Lennox Hearth Products Elite Series User manual

3-PIECE LOUVER ASSEMBLY KITS
GENERAL INFORMATION
These louver assembly kits may be used with Merit™, Merit Plus™or
Elite®series gas fireplaces. Kit applications are shown in Table 1.
KIT CONTENTS:
1 ea. Top louver assembly panel
1 ea. Bottom louver assembly panel
1 ea. Nameplate logo -
not used on short panel of EDVPF, EDVCR, EDVCL, EDPF(-2), EDCR(-2) & EDCL(-2)
1 ea. Installation Instructions
INSTALLATION INSTRUCTIONS FOR LOUVER ASSEMBLY KITS FOR USE
WITH MERIT™, MERIT PLUS™, OR ELITE®SERIES GAS FIREPLACES
INSTALLATION INSTRUCTIONS
Note: Do not operate fireplace without the eyebrow installed in its normal
position. See Figure 2 for models with louvers or Figure 3 for models
with radiant panels.
750,119M
Rev. B 03/2008
Hood must be installed asshown.
Hood must be installed as shown.
Top of Appliance
Top of Appliance
Louver Assembly
Top Radiant Panel
Top of Door Frame
Top of Door Frame
Figure 3 - Clean Face
Figure 1 - Louver Kit Contents
LOUVER SET KITS
Polished Brass Brushed Stainless Painted
Cat. # Model Cat. # Model Models Where Used
88L27 LVR24PB-2 88L31 LVR24BS 88L23 LVR24C-2 EDVPF, EDPF(-2), EDVCR, EDCR(-2), EDVCL, EDCL(-2), EBVPF, EBPF(-2), EBVCR, EBCR(-2), EBVCL,
EBCL(-2), EBBAY
88L28 LVR35PB-2 88L32 LVR35BS EDV3530, ED3530, MPD3530, MPD35ST, MPD35PF, MPB35ST
88L29 LVR40PB-2 88L33 LVR40BS 88L25 LVR40C-2 EDV4035, MPD4035, EDVST, EDVPF, EDVCR, EDVCL, EBVST, EBVPF, EBVCR, EBST, EBPF, EBBAY,
EBCL, EBCR
88L30 LVR45PB-2 88L34 LVR45BS EDV4540, ED4540-2, MPD4540
26M45 LVR33MPB 26M46 LVR33MBS MDR3328, MDT3328, MPDT3328, MPDR3328
H7024 LVR22PB H7025 LVR22BS MPD35PF
Table 1
Figure 2 - Louvered Face
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Lennox
Nameplate
Top Louver
Bottom Louver
LENNOX HEARTH PRODUCTS
KITS AND ACCESSORIES

Printed in U.S.A. © 2001 LENNOX HEARTH PRODUCTS
P/N 750,119M REV. B 03/2008
Merit, Merit Plus or Elite Gas Fireplaces -
Converting louvered fireplace to louvered or clean face to louvered-
Step 1. Remove the protective plastic covering from the louver assem-
blies.
Step 2. Grasp the existing top radiant panel / hood assembly or louver as-
semby and slightly lift and pull it forward away from the fireplace.
See Figure 3 for radiant panel assembly and Figure 2 for Louvered
assembly.
Step 3.Hang the replacement top louver assembly in the opening.
Step 4.Slide the existing hood into the slots on the lower edge of the cabinet
top flange. See Figure 2.
Step 5.
Open the bottom radiant panel or louver assembly by pushing in
simultaneously the left and right sides of the panel or assembly.
(The radiant panel or assembly is hinged at the bottom).
Step 6. Merit Models - Remove the assembly from the fireplace by removing
the hinge screw and spacer at each end.
Merit Plus or ELite Models - Remove the bottom radiant panel or
louver assembly from the fireplace by sliding the hinge pin, located
at the radiant panel’s left side, to the right until it disengages from
the left corner post hole. Pull the door diagonally to the left, away
from the fireplace. Note: Reverse the use of the words “left” and
“right” for EDCR models.
CAUTION
INSTALL ONLY WHEN THE FIREPLACE IS OFF AND COLD!
IMPORTANT NOTE
(Polished Brass & Brushed Stainless Kits Only): The finish on
the polished brass and brushed stainless louvers will require
heat to harden and cure (after approximately 3 fires, the finish
will be completely cured). Prior to burning this appliance, the
polishedbrassandbrushedstainlesssurfacesshouldbecleaned
thoroughly with a good window cleaning solution and a soft
cloth. Do not use any metal polishes or abrasives to clean the
surfaces. Any oils or fingerprints left on the finish during the
curing process may become permanent blemishes.
Step 7. Snap the replacement nameplate logo into the 2 holes provided in
the replacement louver assembly. Note: This is not applicable to
the short panel of the EDPF, EDCR, EDCL models.
Step 8. Merit Models - Install the replacement bottom louver assembly
using the existing hinge screws and spacers.
Merit Plus or ELite Models - Install the replacement bottom louver
assemblybyinsertingthe right sidelocatingpin into theright cabinet
corner post and then the left side spring-loaded pin into the left
cabinet corner post. Note: Reverse the use of the words “left” and
“right” for EDCR models.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design,
materials, specifications, prices and the discontinuance of colors, styles and products.
Consult your local distributor for fireplace code information.
1110 West Taft Avenue • Orange, CA 92865