LaserLiner Quadrum OneTouch User manual

Quadrum OneTouch / Quadrum OneTouch Green
DE
02
GB
13
NL
24
DK
35
Laser
530-670 nm
man
IP 66
FR
ES
IT
PL
FI
PT
SE
46
57
68
79
90
101
112
NO
TR
RU
UA
CZ
EE
LV
LT
RO
BG
GR
123
134
145
156
167
178
189
200
211
222
233
auto
Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 1 10.03.11 08:58

13
Quadrum OneTounch / Quadrum OneTounch Green
Caution: Prior to using the laser, you must read the safety instructions for
laser class 3R thoroughly. Warning signs must not be removed from the laser
measuring device! Do not look directly into the beam. Lasers must be kept
out of reach of children. Never intentionally aim the device at people. This is a
quality laser measuring device and is 100% factory adjusted within the stated
tolerance. For reasons of product liability, we must also draw your attention
to the following: Regularly check the calibration before use, after transport
and after extended periods of storage. We also wish to point out that absolu-
te calibration is only possible in a specialist workshop. Calibration by yourself
is only approximate and the accuracy of the calibration will depend on the
care with which you proceed.
Laser radiation!
Avoid direct exposure
to the eyes.
Laser class 3R
< 5 mW Ċ530 - 670 nm
EN60825-1:2007-10
General safety instructions
Please read the operating instructions as well as the enclosed
brochures "Guarantee and additional notices" and "Laser class 3R
safety instructions". Follow the instructions they contain. Safely
keep these documents for future reference.
!
Fully automatic rotary laser with red or green laser
technology.
– Laser modes: spot, scan, rotary and hand receiver mode
– All functions can be controlled remotely.
– optional SensoLite 310: Laser receiver range up to 300 m radius
– optional SensoLite 410: Laser receiver range up to 400 m radius
– optional SensoMaster 400 (Quadrum red only): Laser receiver range in
excess of 300 m radius. With longer laser receiver unit and millimetre exact
distance reading for laser level.
GB
Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 13 10.03.11 08:58

14
Special product features and functions
The rotary laser starts up by rotating and aligning itself
automatically. It is set to the required initial position (to within an operating
angle of ± 5°) and the automatic system then performs the necessary fine
adjustment, with two electronic measurement sensors detecting the X and
Y axes.
The anti-drift system (ADS) prevents erroneous or inaccurate
measurements. How it works: The laser automatically switches to active
ADS mode 35 seconds after being switched on and is permanently checked
to ensure it is aligned correctly. If the device moves due to the influence of
external factors or the laser loses its height reference, the laser will come to
a standstill. Additionally, the laser flashes and the tilt LED is lit continuously.
To continue working switch the device off and on again. Erroneous and
inaccurate measurements are thus prevented simply and reliably.
ADS is automatically active after the device is switched on in order to prevent
changes in position caused by external influences affecting the set-up device. The
tilt LED flashes to indicate that the ADS function is active; see the diagram below.
Press the ON/OFF button for 3 seconds to switch off the ADS function.
ON:
Rotation begins External
influence
Adjustment phase
Sensor Automatic,
X and Y LEDs flashing
X and Y LEDs
permanently on The
laser
remains stationary as
a precaution, the laser
flashes and the tilt
LED is lit continuously.
ADS active after
35 seconds, rapid
flashing of the tilt LED.
ADS function
The ADS does not activate the monitoring function until 35 seconds
after the laser levelling procedure has been completed (set-up phase).
The tilt, X and Y LEDs flash during the set-up phase; the tilt LED flashes
rapidly and the X and Y LEDs are permanently on when ADS is active.
!
GB
Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 14 10.03.2011 17:02:25 Uhr

15
Quadrum OneTounch / Quadrum OneTounch Green
Transport LOCK: The device is protected by a special motor
brake during transport.
IP 66
The device characterised by specific protection against
dustand rain.
Quadrum OneTouch Green: green laser technology
The distance at which a laser is visible to the naked eye depends on its colour
i.e. wavelength. This is because of the human eye's physiology – green
appears brighter to us than red. Depending on ambient light, green lasers
are therefore many times more visible than red lasers; in indoor areas this is
as much as 12 times brighter. This permits applications on dark surfaces, over
longer distances and work in very bright ambient light. A red laser with a 635
nm wavelength is used as a reference value for brightness differentiation.
In contrast to red lasers, green laser light can only be produced indirectly.
This is a source of potential characteristic fluctuations:
– The optimal operating temperature is 20°C. Outside its operating
temperature range of 0 – 40°C Quadrum OneTouch Green is darker.
IMPORTANT: Allow the unit enough time to adapt to the ambient
temperature before switching the unit on.
– Laser brightness may vary somewhat from one unit to another. This is a
natural phenomena and excluded from warranty claims.
– Green Laser will only work with certain Receivers. The maximum range
of the Receiver is shorter, please refer to technical details.
Horizontal
levelling Slope function
auto man
Space grids: These show the laser planes and functions.
auto: Automatic alignment / man: Manual alignment
GB
Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 15 10.03.11 08:59

