Lanpro LP-N24 User manual

Wireless - Equipments
www.lanpro.com
123 Manual, LP-N24 V2.0, 2.4 GHz Wireless-N Broadband Router
and/or Access Point (AP). Router and Access Point mode installation.
LPN24V2_M123_ENB01W
123 Manual, LP-N24 V2.0,
2.4 GHz Wireless-N
Broadband Router
and/or Access Point (AP).
Router and Access Point
mode installation.

www.lanpro.com
2
Wireless - Equipments - 123 Manual - LP-N24 V2.0 - 2.4 GHz Wireless-N Broadband Router
and/or Access Point (AP) - Router and Access Point mode installation.
3
Screw the antenna as shown in Figure 2.
Connect to electric power as shown in Figure 3.
2
3
Figure 3
Figure 2
Check the content of the box as shown in Figure 1.
1
Figure 1

www.lanpro.com
3
Wireless - Equipments - 123 Manual - LP-N24 V2.0 - 2.4 GHz Wireless-N Broadband Router
and/or Access Point (AP) - Router and Access Point mode installation.
Connect your computer to a LAN port of the LP-N24 V2.0
as shown in Figure 4.
Connect your Internet service to the WAN port as shown in
Figure 5.
Make sure that your network card obtains the IP address
automatically. For this, you should see the properties of your
network card and check the values, as shown in Figure 6.1
and 6.2. Once you have nished, select Ok twice.
4
5
6
Figure 4
Figure 5
Figure 6-1 Figure 6-2
7
Open the web browser of your preference and type the
default address: 192.168.0.1 as shown in Figure 7.
Figure 7

www.lanpro.com
4
Wireless - Equipments - 123 Manual - LP-N24 V2.0 - 2.4 GHz Wireless-N Broadband Router
and/or Access Point (AP) - Router and Access Point mode installation.
5
9
10
11
In the initial window, you may type the password of your
wireless network in Security key eld, and then select Ok
as shown in Figure 9. This step along with the typing of
the security key is enough to establish the security in your
computer. In addition, in the initial window you can select
the ISP connection type (WAN port), which is DHCP by
default for most of the ISP. Do not forget to select Ok when
you nish.
If you want to congure the additional security settings, as
key type and encryption or WAN connection type, please
select Advance Settings as shown in Figure 10.
Click on Advance Settings / WAN settings to select the
options corresponding to your internet service provider
(most of these providers use DHCP). Select Ok as shown in
Figure 11.
Figure 9
Figure 10
Figure 11
8
In case of your router has a password, a window will appear
asking for it. Please, type it and select Ok as shown in
Figure 8.
Figure 8

www.lanpro.com
5
Wireless - Equipments - 123 Manual - LP-N24 V2.0 - 2.4 GHz Wireless-N Broadband Router
and/or Access Point (AP) - Router and Access Point mode installation.
12
13
14
Proceed to type the name of your wireless network. Click
on Wireless settings / Wireless Basic Settings. In
the SSID eld, type the name you want for your wireless
network. Then select Ok, as shown in Figure 12.
To choose the security mode, select Wireless settings /
Wireless Security. We recommend you to use WPA-PSK.
Type the key for wireless clients. Select Ok as shown in
Figure 13.
Finally, change the security key of your computer. To do
so, select System tools / Change password. On Old
password eld type the previous password. If this is the
rst time, leave that eld in blank. In New password and
Conrm new password, type the key and select Ok,
as shown in Figure 14. Remember to save this password
in a safe place because it can be required in case you want
to log in again.
Figure 12
Figure 13
Figure 14