Landscape Forms Typology User manual

Included components
ASSEMBLE WITH CARE! Pangard IIPolyester Powdercoat is a strong, long-lasting finish. To
protect this finish during assembly, place unwrapped powdercoated parts on packaging foam or
other non-marring surface. Do not place or slide powdercoated parts on concrete or other hard or
textured surface –this will damage the finish causing rust to occur. Use touch-up paint on any
gouges in the finish caused by assembly tools.
Landscape Forms is not responsible for site preparation and footings. Footing
recommendations are included in these instructions.
LIGHTING LAYOUT RECOMMENDATIONS:
Refer to the Typology Path Light product data sheet at www.landscapeforms.com for
more information.
Fig. 1 –Minimum footing recommendation
Tools Required
•Safety glasses
•Screwdrivers
•Wiring tools and connectors
•Masonry drill, with Ø1/2” bit
•Compressed air and wire brush
•Epoxy anchoring system for concrete
•1/2” socket wrench
•5/32” hex key
Installation Guide
Typology Path Light
www.landscapeforms.com Ph: 800.521.2546
Date: March 21, 2022
Page 1 of 3
Fig. 2 –Minimum concrete slab size
HEX BOLT AND
WASHER
CONCRETE
ANCHOR
EDGE OR
EXPANSION
JOINT
Fig. 3 –Assemble anchor template
HEX BOLT
WASHER
TEMPLATE
CONCRETE
ANCHOR
Single Double
4x – 5/16-
18 concrete
anchor
4x – 11/16
OD washer
4x – 5/16-
18 x 1” HEX
BOLT
1x – unit
body
single
1x –
anchor
template
1x – unit
body
double
2x – concrete
panel double
1x – concrete
panel single
1x – concrete
panel single
Included hardware
Fig. 5 –Recommended
setback from sidewalk
SIDEWALK
Fig. 4 –Proper orientation
of conduit
CONDUIT
FRONT OF
LIGHT

INSTALLATION PROCEDURE FOR PATH LIGHT:
1. Prepare footing as required by local codes, see Figs. 1, 2, 5 for recommendations. Run line-in voltage wires up
through conduit with at least 12” excess wires.
2. Set wooden anchor template in position over conduit. ‘FRONT’ on the template indicates the Front of the unit.
3. Mark anchor hole locations, move the template.
4. Drill holes according to Fig. 2. Clear holes of debris.
5. Assemble the template, concrete anchor, washer and hex bolt as shown in Fig. 3.
6. Test fit anchors into holes. Make any adjustments to the holes as necessary to allow anchors to freely install.
Anchors should sit centered in hole and not rest against the sides or bottom of the drilled holes.
7. Fill holes with epoxy per epoxy manufacturer’s recommendations.
8. Slowly set anchor template assembly into the holes. Wipe away any excess adhesive. Allow epoxy to cure.
9. Remove hex bolts and washers. Remove template.
10. Set unit in place, ensuring that base is sitting flat on concrete.
11. Install hex bolts and washers.
12. Remove driver plate cover, see Fig. 6.
13. Connect line-in voltage wires to driver wires, see Fig. 6. Recommended waterproof connectors provided by
others.
14. Replace driver plate cover.
15. Remove top plate from unit body, see Fig. 7. Retain hardware.
16. Ensure two foam blocks are adhered to each concrete side panel. Install concrete side panels, see Fig. 8 and
Fig. 9. Set panel up to unit body and slide down so both tabs on panel engage on receivers on unit body.
Gently pull out at bottom of concrete panel to ensure bottom tab is engaged. Note orientation of notch in
panel for single path light units.
17. Reinstall top plate, see Fig. 10
PROCEDURE FOR WIRING:
The Typology path light is assembled at the factory. The light cartridge is mounted into the head of the pole and
will not need to be removed during installation. The LED cartridge is wired to the driver (located in the unit body)
at the factory.
The following schematic is to be used to connect the unit to line voltage. It is the responsibility of the installer to
make sure that all connections are made in accordance with the NEC and local building codes. Connection
hardware not included.
WARNING!: LED cartridge and driver are not rated for connection or disconnection while energized. Doing so may
damage LEDs and will void the warranty. Disconnect incoming power before making or breaking any electrical
connections.
Installation Guide
Typology Path Light
www.landscapeforms.com Ph: 800.521.2546
Page 2 of 3
Date: March 21, 2022
CAUTION! Fixtures and wiring must be installed in accordance with local codes and ordinances.
NOTES: Landscape Forms is not responsible for site preparation, footings, or electrical wiring..
Fig. 6 –Access panel removed
LINE IN
WIRES
SCREW
Fig. 7 –Remove top plate
SCREW
TOP
PLATE

Installation Guide
Typology Path Light
www.landscapeforms.com Ph: 800.521.2546
Page 3 of 3
Date: March 21, 2022
Fig. 11 –single luminaire wiring diagram
Fig. 9 –Detail of panel attachment
RECEIVER
BLOCK
ON UNIT
BODY
RETAINER
TAB ON
CONCRETE
PANEL
Fig. 10 –Reattach top plate
TOP
PLATE
SCREW
Fig. 12 –double luminaire wiring diagram
Fig. 8 –Detail of panel attachment
RECEIVER
BLOCK
ON UNIT
BODY
RETAINER
TAB ON
CONCRETE
PANEL
CONCRETE
PANEL
RETAINER
TAB ON
CONCRETE
PANEL
FOAM
BLOCKS ON
CONCRETE
PANEL
RECEIVER
BLOCK
ON UNIT
BODY