Leica DISTO D2 User manual

Leica DISTOTM D2
The original laser distance meter

Overview 2
Technical data 3
Instrument Set-up 5
Operations 14
Message Codes 26
Care 27
Warranty 28
Safety instructions 29
Leica DISTO™ D2 1

Overview
Ove rview
The Leica DISTO™ is a laser distance meter oper-
ating with a class 2 laser. See chapter Technical
data for scope of use.
1Display
2ON/ Measure
3Add
4Functions
5Measuring reference
6Clear/ OFF
7Memory/ Timer
8Bluetooth® Smart
9Subtract
Leica DISTO™ D2 2

Technical data
Te c h n ica lda ta
Leica DISTO™ D2 3
General
Accuracy with favourable conditions * 1.5 mm / 1/16" ***
Accuracy with unfavourable conditions ** 3 mm / 1/8" ***
Range with favourable conditions * 0.05 - 100m / 0.16 - 330ft ***
Range with unfavourable conditions ** 0.05 - 60m / 0.16 - 200ft ***
Smallest unit displayed 0.1 mm / 1/32 in
X-Range Power Technology yes
Laser class 2
Laser type 635 nm, <1 mW
ø laser point | at distances 6 /30 /60 mm | 10/ 50/ 100 m
Protection class IP54 (dust- and splash water protected)
Auto. laser switch off after 90 s
Auto. power switch off after 180 s
Bluetooth® Smart Bluetooth® v4.0
Range of Bluetooth® Smart <10m
Battery durability (2 x AAA) up to 10000 measurements
Dimension (H x D x W) 116 x 44 x 26 mm | 4.57 x 1.73 x 1.02 in
Weight (with batteries) 100 g/ 3.53 oz
Temperature range Storage | Operation -25 to 70°C/ -13 to 158°F | -10 to 50°C/ 14 to 122°F
* favourable conditions are: white and diffuse reflecting target (white painted wall), low background illumination and moderate temperatures.
** unfavourable conditions are: targets with lower or higher reflectivity or high background illumination or temperatures at the upper or lower end of the specified temperature range.
*** Tolerances apply from 0.05 m to 5 m with a confidence level of 95%.
With favourable conditions the tolerance may deteriorate by 0.10 mm/m for distances above 5 m.
With unfavourable conditions the tolerance may deteriorate by 0.15 mm/m for distances above 5 m.

Technical data
Functions
Distance measuring yes
Min/Max measuring yes
Permanent measuring yes
Stake out yes
Addition/Subtraction yes
Area yes
Volume yes
Painter function (area with partial measurem.) yes
Pythagoras 2-point, 3-point
Memory 10 results
Beep yes
Illuminated display yes
Automatic multifunctional endpiece yes
Bluetooth® Smart yes
Leica DISTO™ D2 4

Instrument Set-up
Ins tru me n tSet-u p
Introduction
The safety instructions (see Safety
Instructions) and the user manual
should be read through carefully
before the product is used for the first
time.
The person responsible for the
product must ensure that all users
understand these directions and
adhere to them.
The symbols used have the following
meanings:
WARNING
Indicates a potentially hazardous situ-
ation or an unintended use which, if
not avoided, will result in death or ser-
ious injury.
CAUTION
Indicates a potentially hazardous situ-
ation or an unintended use which, if
not avoided, may result in minor injury
and/or appreciable material, financial
and environmental damage.
Important paragraphs which
must be adhered to in practice
as they enable the product to be
used in a technically correct and
efficient manner.
5
Leica DISTO™ D2

Instrument Set-up
Insert batteries
To ensure a reliable use, we recom-
mend using high quality Alkaline bat-
teries. Change batteries when
battery symbol is flashing.
Leica DISTO™ D2 6

Instrument Set-up
Switching ON/OFF
Device is turned OFF.
Leica DISTO™ D2 7

Instrument Set-up
Clear
Undo last action. Leave actual function, go to default
operation mode.
Leica DISTO™ D2 8

Instrument Set-up
Message Codes
If the message "i" appears with
a number, observe the instruc-
tions in Message Codes section.
Example:
Leica DISTO™ D2 9

Instrument Set-up
Adjusting measuring reference
Distance is measured from the front
of the device.
Press button 2 sec and ref-
erence from front is set per-
manently.
Distance is measured from the rear of
the device (standard setting).
Leica DISTO™ D2 10

Instrument Set-up
Multifunctional endpiece
The orientation of the endpiece
is automatically detected and
the zero point is adjusted accord-
ingly.
Leica DISTO™ D2 11

Instrument Set-up
Unit setting
Press both keys simultaneousley.
Switch between the following units:
0.000 m
0.00 ft
0.0000 m
0'00" 1/32
0.000 in
0 in 1/32
Leica DISTO™ D2 12

Instrument Set-up
Beep
Press both keys simultaneousley.
Leica DISTO™ D2 13

Operations
Ope rations
Measuring single distance
Aim active laser at target.
Target surfaces: Measuring
errors can occur when meas-
uring to colourless liquids, glass,
styrofoam or permeable sur-
faces or when aiming at high
gloss surfaces. Against dark
surfaces the measuring time
increases.
14
Leica DISTO™ D2

Operations
Permanent / Minimum-Maximum measuring
Used to measure room diagonals
(maximum values) or horizontal dis-
tance (minimum values). The min-
imum and maximum distance
measured is displayed (min, max.).
The last value measured is displayed
in the main line.
Stops permanent / minimum-max-
imum measuring.
Leica DISTO™ D2 15

Operations
Add / Subtract
The next measurement is added to
the previous one, respectively sub-
tracted from the previous one.
The result is shown in the main
line and the measured value
above. This process can be
repeated as required. The
same process can be used for
adding or subtracting areas or
volumes. In this case press
DIST to show the result.
Leica DISTO™ D2 16

Operations
Area
Aim laser at first target point. Aim laser at second target point.
The result is shown in the main
line and the measured value
above. Painter function: Press +
or - after starting the first meas-
urement. Measure and add or
subtract wall lengths. Measure
finally height for second length
to get the wall area.
Circumference is displayed.
Leica DISTO™ D2 17

Operations
Volume
Aim laser at first target point. Aim laser at second target point.
Aim laser at third target point. Circumference and wall area are dis-
played.
Leica DISTO™ D2 18

Operations
Memory (last 10 results)
Last 10 values are displayed. Navigates through last 10 values.
Leica DISTO™ D2 19