Larson Electronics EPL-AMB-150LED-150-140DB User manual

EPL-AMB-150LED-150-140DB
Larson Electronics, LLC Fax: [phone] www.larsonelectronics.com
1of 2
150W Explosion Proof LED Light Fixture
17,500 Lumens - 150' Cord - Adjustable Magnet Base - 140°
Instruction Manual
This explosion proof light is designed for illumination of industrial locations. It uses the latest in
solid state lighting technology for long life, low maintenance and high efficiency.
The unique design focuses the light where it is needed, giving improved efficiency over a
conventional HID luminaire.
An internal, universal input, power-factor-corrected switch-mode supply allows it to be used from any
nominal 120-277V AC 50/60 Hz power supply without any variation in light output.
WARNING
To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected
and maintained by a qualified electrician only, in accordance with all applicable electrical codes.
To avoid electric shock:
Be certain electrical power is OFF before and during installation and maintenance.
Luminaire must be connected to a wiring system with an equipment-grounding conductor.
To avoid explosion:
Make sure the supply voltage is within the luminaires’ voltage rating.
Ensure the marked T rating is less than the ignition temperature of the Hazardous
Atmosphere.
Do not operate in ambient temperatures above those indicated on the luminaire nameplate.
Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
For supply connections, use wire rated for at least 110°C
Recommended mounting height is 25-40 feet.
MAGNETIC MOUNTING
The magnetic mounting bracket includes eight 100lbs grip magnets for mounting to metal surfaces.
The magnets are arranged in groups of two via adjustable brackets allowing operators to match the
curvature of tank walls or other curved surfaces.
Simply adjust the magnets as needed and attach to a metal surface capable of holding the weight of
the light. The magnetic brackets can be loosened at the adjustment points for easier maneuvering
while mounting.
To adjust the light head vertically, loosen the hand screws on either side. Once the desired angle is
achieved, tighten both hand screws to secure the light in place.
This bracket system is constructed of non-sparking aluminum for light weight and durability. The
simple swing hinge design allows operators to easily adjust the lamp assembly to position the unit as
a pedestal lamp if desired.
Phone: [phone]

EPL-AMB-150LED-150-140DB
Larson Electronics, LLC Fax: [phone] www.larsonelectronics.com
2of 2
WIRING (see attached wiring diagram)
This unit comes preconfigured with selected cord cap, voltage, and beam angle. Once mounted, plug
cord into compatible receptacle with correct voltage as listed on fixture nameplate.
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool
down before performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens
will void the warranty.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend
routine checks to be made on a yearly basis. Frequency of use and environment should
determine this. It is recommended to follow an Electrical Preventive Maintenance Program
as described in NFPA 70B: Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric
performance. Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use
mild soap or a liquid cleaner.
3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions
or contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if
needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER
INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT [e-mail] OR BY PHONE AT
1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
WARNING: CHECK NAMEPLATE
FOR PROPER VOLTAGE. DAMAGE
FROM IMPROPER VOLTAGE WILL
VOID WARRANTY.
Phone: [phone]