16
+
C
–
+
C
–
+
C
–
+
C
–
+
AAA
–+
AAA
–
Battery charging
– Charge the device's battery completely prior to use.
– Connect the charger to mains power supply and the charging socket (H) of
the battery compartment (J). Please only use the charger supplied; using a
different charger will invalidate the warranty. The rechargeable battery can
also be charged when it is not inserted in the device.
– When the rechargeable battery is being charged, the LED on the charger (L)
lights up red. When the LED changes to green, charging is complete. When
the unit is not connected to the charger the power charger's LED lamp will
blink.
– Alkaline batteries (4 x type C) can be used as
an alternative. Insert them in the battery com-
partment (I) as per the installation symbols.
– Insert battery (J) / battery compartment (I) into
slot (E) and secure it in place with fastening
screw (G). The electrical contacts (F) must be
connected.
– With the rechargeable battery inserted, the
device is ready to run even during charging.
– When all 4 LEDs (2, 4, 5, 6) light up briefly and
the device switches off, the batteries must be
replaced or the rechargeable battery charged.
Insert batteries into the remote control
– Observing the correct polarity.
GB
I
J
H
G
F
E
Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 16 10.03.11 08:59

17
Quadrum OneTounch / Quadrum OneTounch Green
G
F
H
A
B
C
D
E
F
G
H
I
J
K
L
Prism head / laser beam outlet
Receiver diodes for remote
control (4 x)
Control panel (ON/OFF button)
5/8" thread (bottom)
Slot for rechargeable battery /
battery compartment
Electrical contacts
Battery compartment / battery
fastening nut
Charging socket
Battery compartment
Rechargeable battery
compartment
Mains unit / charger
Operation indicator
red: battery is charging
green: charging process complete
GB
A
B
C
J
K
I
F
L
D
E
Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 17 10.03.11 08:59

18
1
14
16
17
8
11
13
12
9
10
15
23
4675
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
auto/man function
auto/man function LED
LED off: automatic alignment
LED on: manual alignment
ON/OFF button
X axis LED
Tilt function LED
Y axis LED
Battery display
Rotary speed for selection, 600 /
300 / 120 / 60 / 0 rpm
Positioning button
(rotate to the right)
Positioning button
(rotate to the left)
auto/man. function:
Y axis proceed as above
auto/man. function:
Y axis proceed as below
auto/man. function:
X axis proceed as above
auto/man. function:
X axis proceed as below
Scan mode
Operation indicator
Infrared signal emitter
Control panel
Quadrum OneTouch Remote control
GB
Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 18 10.03.11 08:59

19
Quadrum OneTounch / Quadrum OneTounch Green
XY
±5°
man
If the device has been placed on a surface with too much of a slope
(more than 5°), the prism head remains stationary and the laser starts
to flash. The device must then be placed on a more even surface.
!
auto/man function LED OFF: Automatic alignment
!
– The device levels itself automatically to within a range of ±5°. The laser
rotates and the tilt, X and Y LEDs flash during the set-up phase. When
levelling is complete, the tilt LED flashes rapidly and the X and Y LEDs are
permanently on. The laser rotates at maximum speed. Refer also to the
sections about "Sensor Automatic" and "ADS Tilt".
Horizontal levelling
– Horizontal: Position the device on a level surface or
on a tripod.
– Press the "ON/OFF" switch
auto
Slope function up to 5° – horizontal
This function deactivates the automatic sensor. To use the function, press the
auto/man button. The plus/minus buttons are used to re-adjust the slope by
means of a motor. In the process the X-and Y-axis can be adjust separately.
Refer to the illustrations below.
GB
Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 19 10.03.11 08:59

20
man
Slope function > 5°
Steeper slopes can be set using the angle plate,
which is available as an optional extra (product
ref. 080.75). TIP: Allow the device to align itself
automatically and set the angle plate to the zero
position. Then press the auto/man button to switch
the automatic sensor off. Finally, incline the device
to the angle you require.
auto/man function LED ON: Manual alignment
!
Laser modes
Rotary mode
The following speeds can be set using the rotary
button: 0, 60, 120, 300, 600 rpm
Spot mode
You access spot mode by pressing the rotary
button repeatedly until the laser stops rotating.
The laser can then be positioned exactly at the
measuring point by means of the direction
buttons.
Scan mode
The scan button can be used to activate and set
a lightintensive segment in 4 different widths.
You position the segment via the direction
buttons.
Hand receiver mode
Working with the laser receiver (available as an
optional extra): Set the rotary laser to maximum
speed and switch on the laser receiver. Refer to
the operating instructions for the respective laser
receiver about this.
GB
Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 20 10.03.11 08:59

21
Quadrum OneTounch / Quadrum OneTounch Green
EU directives and disposal
This device complies with all necessary standards
for the free movement of goods within the EU.
This product is an electric device and must be collected
separately for disposal according to the European
Directive on waste electrical and electronic equipment.
Further safety and supplementary notices at:
www.laserliner.com/info
GB
Technical data (Subject to technical alterations)
Self-levelling range ± 5°
Accurancy ± 0,75 mm / 10 m
Horizontal levelling Automatic with electronic
sensors and servo motors
Self-levelling alignment time Approx. 35 seconds over the
entire operating angle
Rotation speed 0, 60, 120, 300, 600 RPM
Remote control Infrared IR
Laser wavelengths green / red 635 nm / 532 nm
Laser class red / green 3R (EN60825-1:2007-10)
Laser output rating red / green < 5 mW
Power supply High-performance rechargeable
battery / batteries (4 x type C)
Rechargeable battery life red / green approx. 35 h / approx. 14 h
Non-rechargeable battery life red / green approx. 50 h / approx. 8 h
Battery recharging time ca. 6 h
Operating temperature red / green -10°C ... + 50°C / 0°C ... + 40°C
Storage temperature -10°C ... + 70°C
Protection class IP 66
Dimensions (W x H x D) /
Weight (incl. batteries) 215 x 205 x 165 mm / 2,6 kg
Remote control
Power supply 2 x type AAA
Remote control range max. 30 m (IR-Control)
Weight (incl. battery) 0,07kg
Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 21 10.03.11 08:59