Lanpro LP-N24 User manual

Wireless - Equipment
www.lanpro.com
LP-N24 Router and AP Mode Setting 123 Manual
(without installation CD).
LPN24_M123_ENB01W
LP-N24
Router and AP Mode Setting 123 Manual
(without installation CD).

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-N24 Router and AP Mode Setting 123 Manual (without installation CD)
2
The purpose of this 123 Manual is as a substitute to the Wizard included in the CD that comes in the package.
Figure 1
Figure 2
Figure 3
1
2
3
Please review package contents, Figure 1.
Connect electric power to the router as shown in gure 2.
Connect your PC to one of the LAN ports of the LP-N24 as
shown in gure 3.

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-N24 Router and AP Mode Setting 123 Manual (without installation CD)
3
Figure 4
Figure 5 Figure 6
4
5
6
Connect you Internet Access connection to the WAN port as
shown in gure 4.
Please verify that your network communication card obtains the IP address automatically. In order to do this, go to your
Local Area Connection network card then select: Properties to verify the values as shown in gures 5 and 6.
Once nished, select: Ok then again: Ok.

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-N24 Router and AP Mode Setting 123 Manual (without installation CD)
4
7
8
9
Please open your browser and navigate to the default address of the router:192.168.0.1, as shown in gure 7.
A new window will pop-up asking for the user and the password. The default user is: admin, the password is: admin.
Select: OK, as shown in gure 8.
The conguration window will pop-up. You should select then option: Next, as shown in gure 9.
Figure 7
Figure 8
Figure 9

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-N24 Router and AP Mode Setting 123 Manual (without installation CD)
5
10
11
12
Please select option corresponding to your ISP (Internet
Service Provider). Most of them use the Dynamic IP address
option. Now select: Next as shown in gure 10.
Select: Apply to save the changes, as shown in gure 11.
A window showing the WAN connection status will pop-up. It
will obtain the WAN connection status. It will also obtain an
IP address like in gure 12 (The IP address of the example
is for reference purposes), if not, please verify that the WAN
cable of the LP-N24 is properly connected to the ADSL or
your ISP (Internet Service Provider). You can also turn off
and then on the ADSL Modem, wait 2 minutes and then
select option: Release and then select option: Renew as
shown in the window of the LP-N24 shown in gure 12.
Figure 10
Figure 11
Figure 12

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-N24 Router and AP Mode Setting 123 Manual (without installation CD)
6
13
14
15
Proceed to input the name of your Wireless network by
selecting option: WLAN Settings, Basic Settings and the
name you wish in the: SSID eld, then select: Apply, as
shown in gure 13.
Proceed to set the Security mode by selecting option: WLAN
Settings, Security Settings, in: Security Mode select the
mode desired. We recommend using: WPA2 –Personal and
proceed to select: Apply as shown in gure 14.
Proceed to input the wireless LAN password in: Pass Phrase
and select: Apply as shown in gure 15.
Figure 13
Figure 14
Figure 15

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-N24 Router and AP Mode Setting 123 Manual (without installation CD)
7
16
Finish by changing the administration password of your equipment. In order to do this, please select option: System Tools,
Change Password, input the password in: New Password and the password conrmation in: Re-enter to Conrm and
then select: Apply as shown in gure 16, remember to store it in a safe place because the equipment will ask for it in case
you wish to access the equipment again.
Figure 16