LEGRAND HD4657M3 User manual

1
1
2
3
HD4657M3
HD4657M4
HC4657M3
HC4657M4
HS4657M3
HS4657M4
573912
573913
front view
rear view
Technical data
Power supply via SCS BUS: 27 Vdc
Operating power supply with SCS BUS: 18 – 27 Vdc
Maximum current draw HD/HC/HS4657M3: 20 mA
Maximum current draw HD/HC/HS4657M4: 25 mA
Maximum current draw 573912/13: 35 mA
Operating temperature: 0–40°C
Description
The touch control is a device in which conventional buttons are replaced by capacitive
sensors.The device can then carry out some typical functions of a SCS control when you
simply touch its surface. It is available in ush-mounted versions with 3 or 4 modules,
with respectively 6 and 8 buttons. Each zone corresponding to a button is marked in
the centre by a light-blue LED. When the user brings a nger near to it, the brightness
increases signicantly and remains bright until the nger is moved away. YOU can
change the level of brightness of the LEDs with the adjustment button. The control can
operate in four dierent modes: self-learning, scenarios, rocker, CEN.
- The self-learning mode (cyclic or non-cyclic) allows you to pair each button with
most of the typical controls of automation, sound and video door entry systems (stair
lights, door openers, oor calls, lock and camera cycling), as well as the auxiliary
controls. Available only with the physical conguration. With MYHOME_Suite virtual
conguration you can associate each button with a specic function.
- Scenario mode: allows you to recall, program and delete 6 or 8 scenarios of a scenario
module.
- Rocker mode: enables piloting 3 or 4 consecutive lighting points or roller shutters (or
rooms or groups).
- Scenario programmer mode: allows you to use the control with the scenario
programmer MH200N.
To enable cleaning the device you can temporarily disable the sensitive areas by pressing
two end zones diagonally. The LEDs will start ashing in sequence and normal operation
will be returned after 10 seconds have elapsed without any further pressing.
Legend
1. Button for programming and setting LED brightness
2. Congurator socket
3. BUS
Touch control
MQ00110-f-EN 07/06/2014
The device can be configured in two ways:
- PHYSICAL CONFIGURATION, inserting the configurators in position.
- Configuration via MYHOME_Suite software package, downloadable from
www.homesystems-legrandgroup.com; this mode has the advantage of offering many
more options than the physical configuration.
For a list of the procedures and their meanings, please refer to the instructions in
this sheet and to the "Function Descriptions" help section in the
MYHOME_Suite software package.
Configuration
List of Functions
The device performs the following functions:
1. LIGHT SWITCH
2. AUTOMATION CONTROL
3. DEVICE LOCKING/UNLOCKING
4. SCENARIO MODULE CONTROL
5. PROGRAMMED SCENARIO ACTIVATION
6. PLUS PROGRAMMED SCENARIO ACTIVATION
7. VIDEO DOOR ENTRY FUNCTIONS
8. SOUND SYSTEM CONTROL
Aroom
PL lighting point
Mmode
SET LED display mode
Button 1
Button 2
Button 3
Button 4
Button 5
Button 6
Button 7
Button 8

2
HD4657M3
HD4657M4
HC4657M3
HC4657M4
HS4657M3
HS4657M4
573912
573913
Touch control
MQ00110-f-EN 07/06/2014
1.1 Addressing
Address type Virtual configuration (MYHOME_Suite) Physical configuration
Point-to-point Room 0-10 A=1-9
Lighting point 0-15 PL=0-9
Room 0-10 A=AMB
Group 1-255 A=GR
General general A=GEN
Function selection
1. Self-learning mode
NOTE: With the virtual configuration, for the room, group and general controls, you can set a light
point address for the return of the load status
This mode is available only with the physical configuration. With MYHOME_Suite virtual
conguration you need to associate each button with the specic function.
For both modes,
you will have to configure the addresses of the device.
1.2 Configuration
Virtual configuration (MYHOME_Suite) Physical configuration
Function Parameter / setting
Associating the buttons on the touch control with the single
commands performed by the control devices and/or actuators - 1) M=0
Cyclic self-learning:
This mode is a variant of the self-learning mode (M=0), in
which, however, the buttons never work cyclically. So if, for
example, ON is learned for an actuator or dimmer, the pair of
buttons is automatically configured to turn on or increase the
level of brightness for the top button, turn off or decrease the
level of brightness for the bottom one. Whereas, if a single
function is learned (e.g. calling up a scenario), the other button
of the pair will remain without any function or keep the function
it had previously.The device can be configured either with any
A/PL address already in the system or with a unique address not
used by other devices.
- 1) M=6
NOTE 1: MYHOME_Suite allows you for each button to define all the operating modes for the
functions: light switch, automation control, scenario module control, programmed scenarios, PLUS
Lighting Management scenario, PLUS programmed scenario, sound system and video door entry
functions.
Installation and destination level:
The special control can also be used in systems where there are SCS/SCS interfaces (F422).
By installing the control on the BUS of an interface (installation level), you can control one
or more actuators located on the BUS of another interface (destination level).
Function Virtual configuration (MYHOME_Suite) Physical configuration
Destination level Local bus 1-15 I= 1-9
Riser bus riser I=CEN
Complete system entire system I=0
To configure the installation level use MYHOME_Suite virtual configuration.

