Lennox Hearth Products ADAGIO-AG User manual

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
HEARTH PRODUCTS
KITS AND ACCESSORIES
750,231M
REV. NC 06/2008
INSTALLATION INSTRUCTIONS FOR FACADE KITS
FOR USE WITH ADAGIO™ DIRECT-VENT GAS FIREPLACES
TM
KIT CONTENTS:
Facade Kit
1 ea. Facade Assembly (1)
1 ea. Instruction Sheet
INSTALL ONLY WHEN FIREPLACE IS OFF AND COOL.
ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS PROVIDED
IN THE INSTALLATION INSTRUCTIONS MANUAL AND THE CARE
ANDOPERATIONMANUALPROVIDEDWITHTHEAPPLIANCEAPPLY
TO THESE INSTRUCTIONS. THOROUGHLY READ AND FOLLOW
THE INSTRUCTIONS PROVIDED WITH THE APPLIANCE BEFORE
PROCEEDING TO THE FOLLOWING INSTRUCTIONS.
INSTALLATION INSTRUCTIONS
1. Install the appliance, firebox liner and logs per the Installation Instruc-
tions Manual provided with the appliance and the Installation Instruction
Sheet provided with the firebox liner kit (sold separately).
2. Using a 3/8” socket or nutdriver, remove heat shield, screen retainer and
screen from facade. See Figure 2.
Cat. No Model Description
H5773 ADAGIO-AG Arched Face Black Facade
H5774 ADAGIO-PF Arched Face Brushed Nickel Facade
1
The arched facade kits require a filigree inset kit. These kits are sold
separately. Contact your dealer for ordering information.
Filigree Inset Kits (Sold Separately - Required)
Cat. No. Model Description
H6845 ADAGIO-INSET-ASPEN-BK Aspen, Black
H6846 ADAGIO-INSET-ASPEN-BN Aspen, Brushed Nickel
H6847 ADAGIO-INSET-ASPEN-BKN Aspen, Black Nickel
H6848 ADAGIO-INSET-ASPEN-G Aspen, Gold
H6849 ADAGIO-INSET-NAPA-BK Napa, Black
H6850 ADAGIO-INSET-NAPA-BN Napa, Brushed Nickel
H6851 ADAGIO-INSET-NAPA-BKN Napa, Black Nickel
H6852 ADAGIO-INSET-NAPA-G Napa, Gold
H6853 ADAGIO-INSET-TUSCAN-BK Tuscan, Black
H6854 ADAGIO-INSET-TUSCAN-BN Tuscan, Brushed Nickel
H6855 ADAGIO-INSET-TUSCAN-BKN Tuscan, Black Nickel
H6856 ADAGIO-INSET-TUSCAN-G Tuscan, Gold
Filigree Inset Kit
1 ea. Upper Filigree inset (2)
1 ea. Lower Filigree inset (3)
7 ea. Washers #10 (4)
7 ea. Hex Head Nuts (5)
Installer: Leave This Instruction Sheet With The Appliance.
Consumer: Retain This Instruction Sheet For Future Reference.
Figure 1
TOOLS / SUPPLIES NEEDED:
3/8” Socket or Nutdriver
GENERAL INFORMATION
The arched facade kits are offered in two attractive finishes, black and
brushed nickel. If you encounter any problems or need clarification of
these instructions, contact you local distributor or dealer.
Note: The base of the appliance will need to be elevated by 3/4" minimum
above the floor to allow for the proper fit of the facade (i.e. 3/4" board as
platform). See Installation Instructions Manual.
FPO
47 Places
7 Places
5
2
3
1

2
5. Install the facade onto the fireplace face per instructions in Figure 3.
6. See Figure 4 for instructions on accessing the control compart-
ment.
To access the control compartment, pull the hinged door
forward and up as shown. To close, hinge the door closed
until magnets secure it in place.
Figure 4 - Opening the Control Compartment Panel
Figure 5 - Completed Installation
IMPORTANT NOTE (Gold and Nickel Finishes Only): The gold
and nickel finishes will require heat to harden and cure (after
approximately 3 fires, the finish will be completely cured). Prior
to burning this appliance the gold and nickel surfaces should be
cleaned thoroughly with a good window cleaning solution and a
soft cloth. Do not use any metal polishes or abrasives to clean
the surfaces. Any oils or fingerprints left on the finish during the
curing process may become permanent blemishes.
Magnets
Control Compartment
Control Compartment Panel
Facade
3. Using a 3/8” socket or nutdriver, install the upper filigree inset, lower
filigree inset, screen and screen retainer with provided washers and
nuts as shown in Figure 2. Note: you will have four extra washers
and nuts.
4. Reinstall heat shield aligning the top corners of the heat shield with
the etch marks in the back of the facade for proper placement. Do not
over tighten nuts.
Figure 2
Brushed Nickel
Facade Shown
Figure 3 - Install Facade
Tabs on Bracket
Assemblies (2
places each side)
Slots on Fireplace
(2 places each side)
Facade
Align the tabs on the
bracket assemblies all
the way into the slots
on fireplace, then push
facade down to ensure
engagement.
Printed in U.S.A. © 2008 Lennox Hearth Products
P/N 750,231M REV. NC 06/2008
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and the discontinuance of colors, styles and products.
Consult your local distributor for fireplace / insert code information.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Lennox Hearth Products
1110 West Taft Avenue • Orange, CA 92865
Note: There are two mount-
ing positions on the facade
hanging brackets to better
accommodate a range of
facing thicknesses. Adjust
to the notch on the hanging
bracket that works best for
your installation.
Heat Shield
Upper Filigree
Lower Filigree
Screen
Screen Retainer
Etch
Marks