LEGRAND radiant WWP20CCV2 User manual
Smart Plug-In Dimmer, Wi-Fi
before you start
Review this guide in its entirety. Consult an electrician with any questions or if
you are unsure of your abilities.
Caution: To reduce the risk of injury and/or overheating and damage to
other equipment:
• For dry, indoor use only.
• Connect the Smart Plug-In Dimmer to a 120 VAC, 60 Hz power
source ONLY.
• This Smart Plug-In Dimmer is intended for lamps with dimmable
bulbs ONLY.
• To reduce the risk of electrical shock, this equipment has a grounding
type plug that has a third (grounding) pin. If the plug does not fit in
outlet, contact a qualified electrician to install the proper outlet.
Visit www.legrand.us/radiant/smart-lighting/support for support.
installation & setup
1|plug in the smart plug-in dimmer
Insert the lamp or device to be controlled into the outlet on the Smart
Plug-In Dimmer.
The Smart Dimmer up/down buttons can be reversed for use in outlets with the
ground plug up:
• Hold the bottom button while plugging in your dimmer. The dimmer
automatically adjusts the orientation.
2|test the smart plug-in dimmer
aWith the lamp or device on, press the top button on the Smart Plug-In
Dimmer to turn your device on.
bHold the bottom button to decrease the light level.
cHold the top button to increase the light level.
dPress the bottom button to turn your device off.
TROUBLESHOOTING TIP:
If the device is not responding to the dimmer, confirm that the outlet is
powered and that the device is functional.
getting to know your plug-in
Item Name Description
1 Top Button
• Press to turn the light on or double-tap to
raise the dimming percentage to 100%.
• Press and hold any button to quickly change
the dimming percentage by 20% per second.
2 Bottom Button • Press to turn the device off.
3 LED Locator Light • Indicates the current state of the device. Refer
to “LED Locator Light Explanations” for detail.
4 Outlet • Plug your dimmable device into the socket.
specifications
Load Rating
Incandescent/halogen 300 W
CFL/LED 100 W
Legrand reserves the right to change specifications without notice.
NOTE: The dimmer ships in forward phase mode to accommodate most load
types. For loads that require reverse phase dimming, such as ELV loads, adjust
the phase using the app.
SCAN TO WATCH THE
INSTALLATION VIDEO
3|set up your system
aDownload and launch the Smart Lights, Wi-Fi app by Legrand. The app is
available on the App Store or on Google Play.
bConnect your Smart Plug-In Dimmer to your home network by following the
step by step instructions in the app.
cUse the app to control your Smart Plug-In Dimmer.
Google Play and the Google Play logo are trademarks of Google LLC.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
SCAN TO WATCH HOW
TO SET UP THE APP
SCAN TO DOWNLOAD
RESET TO FACTORY DEFAULT
You can delete the device from the
app to reset or while device is off
press and hold dim button for 10
seconds then release.
NOTE: When it is turned on, the Smart
Dimmer recalls the most recent
dimming level.
1
2
3
4
LED LOCATOR LIGHT EXPLANATIONS
LED
Color State of Light Explanation
Blinking
Amber Factory default; ready to connect to your network.
Solid White Device is connected to your network.
Smart Plug-In Dimmer, Wi-Fi
before you start
Review this guide in its entirety. Consult an electrician with any questions or if
you are unsure of your abilities.
Caution: To reduce the risk of injury and/or overheating and damage to
other equipment:
• For dry, indoor use only.
• Connect the Smart Plug-In Dimmer to a 120 VAC, 60 Hz power
source ONLY.
• This Smart Plug-In Dimmer is intended for lamps with dimmable
bulbs ONLY.
• To reduce the risk of electrical shock, this equipment has a grounding
type plug that has a third (grounding) pin. If the plug does not fit in
outlet, contact a qualified electrician to install the proper outlet.
Visit www.legrand.us/radiant/smart-lighting/support for support.
installation & setup
1|plug in the smart plug-in dimmer
Insert the lamp or device to be controlled into the outlet on the Smart
Plug-In Dimmer.
The Smart Dimmer up/down buttons can be reversed for use in outlets with the
ground plug up:
• Hold the bottom button while plugging in your dimmer. The dimmer
automatically adjusts the orientation.