3
HD4657M3
HD4657M4
HC4657M3
HC4657M4
HS4657M3
HS4657M4
573912
573913
Touch control
MQ00110-f-EN 07/06/2014
3. Scenario module control
3.1 Addressing
Function Virtual configuration (MYHOME_Suite) Physical configuration
Room (of the scenario module) 0-10 A=1-9
Lighting point (of the scenario module) 0-15 PL=0-9
2. Device locking/unlocking
To configure use MYHOME_Suite virtual configuration
NOTE: Use only the screwdriver supplied to operate the P button for programming and LED
brightness adjustment.
1.3 Programming the buttons
To associate each button with a dierent command, the procedure is as follows:
1) Briey press the button on the back, the LEDs will light up in rotation;
2) Within 20 seconds, touch the button you want to program: the LED will start
ashing, indicating activation of the programming mode;
3) Set the command you want to assign to the button, using the controls and/or the
corresponding actuator, the LEDs will start to rotate;
4) You can now repeat steps 2 and 3 for all the buttons, including any button that you
have already assigned in case you want to change it;
5) Briey press the programming button or wait 20 seconds to exit programming.
Deleting button programming
1) Briey press the button on the back, the LEDs will light up in rotation;
2) Within 20 seconds, press the button you want to delete and hold it for 4 seconds;
from this moment onwards the deleted button will no longer activate any command
until it is reprogrammed;
3) The corresponding LED will blink for 4 seconds alternately with the others, after
which you can repeat step 2 to delete other programming;
4) Briey press the button or wait 20 seconds to exit deletion.
NOTE: To delete the programming for all the buttons simultaneously, briey press the
button on the back, the LEDs will light up in rotation; press again and hold down the
button on the back for 10 seconds: the LEDs will blink for approximately 4 seconds, thus
conrming deletion of all the programming.
This operating mode is only used if the system has a scenario module F420, the
combination is made by assigning the same address to both items. The user can create,
delete or modify the scenarios contained in the scenario module and is able to call them
up using the buttons.The procedure allows you to save up to 16 scenarios using two
devices with 8 buttons, or three devices with 6 buttons.
To configure the "Installation level" and the "Destination level" and f or Button activation
delays use MYHOME_Suite virtual configuration

4
HD4657M3
HD4657M4
HC4657M3
HC4657M4
HS4657M3
HS4657M4
573912
573913
button
deleting scenarios
reset LED
scenarios/learning
programming
locking/unlocking
button
programming
status LED
NOTE 1: Match between the number of the scenario stored in the scenario module and the control buttons in the possible congurations:
3-module control (6 scenarios)
Button number M=1 M=4 M=3
Button 1 Scenario 1 Scenario 7 Scenario 13
Button 2 Scenario 2 Scenario 8 Scenario 14
Button 3 Scenario 3 Scenario 9 Scenario 15
Button 4 Scenario 4 Scenario 10 Scenario 16
Button 5 Scenario 5 Scenario 11
Button 6 Scenario 6 Scenario 12
4-module control (8 scenarios)
Button number M=1 M=2
Button 1 Scenario 1 Scenario 9
Button 2 Scenario 2 Scenario 10
Button 3 Scenario 3 Scenario 11
Button 4 Scenario 4 Scenario 12
Button 5 Scenario 5 Scenario 13
Button 6 Scenario 6 Scenario 14
Button 7 Scenario 7 Scenario 15
Button 8 Scenario 8 Scenario 16
F420
Touch control
MQ00110-f-EN 07/06/2014
Virtual configuration (MYHOME_Suite) Physical configuration
Function Parameter / setting
Modifying and activating a scenario, Scenario button 1-16 M=1-4 1)
3.2 Mode
Deleting a scenario
1) The F420 scenario module must be congured with self-learning enabled;
2) Briey press the button on the back, the LEDs will light up in rotation;
3) Within 20 seconds, press the button corresponding to the scenario that you want to
delete and hold it for 4 seconds;
4) The deleted device button LEDs will blink for 4 seconds, after which you can repeat
step 2 to delete other programming.
5) Briey press the button or wait 20 seconds to exit deletion.
NOTE: To reset the entire memory you need to act directly on the scenario module:
hold down the "DEL" button for 10 seconds after enabling the scenario module for
programming.
Programming a scenario
To program the scenario, the procedure is as follows:
1) The F420 scenario module must be congured with self-learning enabled (you need
to press the self-learning button so that the corresponding LED is green, self-learning
is not enabled if it is red);
2) Briey press the button on the back, the LEDs for the buttons enabled for the scenario
with programming function will blink 1 sec. ON and 1 sec. OFF;
3) Touch the button corresponding to the scenario to be programmed: the LED will begin
to ash (on receiving the update of the scenario module) indicating activation of the
programming mode;
4) Set the scenario using the controls and/or the corresponding actuators;
5) Touch the button to exit programming: the LEDs will start ashing in rotation and you
can now repeat steps 2, 3 and 4 for all the scenarios, including any button that you
have already assigned in case you want to change it;
6) Briey press the button or wait 20 seconds to exit programming.

