Lanpro LP-1521 User manual

Wireless - Equipment
www.lanpro.com
LP-1521 Broadband AP Router. 123 Manual
Installation in AP Router mode, (with PoE).
LP1521_M123_ENG01W
LP-1521 Broadband AP Router.
123 Manual
Installation in AP Router mode,
(with PoE).

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-1521 Broad Band AP Router (AP Router mode, with PoE).
2
Figure 1
Open your preferred Browser application with the
Router´s default IP address 192.168.1.254 as shown
in figure 6.
6
Figure 6
Figure 2
Figure 3
Figure 4
Figure 5
Please check the package contents, please see Figure 1.
1
Screw the antenna as shown in figure 2.
2
The LP-1521 can be powered in three different ways:
A.-Via passive PoE: through any of the following
ports: WAN, LAN1 and LAN4 . The RJ45 Pins used
are: Pin 5 ( -12 VDC) and Pin 7 (+12 VDC). You
must include a Passive Injector and a power converter
supplying between 12 and 22 VDC and power the
LP-1521 through distances up to 40 m.
B.-Via active PoE: you can use the LP-PoE150
injector and LP-PoE151 splitter made by Lanpro. This
arrangement will let you put the LP-1521 as far as
100 m from the injector. You must set the splitter to
12 VDC and power the LP-1521 through the power
Jack.
C.- Via the Jack placed at the right of the LAN4 port.
We have provided with this kit a way to power the
LP-1521 by using a 120 VAC to 12 VDC Power
Converter included in the box and shown in figure 5.
5
Connect your PC to a LAN port of the LP-1521 as
shown in figure 3.
3
Connect your ISP cable to the WAN port as shown in
figure 4 (ISP: Internet Service Provider).
4

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-1521 Broad Band AP Router (AP Router mode, with PoE).
In the window shown in figure 7, select: Operation
Mode, select: Gateway, finally select:
Apply Changes.
7
Figure 7
3
Once changes are applied, the window shown in figure
8 pops-up:
Please select: OK.
8
Figure 8
In the window shown in figure 9, select: Wireless,
Basic Settings, in: Mode, select: AP, then, select:
Apply Changes, the equipment will restart.
9
Figure 9
Steps to follow for Router Mode set-up
If you wish that your equipment delivers IP addresses
to the clients that connect to it, please proceed in the
window shown in figure 10 to select: TCP/IP Settings,
LAN interface and in: DHCP, select: Server and then:
Apply Changes. In the AP mode, please take in mind
that if another equipment delivers also IP addresses,
they shouldn’t enter into conflict.
10
Figure 10

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-1521 Broad Band AP Router (AP Router mode, with PoE).
4
Please change the administrator password of your
equipment. In figure 13, select: Management, then:
Password, input the user name: admin, input a new
key in: New Password and repeat it in: Confirmed
Password, select: Apply changes, please remember
these username and password as the equipment will
ask for them from now on.
13
Important advice (optional).
Figure 13
In the window shown in figure 11, please select:
TCP/IP Settings, WAN interface and configure the
properties of your service provider. The ISP’s have a
default setting as DHCP Client, hence there is no need
for changing it.
Please take in mind that the option: Attain DNS
Automatically is selected.
11
Figure 11
You should now configure the wireless connection
security. In order to do that, please select: Wireless,
Security in the window shown in figure 12. In the
Encryption mode we reccomend you use: WPA2
Mixed. Please verify that the clients of this router
support this mode. If not, choose another, like
WPA(TKIP) and proceed to input in: Pre-Shared Key
the key for that network which should be at least of 8
characters in lenght. Finally, select: Apply changes
and the equipment will be restarted.
12
Figure 12