2|test the smart plug-in dimmer
aWith the lamp or device on, press the top button on the Smart Plug-In
Dimmer to turn your device on.
bHold the bottom button to decrease the light level.
cHold the top button to increase the light level.
dPress the bottom button to turn your device off.
TROUBLESHOOTING TIP:
If the device is not responding to the dimmer, confirm that the outlet is
powered and that the device is functional.
getting to know your plug-in
Item Name Description
1 Top Button
• Press to turn the light on or double-tap to
raise the dimming percentage to 100%.
• Press and hold any button to quickly change
the dimming percentage by 20% per second.
2 Bottom Button • Press to turn the device off.
3 LED Locator Light • Indicates the current state of the device. Refer
to “LED Locator Light Explanations” for detail.
4 Outlet • Plug your dimmable device into the socket.
specifications
Load Rating
Incandescent/halogen 300 W
CFL/LED 100 W
Legrand reserves the right to change specifications without notice.
NOTE: The dimmer ships in forward phase mode to accommodate most load
types. For loads that require reverse phase dimming, such as ELV loads, adjust
the phase using the app.
SCAN TO WATCH THE
INSTALLATION VIDEO
3|set up your system
aDownload and launch the Smart Lights, Wi-Fi app by Legrand. The app is
available on the App Store or on Google Play.
bConnect your Smart Plug-In Dimmer to your home network by following the
step by step instructions in the app.
cUse the app to control your Smart Plug-In Dimmer.
Google Play and the Google Play logo are trademarks of Google LLC.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
SCAN TO WATCH HOW
TO SET UP THE APP
SCAN TO DOWNLOAD
RESET TO FACTORY DEFAULT
You can delete the device from the
app to reset or while device is off
press and hold dim button for 10
seconds then release.
NOTE: When it is turned on, the Smart
Dimmer recalls the most recent
dimming level.
1
2
3
4
LED LOCATOR LIGHT EXPLANATIONS
LED
Color State of Light Explanation
Blinking
Amber Factory default; ready to connect to your network.
Solid White Device is connected to your network.
Smart Plug-In Dimmer, Wi-Fi
before you start
Review this guide in its entirety. Consult an electrician with any questions or if
you are unsure of your abilities.
Caution: To reduce the risk of injury and/or overheating and damage to
other equipment:
• For dry, indoor use only.
• Connect the Smart Plug-In Dimmer to a 120 VAC, 60 Hz power
source ONLY.
• This Smart Plug-In Dimmer is intended for lamps with dimmable
bulbs ONLY.
• To reduce the risk of electrical shock, this equipment has a grounding
type plug that has a third (grounding) pin. If the plug does not fit in
outlet, contact a qualified electrician to install the proper outlet.
Visit www.legrand.us/radiant/smart-lighting/support for support.
installation & setup
1|plug in the smart plug-in dimmer
Insert the lamp or device to be controlled into the outlet on the Smart
Plug-In Dimmer.
The Smart Dimmer up/down buttons can be reversed for use in outlets with the
ground plug up:
• Hold the bottom button while plugging in your dimmer. The dimmer
automatically adjusts the orientation.
2|test the smart plug-in dimmer
aWith the lamp or device on, press the top button on the Smart Plug-In
Dimmer to turn your device on.
bHold the bottom button to decrease the light level.
cHold the top button to increase the light level.
dPress the bottom button to turn your device off.
TROUBLESHOOTING TIP:
If the device is not responding to the dimmer, confirm that the outlet is
powered and that the device is functional.
getting to know your plug-in
Item Name Description
1 Top Button
• Press to turn the light on or double-tap to
raise the dimming percentage to 100%.
• Press and hold any button to quickly change
the dimming percentage by 20% per second.
2 Bottom Button • Press to turn the device off.
3 LED Locator Light • Indicates the current state of the device. Refer
to “LED Locator Light Explanations” for detail.
4 Outlet • Plug your dimmable device into the socket.
specifications
Load Rating
Incandescent/halogen 300 W
CFL/LED 100 W
Legrand reserves the right to change specifications without notice.
NOTE: The dimmer ships in forward phase mode to accommodate most load
types. For loads that require reverse phase dimming, such as ELV loads, adjust
the phase using the app.
