Lennox Hearth Products RAVELLE 30 User manual

SCREEN FACE KIT
MODEL RAVELLE™ 30
INSTALLATION INSTRUCTIONS FOR INSTALLING SCREEN
FACE KIT FOR USE WITH THE RAVELLE™ 30 GAS FIREPLACE
775,288M
Rev. A, 10/2008
HEARTH PRODUCTS
KITS AND ACCESSORIES
DRAFT
10/27/2008
KIT CONTENTS (See Figure 1):
Please ensure that all these parts are included
1 ea. Screen Face [Complete] (A)
2 ea. Upper Brackets w/Screws (B)
2 ea. 1/4”-20 Lower Face Mounting Screws (C)
6 ea. #10 Washers
6 ea. 10-24 Hex Nuts
1 ea. Instruction Sheet
Cat. No. Model Description
75382 SCREENF-30 Screen Face, Double Door, Black
A
Right bracket to left
side of fireplace.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE 1
GENERAL INFORMATION
If you encounter any problems, need clarification of these instructions
or are not qualified to properly install this kit, contact you local distribu-
tor or dealer.
Read this instruction sheet in its entirety before beginning the installa-
tion.
All of these parts may scratch and bend, great care should be used
in handling them.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO
THESE INSTRUCTIONS.
TURN OFF THE FIREPLACE AND ALLOW IT TO COMPLETELY COOL
BEFORE PROCEEDING.
INSTALLATION INSTRUCTIONS
Step 1. Using a 5/32” allen wrench, remove the lower face mounting
brackets from the unit and reverse their locations left to right (see
Figure 2). Re-attach the brackets (see Figure 3)using the existing
10-24 screws. You will need to reverse the speed nuts so that the
flat side is toward the center of the fireplace. The outside dimension
between the brackets should be 28 inches.
Figure 1 - Kit Contents
Attach left bracket to
right side of fireplace.
TOOLS NEEDED:
Phillips Head Screwdriver
3/8” Socket or Nut Driver
5/32” Allen Wrench or T-Handle Wrench Figure 2
Left Bracket
CB
TM

Printed in U.S.A. © 2008 Lennox Hearth Products
P/N 775,288M REV. A 10/2008
Lennox reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local
distributor for fireplace code information.
Lennox Hearth Products
1110 West Taft Avenue • Orange, CA 92865
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
2
Attach left
bracket to right
side of fireplace
Figure 3
Step 2. Using a 3/8” socket or nut driver, attach the two upper mounting
brackets to the six studs (three on each side - indicated by arrows
in Figure 5)near the top, using the six #10 washers and 10-24 hex
nuts provided. The square notch should be to the bottom of the
face (see Figure 4).
Figure 4 - Upper Mounting Bracket
The square notch
should be to the
bottom of the face
Figure 5 - Install Upper Mounting Brackets
Step 3. Remove the screen doors from the face by gently lifting up and out
of their hinges. Check to make sure the washers that separate the
two halves of the hinge have not fallen off. Set the screen doors
aside.
Step 4. Using a phillips screwdriver (through upper grill opening) attach
the screen face to the fireplace starting with the upper brackets.
Screw the upper brackets in part way only, you will tighten them in
step 6.
Step 5. Open the lower door on the screen face and thread the two 1/4”-20
phillips head screws (provided) through the lower hinge mounts
into the speed nuts on lower face brackets, attached to the fireplace
(see Figure 6).
Step 6. Adjust the alignment and depth of the screen face until it sits flush
with the wall and tighten all four mounting screws.
Step 7. Finish the installation by putting the screen doors back on their
hinges (check to make sure the was hers are in place). This
completes the screen face Installation.
Figure 6 - Lower Hinge Mounts
Figure 7 - Completed Installation
1/4” Screw With Push Nut
(The push nut holds the screw in
place when installing face)