Larson Electronics HAL-MB-185LED-CPR-100 User manual

HAL-MB-185LED-CPR-100
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
185 Watt Hazardous Location LED Light - Magnetic
Mount - C1D2 - ATEX - 100 foot Cord w/ EXP Plug
Instruction Manual
This explosion proof light is designed for illumination of industrial locations. It uses the latest in solid state
lighting technology for long life, low maintenance and high efficiency.
The unique design focuses the light where it is needed, giving improved efficiency over a conventional
HIDluminaire.
An internal, universal input, power-factor-corrected switch-mode supply allows it to be used from any
nominal 90-305V AC, 50/60Hz supply without any variation in light output.
WARNING
To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected and
maintained by a qualified electrician only, in accordance with all applicable electrical codes.
To avoid electric shock:
Be certain electrical power is OFF before and during installation and maintenance.
Luminaire must be connected to a wiring system withan equipment-grounding conductor.
To avoidexplosion:
Make sure the supply voltage is within the luminaires’ voltage rating.
Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere.
Do not operate in ambient temperatures abovethose indicated on the luminaire nameplate.
Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.
MOUNTING
This explosion proof LED light fixture is comprised of a 16x14 inch LED light head mounted atop a legged
base stand fabricated from non sparking aluminum, with a separate shelf type magnetic mounting
bracket that allows mounting to ferrous metallic surfaces. The lamp can be easily adjusted up or
down 90 degrees and locked into position by simply loosening the two T-handle adjustment screws
located on either side of the light head and retightening them once the desired angle is found. The
magnetic mounting bracket for this unit includes six 200 lbs. grip magnetic bases which provide a total of
1,200 lbs. of grip and allows operators to mount the unit to walls and flat metallic surfaces. Users simply
attach the magnetic mounting bracket to the desired surface, then hang the lamp assembly from the
bracket.
WARNING: If there is moisture present, or chance of it, in the conduit system then necessary
precautions should be taken by the installer to prevent the moisture from entering through the cable or
conduit and entering the fixture. Failure to comply with the above could void the warranty.

HAL-MB-185LED-CPR-100
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
WIRING (see attached wiring diagram)
This unit comes preconfigured with selected cord cap. The is outfitted with 100` of 16/3 chemical and
abrasion resistant SOOW cord that is fitted with an explosion proof cord cap for easy connection to
explosion proof outlets. Plug options include a 5-15 15 amp straight blade plug for use with 120V
explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets,
or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof outlets. **PLEASE
NOTE** voltage ratings on plugs and outlets are MAXIMUM voltage. For low voltage applications,
proper voltage must be applied to the outlet or damage to the light fixture will occur.
MAINTENANCE
Caution: To avoidpersonal injury, disconnect power to the light and allow the unit to cool down before
performing maintenance.
Warning:No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will
voidthe warranty.
1. Perform visual,mechanical and electrical inspections on a regular basis. We recommend routine
checks to be made on a yearly basis. Frequency of use and environment should determine this. It
is recommendedto follow an Electrical Preventive Maintenance Program as described in NFPA
70B: Recommendedpractice for Electrical Equipment.
2. The lens should be cleaned periodically as neededto ensure continued photometric performance.
Clean the lens with a damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid
cleaner.
3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e.excessive dust build-up). Clean with a non-abrasive cloth if
needed.
4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER
INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT [email protected] OR BY PHONE AT
1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.