SCAN TO WATCH THE
INSTALLATION VIDEO
3|set up your system
aDownload and launch the Smart Lights, Wi-Fi app by Legrand. The app is
available on the App Store or on Google Play.
bConnect your Smart Plug-In Dimmer to your home network by following the
step by step instructions in the app.
cUse the app to control your Smart Plug-In Dimmer.
Google Play and the Google Play logo are trademarks of Google LLC.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
SCAN TO WATCH HOW
TO SET UP THE APP
SCAN TO DOWNLOAD
RESET TO FACTORY DEFAULT
You can delete the device from the
app to reset or while device is off
press and hold dim button for 10
seconds then release.
NOTE: When it is turned on, the Smart
Dimmer recalls the most recent
dimming level.
1
2
3
4
LED LOCATOR LIGHT EXPLANATIONS
LED
Color State of Light Explanation
Blinking
Amber Factory default; ready to connect to your network.
Solid White Device is connected to your network.
Smart Plug-In Dimmer, Wi-Fi
before you start
Review this guide in its entirety. Consult an electrician with any questions or if
you are unsure of your abilities.
Caution: To reduce the risk of injury and/or overheating and damage to
other equipment:
• For dry, indoor use only.
• Connect the Smart Plug-In Dimmer to a 120 VAC, 60 Hz power
source ONLY.
• This Smart Plug-In Dimmer is intended for lamps with dimmable
bulbs ONLY.
• To reduce the risk of electrical shock, this equipment has a grounding
type plug that has a third (grounding) pin. If the plug does not fit in
outlet, contact a qualified electrician to install the proper outlet.
Visit www.legrand.us/radiant/smart-lighting/support for support.
installation & setup
1|plug in the smart plug-in dimmer
Insert the lamp or device to be controlled into the outlet on the Smart
Plug-In Dimmer.
The Smart Dimmer up/down buttons can be reversed for use in outlets with the
ground plug up:
• Hold the bottom button while plugging in your dimmer. The dimmer
automatically adjusts the orientation.
2|test the smart plug-in dimmer
aWith the lamp or device on, press the top button on the Smart Plug-In
Dimmer to turn your device on.
bHold the bottom button to decrease the light level.
cHold the top button to increase the light level.
dPress the bottom button to turn your device off.
TROUBLESHOOTING TIP:
If the device is not responding to the dimmer, confirm that the outlet is
powered and that the device is functional.
getting to know your plug-in
Item Name Description
1 Top Button
• Press to turn the light on or double-tap to
raise the dimming percentage to 100%.
• Press and hold any button to quickly change
the dimming percentage by 20% per second.
2 Bottom Button • Press to turn the device off.
3 LED Locator Light • Indicates the current state of the device. Refer
to “LED Locator Light Explanations” for detail.
4 Outlet • Plug your dimmable device into the socket.
specifications
Load Rating
Incandescent/halogen 300 W
CFL/LED 100 W
Legrand reserves the right to change specifications without notice.
NOTE: The dimmer ships in forward phase mode to accommodate most load
types. For loads that require reverse phase dimming, such as ELV loads, adjust
the phase using the app.
SCAN TO WATCH THE
INSTALLATION VIDEO
3|set up your system
aDownload and launch the Smart Lights, Wi-Fi app by Legrand. The app is
available on the App Store or on Google Play.
bConnect your Smart Plug-In Dimmer to your home network by following the
step by step instructions in the app.
cUse the app to control your Smart Plug-In Dimmer.
Google Play and the Google Play logo are trademarks of Google LLC.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
SCAN TO WATCH HOW
TO SET UP THE APP
SCAN TO DOWNLOAD
RESET TO FACTORY DEFAULT
You can delete the device from the
app to reset or while device is off
press and hold dim button for 10
seconds then release.
NOTE: When it is turned on, the Smart
Dimmer recalls the most recent
dimming level.
1
2
3
4
LED LOCATOR LIGHT EXPLANATIONS
LED
Color State of Light Explanation
Blinking
Amber Factory default; ready to connect to your network.
Solid White Device is connected to your network.
Smart Plug-In Dimmer, Wi-Fi
before you start
Review this guide in its entirety. Consult an electrician with any questions or if
you are unsure of your abilities.
Caution: To reduce the risk of injury and/or overheating and damage to
other equipment:
• For dry, indoor use only.