5
HD4657M3
HD4657M4
HC4657M3
HC4657M4
HS4657M3
HS4657M4
573912
573913
4. Programmed scenario activation
Virtual configuration (MYHOME_Suite) Physical configuration
Addressing type Room 0-10 1-9
Lighting point 0-15 1-9
Enabling buttons for sending a command to the scenario programmer MH200N.
The address of the assigned command in positions A and PL must be different to the
addresses assigned to the actuators. The control can be connected at any point in the
system (local bus or riser).
4.1 Addressing
Virtual configuration (MYHOME_Suite) Physical configuration
Button 1) 0-31 M=CEN
4.2 Mode
5. Plus Light Management scenario activation
To configure use MYHOME_Suite virtual configuration.
6. Plus programmed scenario activation
To configure the number 1 - 2047 of the scenario and of the buttons 0 - 31 on the
control device, use MYHOME_Suite virtual configuration.
7. Video door entry functions
To configure the Address for the external unit of the level use MYHOME_Suite virtual
configuration.
7.2 Stair lights switch
To configure use MYHOME_Suite virtual configuration.
Touch control
MQ00110-f-EN 07/06/2014
The association between a scenario configured in the programmer MH200N and the rela-
ted touch control activation buttons (identified with 1-6 or 1-8 with physical configura-
tion and 0-31 with MYHOME_Suite) is made when programming the device MH200N.
7.3 Floor call control
To configure use MYHOME_Suite virtual configuration.
7.1 Unlocking control
To configure the Address for the external unit of the level use MYHOME_Suite virtual
configuration.
8. Sound system control
To configure use MYHOME_Suite virtual configuration.

6
DEFAULT
0%
40%
25%
HD4657M3
HD4657M4
HC4657M3
HC4657M4
HS4657M3
HS4657M4
573912
573913
Selecting LED brightness
With the physical conguration, you can adjust the brightness of the
LEDs by holding down (t>2s) the button on the back. The button works
on 3 levels of brightness: from a default value (25%) the brightness
varies every 2 seconds showing the 3 settable levels, as shown in the following
drawing. To select the desired level simply release the button. With the virtual
conguration you can adjust the brightness of the LEDs on 10 dierent levels.
If you have chosen to illuminate the buttons when they are pressed (status return), the
brightness level depends on the setting of the LEDs, as indicated below:
Touch control
MQ00110-f-EN 07/06/2014
Virtual configuration (MYHOME_Suite) Physical configuration
Function Parameter / setting LED brightness level Fade brightness
LED brightness
LED fade
1-10 25 % 65 %
40 % 70 %
0 % 20 %
NOTE: There could be a difference in brightness and colour from one device to another (even in
the same production batch) due to the construction technology.

7
HD4657M3
HD4657M4
HC4657M3
HC4657M4
HS4657M3
HS4657M4
573912
573913
After installing the device wait two minutes for auto-calibration to end.
During this time, commands may be automatically sent to the system.
!
Congurator in SET position Behaviour
0• LED ON even if button not congured
• No status return
• Fade eect on
1• LED ON even if button not congured
• No status return
• Fade eect o
2• LED ON only if congured (not congured -> LED OFF)
• No status return
• Fade eect on
3• LED ON only if congured (not congured -> LED OFF)
• No status return
• Fade eect o
4• LED ON even if button not congured
• Status return on
• Fade eect on
5• LED ON even if button not congured
• Status return on
• Fade eect o
6• LED ON only if congured (not congured -> LED OFF)
• Status return on
• Fade eect on
7• LED ON only if congured (not congured -> LED OFF)
• Status return on
• Fade eect o
Selecting the LED display mode
You can choose:
- whether at rest to keep the LEDs that are not used/congured o or on;
- whether to illuminate the LEDs or not when you press the corresponding button
(status return); to obtain an optimal status return eect it is recommended to set a
low LED brightness level.
- whether or not to give the illuminating buttons a "fade" eect.
Touch control
MQ00110-f-EN 07/06/2014
Virtual configuration (MYHOME_Suite) Physical configuration
Function Parameter / setting
Feedback update YES, NO SET=0-7 1)
NOTE 1: To choose the configurator, see the following table: