Lennox Hearth Products 290M User manual

TRIM KITS
MODEL VISTION™
INSTALLATION INSTRUCTIONS FOR INSTALLING TRIM
KITS FOR USE WITH VISION DIRECT-VENT GAS STOVES
775,290M
Rev. A, 10/2008
HEARTH PRODUCTS
KITS AND ACCESSORIES
DRAFT
10/27/2008
KIT CONTENTS
Please ensure that all these parts are included
1 ea. Louver Assembly
2 ea. Side Window Trim
1 ea. Front Window Trim
1 ea. Ash Lip Trim
2 ea. Allen Head Screws
4 ea. 10-24 Hex Nuts
4 ea. #10 Washers
1 ea. Instruction Sheet
TOOLS NEEDED:
5/32” Allen Wrench or T-Handle Wrench
1/8” Allen Wrench or T-Handle Wrench
3/8” Open End Wrench
INSTALLATION INSTRUCTIONS
Step 1. Remove the four screws from the top of the stove - Using a 1/8”
allen wrench remove the two button head screws on the back of
the stove (see Figure 1) and using a 5/32” allen wrench remove
the two socket head screws on the front of stove (see Figure 2).
Lift off the top of the stove. Retain the screws for reinstallation
of the stove top in Step 6.
Cat. No. Model Description
75276 VISN-TRIM-B-G Black Trim Kit / Gold Handle
75277 VISN-TRIM-B-N Black Trim Kit / Nickel Handle
75274 VISN-TRIM-G-G Gold Trim Kit / Gold Handle
75275 VISN-TRIM-N-N Brushed Nickel Trim Kit / Nickel Handle
Kits Include: Matching Trim for Glass, Louvers and Ash Lip
GENERAL INFORMATION
If you encounter any problems, need clarification of these instructions
or are not qualified to properly install this kit, contact you local distribu-
tor or dealer.
Read this instruction sheet in its entirety before beginning the installa-
tion.
All of these parts may scratch and bend, great care should be used
in handling them.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO
THESE INSTRUCTIONS.
TURN OFF THE STOVE AND ALLOW IT TO COMPLETELY COOL BEFORE
PROCEEDING.
CAUTION: Always ensure that plated surfaces are clean and free of
fingerprints before lighting stove. Fingerprints will leave permanent
blemishes if left on plated surface when lit. When installation is
complete, the trim should be gently cleaned with a soft cloth and
either alcohol or a household glass cleaner. Do not overtighten nuts,
overtightening can create visible dimples on the plated surface.
1
NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.
(Step 1) Using a 5/32” allen wrench, remove
the two socket head screws on the stove front.
(Step 3) Attach the louvers above the door with four supplied
screws (two on left side and two on right side of stove).
Stove Front
Stove Back
(Step1)Usinga 1/8”allenwrenchremovethe
two button head screws on the stove back.
Figure 1
Figure 2

2
Printed in U.S.A. © 2008 Lennox Hearth Products
P/N 775,290M REV. A 10/2008
NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.
Step 5. Using a 3/8” open end wrench, install the front door trim with
the four supplied nuts and washers. DO NOT OVERTIGHTEN THE
NUTS OR SCREWS. See Figure 5.
Step 3. Using a 5/32” allen wrench, attach the louvers above the door
with four supplied screws (two on left side and two on right side
of stove). See Figure 1 on Page 1.
Step 4. Slide the side window trim down into the brackets in the side wall
of the stove. It may be helpful to slightly pry open the brackets
on the stove to slide the side trim in. Be careful to not scratch the
glass or the trim. See Figure 4.
Step 6. Reattach the top of the stove with the four screws.
Step 7. To install the spring handle, first close the door and screw the
handleinto the receivingnut.Then spray a householdglass cleaner
or water on the shaft of the handle to act as a lubricant. Next,
twist the spring handle counterclockwise onto the shaft. Use a
household glass cleaner or alcohol and a soft cloth to remove
any fingerprints from all plated surfaces prior to firing the stove.
Read Caution on Page 1.
Figure 4
Figure 5
Lennox Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
1110 West Taft Avenue • Orange, CA 92865
Figure 6
COMPLETED
INSTALLATION
Front Door Trim
Step 2. Using a 5/32” allen wrench, attach the ash lip to the lower control
door using two supplied screws. See Figure 3.
Figure 3
5/32” Allen Wrench