• Connect the Smart Plug-In Dimmer to a 120 VAC, 60 Hz power
source ONLY.
• This Smart Plug-In Dimmer is intended for lamps with dimmable
bulbs ONLY.
• To reduce the risk of electrical shock, this equipment has a grounding
type plug that has a third (grounding) pin. If the plug does not fit in
outlet, contact a qualified electrician to install the proper outlet.
Visit www.legrand.us/radiant/smart-lighting/support for support.
installation & setup
1|plug in the smart plug-in dimmer
Insert the lamp or device to be controlled into the outlet on the Smart
Plug-In Dimmer.
The Smart Dimmer up/down buttons can be reversed for use in outlets with the
ground plug up:
• Hold the bottom button while plugging in your dimmer. The dimmer
automatically adjusts the orientation.
2|test the smart plug-in dimmer
aWith the lamp or device on, press the top button on the Smart Plug-In
Dimmer to turn your device on.
bHold the bottom button to decrease the light level.
cHold the top button to increase the light level.
dPress the bottom button to turn your device off.
TROUBLESHOOTING TIP:
If the device is not responding to the dimmer, confirm that the outlet is
powered and that the device is functional.
getting to know your plug-in
Item Name Description
1 Top Button
• Press to turn the light on or double-tap to
raise the dimming percentage to 100%.
• Press and hold any button to quickly change
the dimming percentage by 20% per second.
2 Bottom Button • Press to turn the device off.
3 LED Locator Light • Indicates the current state of the device. Refer
to “LED Locator Light Explanations” for detail.
4 Outlet • Plug your dimmable device into the socket.
specifications
Load Rating
Incandescent/halogen 300 W
CFL/LED 100 W
Legrand reserves the right to change specifications without notice.
NOTE: The dimmer ships in forward phase mode to accommodate most load
types. For loads that require reverse phase dimming, such as ELV loads, adjust
the phase using the app.
SCAN TO WATCH THE
INSTALLATION VIDEO
3|set up your system
aDownload and launch the Smart Lights, Wi-Fi app by Legrand. The app is
available on the App Store or on Google Play.
bConnect your Smart Plug-In Dimmer to your home network by following the
step by step instructions in the app.
cUse the app to control your Smart Plug-In Dimmer.
Google Play and the Google Play logo are trademarks of Google LLC.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
SCAN TO WATCH HOW
TO SET UP THE APP
SCAN TO DOWNLOAD
RESET TO FACTORY DEFAULT
You can delete the device from the
app to reset or while device is off
press and hold dim button for 10
seconds then release.
NOTE: When it is turned on, the Smart
Dimmer recalls the most recent
dimming level.
1
2
3
4
LED LOCATOR LIGHT EXPLANATIONS
LED
Color State of Light Explanation
Blinking
Amber Factory default; ready to connect to your network.
Solid White Device is connected to your network.
Smart Plug-In Dimmer, Wi-Fi
before you start
Review this guide in its entirety. Consult an electrician with any questions or if
you are unsure of your abilities.
Caution: To reduce the risk of injury and/or overheating and damage to
other equipment:
• For dry, indoor use only.
• Connect the Smart Plug-In Dimmer to a 120 VAC, 60 Hz power
source ONLY.
• This Smart Plug-In Dimmer is intended for lamps with dimmable
bulbs ONLY.
• To reduce the risk of electrical shock, this equipment has a grounding
type plug that has a third (grounding) pin. If the plug does not fit in
outlet, contact a qualified electrician to install the proper outlet.
Visit www.legrand.us/radiant/smart-lighting/support for support.
installation & setup
1|plug in the smart plug-in dimmer
Insert the lamp or device to be controlled into the outlet on the Smart
Plug-In Dimmer.
The Smart Dimmer up/down buttons can be reversed for use in outlets with the
ground plug up:
• Hold the bottom button while plugging in your dimmer. The dimmer
automatically adjusts the orientation.
2|test the smart plug-in dimmer
aWith the lamp or device on, press the top button on the Smart Plug-In
Dimmer to turn your device on.
bHold the bottom button to decrease the light level.
cHold the top button to increase the light level.
dPress the bottom button to turn your device off.
TROUBLESHOOTING TIP:
If the device is not responding to the dimmer, confirm that the outlet is
powered and that the device is functional.
getting to know your plug-in
Item Name Description
1 Top Button
• Press to turn the light on or double-tap to
raise the dimming percentage to 100%.
• Press and hold any button to quickly change
the dimming percentage by 20% per second.
2 Bottom Button • Press to turn the device off.
3 LED Locator Light • Indicates the current state of the device. Refer
to “LED Locator Light Explanations” for detail.
4 Outlet • Plug your dimmable device into the socket.
specifications
Load Rating
Incandescent/halogen 300 W
CFL/LED 100 W
Legrand reserves the right to change specifications without notice.
NOTE: The dimmer ships in forward phase mode to accommodate most load
types. For loads that require reverse phase dimming, such as ELV loads, adjust
the phase using the app.
SCAN TO WATCH THE
INSTALLATION VIDEO
3|set up your system
aDownload and launch the Smart Lights, Wi-Fi app by Legrand. The app is
available on the App Store or on Google Play.
bConnect your Smart Plug-In Dimmer to your home network by following the
step by step instructions in the app.
cUse the app to control your Smart Plug-In Dimmer.
Google Play and the Google Play logo are trademarks of Google LLC.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
SCAN TO WATCH HOW
TO SET UP THE APP
SCAN TO DOWNLOAD
RESET TO FACTORY DEFAULT
You can delete the device from the
app to reset or while device is off
press and hold dim button for 10
seconds then release.
NOTE: When it is turned on, the Smart
Dimmer recalls the most recent
dimming level.
1
2
3
4
LED LOCATOR LIGHT EXPLANATIONS
LED
Color State of Light Explanation
Blinking
Amber Factory default; ready to connect to your network.
Solid White Device is connected to your network.
Smart Plug-In Dimmer, Wi-Fi
before you start
Review this guide in its entirety. Consult an electrician with any questions or if
you are unsure of your abilities.
Caution: To reduce the risk of injury and/or overheating and damage to
other equipment:
• For dry, indoor use only.
• Connect the Smart Plug-In Dimmer to a 120 VAC, 60 Hz power
source ONLY.
• This Smart Plug-In Dimmer is intended for lamps with dimmable
bulbs ONLY.
• To reduce the risk of electrical shock, this equipment has a grounding
type plug that has a third (grounding) pin. If the plug does not fit in
outlet, contact a qualified electrician to install the proper outlet.
Visit www.legrand.us/radiant/smart-lighting/support for support.
installation & setup
1|plug in the smart plug-in dimmer
Insert the lamp or device to be controlled into the outlet on the Smart
Plug-In Dimmer.
The Smart Dimmer up/down buttons can be reversed for use in outlets with the
ground plug up:
• Hold the bottom button while plugging in your dimmer. The dimmer
automatically adjusts the orientation.
2|test the smart plug-in dimmer
aWith the lamp or device on, press the top button on the Smart Plug-In
Dimmer to turn your device on.
bHold the bottom button to decrease the light level.
cHold the top button to increase the light level.
dPress the bottom button to turn your device off.
TROUBLESHOOTING TIP:
If the device is not responding to the dimmer, confirm that the outlet is
powered and that the device is functional.
getting to know your plug-in
Item Name Description
1 Top Button
• Press to turn the light on or double-tap to
raise the dimming percentage to 100%.
• Press and hold any button to quickly change
the dimming percentage by 20% per second.
2 Bottom Button • Press to turn the device off.
3 LED Locator Light • Indicates the current state of the device. Refer
to “LED Locator Light Explanations” for detail.
4 Outlet • Plug your dimmable device into the socket.
specifications
Load Rating
Incandescent/halogen 300 W
CFL/LED 100 W
Legrand reserves the right to change specifications without notice.
NOTE: The dimmer ships in forward phase mode to accommodate most load
types. For loads that require reverse phase dimming, such as ELV loads, adjust
the phase using the app.
SCAN TO WATCH THE
INSTALLATION VIDEO
3|set up your system
aDownload and launch the Smart Lights, Wi-Fi app by Legrand. The app is
available on the App Store or on Google Play.
bConnect your Smart Plug-In Dimmer to your home network by following the
step by step instructions in the app.
cUse the app to control your Smart Plug-In Dimmer.
Google Play and the Google Play logo are trademarks of Google LLC.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
SCAN TO WATCH HOW
TO SET UP THE APP
SCAN TO DOWNLOAD
RESET TO FACTORY DEFAULT
You can delete the device from the
app to reset or while device is off
press and hold dim button for 10
seconds then release.
NOTE: When it is turned on, the Smart
Dimmer recalls the most recent
dimming level.
1
2
3
4
LED LOCATOR LIGHT EXPLANATIONS
LED
Color State of Light Explanation
Blinking
Amber Factory default; ready to connect to your network.
Solid White Device is connected to your network.
regulatory information
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the transmitter’s radiating structure(s)
and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved
by the manufacturer will void the warranty and the user’s authority to operate
the equipment.
FCC ID: A3LCWAM210S
IC NOTICE
This device complies with Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions: (1) this device may not
cause interference; and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT
This equipment meets the SAR evaluation limits given in RSS-102 Issue 5
requirements at the minimum separation distance of 15 mm to the human body.
Note: Any changes or modifications to this device that are not expressly approved
by the manufacturer, will void the warranty and the user’s authority to operate
the equipment.
IC ID: 649E-CWAM210S
warranty
This product is warranted under normal use against defects in workmanship
and materials for as long as you own it. If the product fails due to a
manufacturing defect during normal use, return it for a replacement at the
store where purchased or contact technical support at 1-877-833-3303.
A dated sales receipt must be provided for all replacement requests (legible
copies are acceptable).
Additional warranty details are available at http://www.legrand.us under your
device’s product page.
questions? we're here to help
PHONE: 1-877-833-3303
8:00 a.m. to 8:00 p.m. EST (M-F)
EMAIL: smartlighting@legrand.us
CHAT: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the icon to open a dialogue box)
WiFi®is a registered trademark of Wi-Fi Alliance®.
Legrand, North America
50 Boyd Avenue
Syracuse, NY 13209
1-877-833-3303
www.legrand.us
©2019 Legrand All Rights Reserved IS3034 07/19
regulatory information
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the transmitter’s radiating structure(s)
and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved
by the manufacturer will void the warranty and the user’s authority to operate
the equipment.
FCC ID: A3LCWAM210S
IC NOTICE
This device complies with Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions: (1) this device may not
cause interference; and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT
This equipment meets the SAR evaluation limits given in RSS-102 Issue 5
requirements at the minimum separation distance of 15 mm to the human body.
Note: Any changes or modifications to this device that are not expressly approved
by the manufacturer, will void the warranty and the user’s authority to operate
the equipment.
IC ID: 649E-CWAM210S
warranty
This product is warranted under normal use against defects in workmanship
and materials for as long as you own it. If the product fails due to a
manufacturing defect during normal use, return it for a replacement at the
store where purchased or contact technical support at 1-877-833-3303.
A dated sales receipt must be provided for all replacement requests (legible
copies are acceptable).
Additional warranty details are available at http://www.legrand.us under your
device’s product page.
questions? we're here to help
PHONE: 1-877-833-3303
8:00 a.m. to 8:00 p.m. EST (M-F)
EMAIL: smartlighting@legrand.us
CHAT: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the icon to open a dialogue box)
WiFi®is a registered trademark of Wi-Fi Alliance®.
Legrand, North America
50 Boyd Avenue
Syracuse, NY 13209
1-877-833-3303
www.legrand.us
©2019 Legrand All Rights Reserved IS3034 07/19
regulatory information
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the transmitter’s radiating structure(s)
and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved
by the manufacturer will void the warranty and the user’s authority to operate
the equipment.
FCC ID: A3LCWAM210S
IC NOTICE
This device complies with Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions: (1) this device may not
cause interference; and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT
This equipment meets the SAR evaluation limits given in RSS-102 Issue 5
requirements at the minimum separation distance of 15 mm to the human body.
Note: Any changes or modifications to this device that are not expressly approved
by the manufacturer, will void the warranty and the user’s authority to operate
the equipment.
IC ID: 649E-CWAM210S
warranty
This product is warranted under normal use against defects in workmanship
and materials for as long as you own it. If the product fails due to a
manufacturing defect during normal use, return it for a replacement at the
store where purchased or contact technical support at 1-877-833-3303.
A dated sales receipt must be provided for all replacement requests (legible
copies are acceptable).
Additional warranty details are available at http://www.legrand.us under your
device’s product page.
questions? we're here to help
PHONE: 1-877-833-3303
8:00 a.m. to 8:00 p.m. EST (M-F)
EMAIL: smartlighting@legrand.us
CHAT: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the icon to open a dialogue box)
WiFi®is a registered trademark of Wi-Fi Alliance®.
Legrand, North America
50 Boyd Avenue
Syracuse, NY 13209
1-877-833-3303
www.legrand.us
©2019 Legrand All Rights Reserved IS3034 07/19
regulatory information
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the transmitter’s radiating structure(s)
and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved
by the manufacturer will void the warranty and the user’s authority to operate
the equipment.
FCC ID: A3LCWAM210S
IC NOTICE
This device complies with Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions: (1) this device may not
cause interference; and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT
This equipment meets the SAR evaluation limits given in RSS-102 Issue 5
requirements at the minimum separation distance of 15 mm to the human body.
Note: Any changes or modifications to this device that are not expressly approved
by the manufacturer, will void the warranty and the user’s authority to operate
the equipment.
IC ID: 649E-CWAM210S
warranty
This product is warranted under normal use against defects in workmanship
and materials for as long as you own it. If the product fails due to a
manufacturing defect during normal use, return it for a replacement at the
store where purchased or contact technical support at 1-877-833-3303.
A dated sales receipt must be provided for all replacement requests (legible
copies are acceptable).
Additional warranty details are available at http://www.legrand.us under your
device’s product page.
questions? we're here to help
PHONE: 1-877-833-3303
8:00 a.m. to 8:00 p.m. EST (M-F)
EMAIL: smartlighting@legrand.us
CHAT: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the icon to open a dialogue box)
WiFi®is a registered trademark of Wi-Fi Alliance®.
Legrand, North America
50 Boyd Avenue
Syracuse, NY 13209
1-877-833-3303
www.legrand.us
©2019 Legrand All Rights Reserved IS3034 07/19
regulatory information
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the transmitter’s radiating structure(s)
and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved
by the manufacturer will void the warranty and the user’s authority to operate
the equipment.
FCC ID: A3LCWAM210S
IC NOTICE
This device complies with Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions: (1) this device may not
cause interference; and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT
This equipment meets the SAR evaluation limits given in RSS-102 Issue 5
requirements at the minimum separation distance of 15 mm to the human body.
Note: Any changes or modifications to this device that are not expressly approved
by the manufacturer, will void the warranty and the user’s authority to operate
the equipment.
IC ID: 649E-CWAM210S
warranty
This product is warranted under normal use against defects in workmanship
and materials for as long as you own it. If the product fails due to a
manufacturing defect during normal use, return it for a replacement at the
store where purchased or contact technical support at 1-877-833-3303.
A dated sales receipt must be provided for all replacement requests (legible
copies are acceptable).
Additional warranty details are available at http://www.legrand.us under your
device’s product page.
questions? we're here to help
PHONE: 1-877-833-3303
8:00 a.m. to 8:00 p.m. EST (M-F)
EMAIL: [email protected]
CHAT: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the icon to open a dialogue box)
WiFi®is a registered trademark of Wi-Fi Alliance®.
Legrand, North America
50 Boyd Avenue
Syracuse, NY 13209
1-877-833-3303
www.legrand.us
©2019 Legrand All Rights Reserved IS3034 07/19
Table of contents
Other LEGRAND Dimmer manuals
LEGRAND
LEGRAND MyHOME MHKIT4 Quick start guide
LEGRAND
LEGRAND MIRO MRP6 User manual
LEGRAND
LEGRAND 573866 User manual
LEGRAND
LEGRAND KNX modular dimmer Instruction Manual
LEGRAND
LEGRAND Pass & Seymour T600E Manual
LEGRAND
LEGRAND HKRL50 User manual
LEGRAND
LEGRAND adorne WNAL63 User manual
LEGRAND
LEGRAND WattStopper RH703PTU User manual
LEGRAND
LEGRAND 0 036 71 User manual
LEGRAND
LEGRAND HPM 700TM User manual
