Attachluminairecoverwith(3)M4screws,seeFig.9.
Torres Path Light, surface mount

PROCEDUREFORWIRINGPATHLIGHT:
Thefollowingschematicistobeusedtoconnecttheunittolinevoltage.Itisthe
responsibilityoftheinstallertomakesurethatallconnectionsaremadeinaccordance
withtheNECandlocalbuildingcodes.Connectionhardwarenotincluded.
INSTALLATIONANDSERVICESHOULDONLYBEPERFORMEDBYQUALIFIEDPERSONNEL.
Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 3 of 3
Date: November 29, 2017
Fig.10–Pathlightwiringschematic
Torres Path Light, surface mount