Lennox Hearth Products LSS-CA35 User manual

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
GENERAL INFORMATION
CAST IRON FACADE
KITS
Step 1. Install the top and bottom grills to their corresponding top
and bottom cast iron facade pieces as detailed in the installation
instructions provided with the grillwork kits.
Step 2. Install five (kit-provided) facade holding screws to each of
the two side pieces ensuring compliance with the gaps shown in
Figure 1 .
Step 3. Hook the two cast iron side pieces onto the fireplace side
channelsasshownin Figure2 .Ifthefitistootightorloose,adjustthe
gap of the two holding screws. (See Figure 1 .)
Step 4. Insert set screws into the bottom corners of the arch. Set
screwsshouldbe flushwiththe frontofthe mountingbosses(refer to
Figure 4 ).
Thesecastironfacadekits aredesignedtobeusedinconjunctionwith
thegrillworkkits.Together,wheninstalled,thesekitscompletethefront
aspect of the Spectra LSS series gas fireplaces. The kits contain one
of each of the following cast iron facade pieces: bottom, top, left and
rightpiece.Theyalsocontainfour1/2inchlong1/4-20facadeholding
screws, six 1-1/2 inch long 1/4-20 facade holding screws and these
instructions.
INSTALLATION INSTRUCTIONS FOR CAST IRON FACADE KITS Model Numbers LSS-CA35 (H0378) and
LSS-CA40 (H0398) FOR USE WITH SPECTRA LSS SERIES GAS FIREPLACES
INSTALLATION INSTRUCTIONS
HEARTH PRODUCTS
KITS AND ACCESSORIES
750,164M
REV. A 12/2008
Figure 1
Figure 2
LENNOX HEARTH PRODUCTS
3/32 inch
(2.38 mm) 1-1/4 inch
(31.8 mm)
Screw Head to Facade Side Piece Gap
and Fastener Usage.
1/2 inch long,
1/4-20 Facade Holding Screws
1-1/2 inch long,
1/4-20 Facade
Holding Screws
(Three Places)
Cast Iron Side Piece
1/2 inch long Cast Iron Side Piece Holding Screws
1-1/2 inch long Cast Iron Bottom Piece Holding Screws
Cast iron side piece screw head
hooked behind top portion of shown
fireplace side channel detail
(top and bottom same method).
Side Piece
Note: The left cast iron side piece (shown above)
is sloped upward at the top, from left to right, to form a
mating fit to the arched cast iron top piece. The right cast
iron top piece has the opposite slope at the top.
Installing Cast Iron Side Pieces

NOTE:DIAGRAMS&ILLUSTRATIONSNOTTOSCALE.
Printed in U.S.A. © 2003 by Lennox Hearth Products
P/N 750,164M REV. A 12/2008
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
LENNOX HEARTH PRODUCTS
1110 West Taft Avenue • Orange, CA 92865
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Figure 3
Figure 5
Step 5. Slide the top cast iron piece (arched piece) as shown in
Figure 3 on to the two (2) holding screws protruding from the two
cast iron side pieces.
Installed Fireplace Cast Iron Facade and Grills
Top Cast Iron
(Arch) Piece
Bottom Cast
Iron Piece
Installing the Top and Bottom Cast Iron Pieces
Previouly
Installed
Cast Iron
Side Pieces
Bottom Cast Iron Piece
Detail Showing Installation
Orientation
TOP
Slot orientation
indicates facade top.
Figure 4
Step 6. Adjustment of the set screws on the bottom corners of the
archcanbeusedtotightenthefitbetweenthesides,thearchandthe
wall (see Figure 4 ). To adjust the set screw, it will be necessary to
removethetoparch. Makeadjustmentsinsmallincrementsuntilthe
desired fit has been achieved.
Step 7. Hook the bottom cast iron piece (with the top, up, as shown
in Figure 3 ) to the 4 holding screws protruding from the two cast
iron side pieces as shown in Figure 3 . See Figure 5 for the final
appearance of the installed cast iron facade.
See Detail A
Set Screw
Detail A