Lennox Hearth Products Screen Face Kit Ravelle 42 User manual

SCREEN FACE KIT
MODEL RAVELLE™ 42
INSTALLATION INSTRUCTIONS FOR INSTALLING SCREEN
FACE KIT FOR USE WITH THE RAVELLE™ 42 GAS FIREPLACE
775,289M
Rev. A, 10/2008
HEARTH PRODUCTS
KITS AND ACCESSORIES
KIT CONTENTS (See Figure 1):
Please ensure that all these parts are included
1 ea. Screen Face [Complete] (A)
1 ea. Two Upper Brackets w/Screws (B)
1 ea. Two Lower Brackets w/Speed Nuts (C)
1 ea. Mounting Hardware (D)
- 6 ea. #10 Washers
- 6 ea. 10-24 Hex Nuts
- 4 ea. 10-24 Allen Head Screws
- 2 ea. 1/4” 20 Phillips Head Screws
1 ea. Instruction Sheet
Cat. No. Model Description
75029 SCREEN-42 Screen Face, Double Door, Black
A
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE 1
TM
Figure 1 - Kit Contents
TOOLS NEEDED:
Phillips Head Screw Driver
3/8” Socket/nut Driver
5/32” Allen Wrench or T-Handle Wrench
GENERAL INFORMATION
If you encounter any problems, need clarification of these instructions
or are not qualified to properly install this kit, contact you local distribu-
tor or dealer.
Read this instruction sheet in its entirety before beginning the installa-
tion.
All of these parts may scratch and bend, great care should be used
in handling them.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO
THESE INSTRUCTIONS.
TURN OFF THE FIREPLACE AND ALLOW IT TO COMPLETELY COOL
BEFORE PROCEEDING.
INSTALLATION INSTRUCTIONS
Step 1. Ensure the reveal corner is positioned as shown in Figure 1. If it
needs to be adjusted to the position shown in Figure 1, see Page
12 of the Installation and Operation Manual.
D
C
B
Figure 2
Reveal Corner
Adjustment
for Arch Face
ONLY
Reveal Corner Adjusted
for Arch Face
Reveal Corner
Reveal Corner
Expanded View of
Reveal Corner
WRONG

Figure 4
Step 5. Using a phillips screwdriver (through upper grill opening) attach
the screen face to the fireplace starting with the upper brackets.
Screw the upper brackets in part way only, you will tighten them
in step 7.
Step 6. Open the lower door on the screen face and thread the two 1/4”-20
phillips head screws (provided) through the lower hinge mounts
into the speed nuts on lower face brackets, attached to the fireplace
(see Figure 4).
Step 7. Adjust the alignment and depth of the screen face until it sits flush
with the wall and tighten all four mounting screws. DO NOT OVER-
TIGHTEN THE SCREWS.
Step 8. Finish the installation by putting the screen doors back on their
hinges (check to make sure the washers are in place).
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Step 2.Using a 5/32” allen wrench, remove the lower face brackets on
the fireplace and replace with the lower brackets (C) using the
four 10-24 allen head screws provided (see Figures 3 and 4). DO
NOT OVERTIGHTEN THE SCREWS.
Step 3. Using a 3/8” socket or nut driver, attach the two upper mounting
brackets (B in Figure 3)to the six pre-welded studs near the top
rear of the screen face, using the six #10 washers and #10 hex nuts
provided (see Figures 3 and 4). DO NOT OVERTIGHTEN NUTS.
This side of
brackets mount
to fireplace (see
Figure 4)
(B) Upper Face Brackets
(C) Lower Face Bracket
10-24 Allen
Head Screws
Speed Nut
#10 Washers
and Nuts
1/4”-20 Phillips
Head Screws
Screw through the
lower hinge mounts
into the speed
nuts on lower face
brackets
Figure 5 - Completed Installation
Printed in U.S.A. © 2008 Lennox Hearth Products
P/N 775,289M REV. A 10/2008
Lennox reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local
distributor for fireplace code information.
Lennox Hearth Products
1110 West Taft Avenue • Orange, CA 92865
Step 4. Remove the screen doors from the face by gently lifting up and
out of their hinges. Check to make sure the washers that separate
the two halves of the hinge have not fallen off. Set the screen door
aside.
2
Figure 3
u
uA 1/4” screw
with push nut will be
installed on upper
mounting brackets (not
shown). The push nut
holds the screw in place
when installing face.