Landscape Forms Torres User manual

INSTALLATIONPROCEDURE:
Note:Thecatenaryluminaireshipsassembled.Supportingcableandline‐voltage
supplywiresarenotincluded.CableclampisdesignedforØ1/4”‐Ø1/2”cables.
CableglandsacceptsupplywiresbetweenØ0.24”– Ø0.47”.
1. Setluminaireonsupportingcable.SeeFig.1.
2. Installcableblocks,usingM6x35mmsocketheadcapscrews,tabbedwashers
andlocknutsasshowninFig.1.Tightensecurely.Oncetightened,bendtabs
downonwasherstoensurelocknutscannotloosen.
3. InstallM8x40mmhexheadscrew,washersandlocknutstolockverticalrotation,
seeFig.2.
4. Removeconnectionboxcover.Retainscrews.SeeFig.3.Leavelanyardand
screwsattachedtopreventcoverfromfalling.
5. Orientluminaireinthedesiredposition.Tightenlargenutinsideconnectionbox
tolockhorizontalrotation.Installsetscrewsonstemandtighten,seeFig.4.
6. Runelectricalsupplycable(notincluded)towiringconnectionboxandmake
wiringconnections,seeFig.5.
7. Ifonlyonesideoftheconnectionboxisneededforline‐inwires,removethe
unusedcableglandandreplacewiththethreadedplug.Tightensecurelywitha
wrench,seeFig.6.
8. Replaceconnectionboxcover.
ToolsRequired
•Safetyglasses
•10mmwrench
•13mmsocketandratchetwrench
•13mmboxwrench
•32mmwrench
•25mmwrench
•3mmhexkey
•4mmhexkey
•5mmhexkey
•Wiringtoolsandconnectors
•Pliers
•Flatbladescrewdriver
•Hangingcable,mindia.0.25”,maxdia.0.50”
WARNING! Installermustprovidestrainrelieftoline‐inwireswheretheyconnecttolight
fixturewires.Failuretodosomaycauseelectricalfailureandwillvoidwarranty.
LandscapeFormsisnotresponsibleforsitepreparation.
ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoat isastrong,long‐lastingfinish.To
protectthisfinishduringassembly,placeunwrappedpowdercoated partsonpackagingfoamor
othernon‐marringsurface.Donotplaceorslidepowdercoated partsonconcreteorotherhardor
texturedsurface– thiswilldamagethefinishcausingrusttooccur.Usetouch‐uppaintonany
gougesinthefinishcausedbyassemblytools.
Installation Guide
Torres Catenary light
www.landscapeforms.com Ph: 800.521.2546
Date: June 6, 2019
Page 1 of 4
Includedcomponents
2X–M6x8mm
Hexhead
Setscrew
2X–cableblocks
4X–M6x1x35mm
Sockethd
Capscrew
4X–M6x1
Nylonlocknut
1X–luminaire
assembly
1X– threaded
plug
2X–M8x1.25x
40mm
Hexheadscrew
2X–M8x1.25
Nylonlocknut
4X–M8
washer
2X– tabbed
washer

Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 2 of 4
Torres Catenary light Date: June 6, 2019
Fig.1– Installluminaireonsupportcable
SUPPORTCABLE
(NOTINCLUDED)
M6x1x35mm
SOCKETHEAD
CAPSCREW
BLOCK
TABBED
WASHER
M6NYLON
LOCKNUT
Fig2– Installboltstolockverticalrotation
M8WASHER
M8NYLON
LOCKNUT
M8WASHER
M8x1.25x40mm
HEXHEAD
SCREW

Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 3 of 4
Torres Catenary light Date: June 6, 2019
Fig.3–Removeconnectionboxcover
CONNECTION
BOXCOVER
PLATE
REMOVE
USING
4mmHEXKEY
Fig.4–lockhorizontalrotation
TIGHTENNUT
TIGHTENWITH
3mm HEXKEY

Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 4 of 4
Torres Catenary light Date: June 6, 2019
Fig.5–makeelectricalconnections
ELECTRICAL
SUPPLYCABLE
(SUPPLIEDBY
OTHERS)
Fig.6– Installthreadedplug,ifcableglandisnotused
ELECTRICAL
SUPPLYCABLE
(SUPPLIED
BYOTHERS)
THREADED
PLUG
PROCEDUREFORWIRING:
TheTorrescatenaryluminaireispre‐wiredandassembledatthefactory.The
lightcartridgeismountedintotheheadoftheluminaireandwillnotneedtobe
removedduringinstallation.Line‐inanddimmingwireleadstodriverare
providedinwiringconnectionbox.TheLEDcartridgeiswiredtothedriveratthe
factory.UseofLEDdriversotherthanthesuppliedunitisnotrecommendedand
willvoidthewarranty.
Thewiringschematicsreferenceconnectionsintheluminaireandconnector(s)
usedtoattachtotheharnessintheconnectionbox.Connectionhardwarenot
included.
Installersareresponsibleforline‐inconnections.
Note:Thisunitispre‐wired.Allwiringconnectionsaremadeinsidethe
connectionbox.Theluminaireshouldnotbedisassembled.
WIRINGDIAGRAM:Catenaryluminaire