Lenze i410 User manual

> 3 s
GND
AI1
AI2
AO1
10V
24V
DI1
GND
AI1
AI2
AO1
10V
24V
DI1
DI2
DI3
DI4
DI5
P211.00
P430.03
P430.02 P430.02
P220.00
P221.00
P210.00
AI1
GROUP 4
P420.XX
P420.02
CTRL
R F
V1-0
Group 3 – motor control
Group 4 – I/O seng
Group 5 – network seng
Group 6 – process controller
Group 7 – addional funcons
Group 8 – sequencer
Group 0 – favourites: Quick access to most important parameters (*)
Procedure during commissioning
1. Load default sengs: Set P700.01 = 1
2. Select language: P705.00 1 = English; 2 = German
3. Basic seng of V/f characterisc control:
*P208.01 Set the mains voltage
*P303.01 basic voltage = rated motor voltage
*P303.02 basic frequency = rated motor frequency
*P210.00 minimum frequency [Hz]
*P211.00 maximum frequency [Hz]
*P220.00 acceleraon me [s]
*P221.00 delay me [s]
*P430.02 analog input 1: Minimum frequency [Hz]
*P430.03 analog input 1: Maximum frequency [Hz]
Control of inverter by means of keypad
Define keypad as control source and setpoint source:
*P200.00 = 1 (keypad as control source)
*P201.01 = 1 (keypad as setpoint source)
Operaon:
Change direcon of rotaon
Change setpoint frequency
Start/stop motor
Connecon:
Define preset frequency values:
[Hz]
[Hz]
[Hz]
Connecon:
I/O terminals
or
Inverter i410 - Quick start
Operaon of keypad
Example: P420.02
Group 0 – favourites
Group 1 – diagnoscs
Group 2 – basic seng
Control of inverter by means of terminals (default seng)
Time
Frequency
Save parameters: Flashes = Not saved On = saved)
EN-gb
(
Setpoint frequency
10 VDC supply
24 VDC, 100 mA supply
Start
GND
* P450.01 setpoint frequency: Preset freq.val. 1
* P450.02 setpoint frequency: Preset freq.val. 2
* P450.03 setpoint frequency: Preset freq.val. 3
Define input range of analog input 1:
[Hz]
[Hz]
* P430.02 minimum frequency
* P430.03 maximum frequency
Navigaon in the menu
Parameter alteraon
Go to Menu/Parameters
Confirm parameter
Quit Menu/Parameters
CTRL
Keypad control
Start motor
R F
Change direcon of rotaon
Stop motor
I/O seng
Fct. dig. outputs
DO1 funcon
Setpoint frequency
10 VDC supply
24 VDC, 100 mA supply
Start
Reset error
Change direcon of rotaon
Acvate preset (bit 0)
Acvate preset (bit 1)
GND
13560189

GND
AI1
AI2
AO1
10V
24V
DI1
DI2
DI3
DI4
DI5
GND
DO1
NO
COM
NC
U/I
V1-0
*P201.01
(configured AI1 as standard
setpoint)
*P400.02
Preset 01 (*P450.01)
*P100.00 output frequency
*P103.00 current actual value
Default seng
*P400.04
*P400.13
Start
Reset error
Mark direcon of rotaon
Acvate preset (bit 0)
Acvate preset (bit 1)
DO1 acvated at
Release brake
Relay acvated at
Ready for operaon
Analog input 1
Analog input 2
Analog output 1
10 VDC supply for potenometer
24 VDC, 100 mA supply, reference for digital inputs
Digital input 1
Digital input 2
Digital input 3
Digital input 4
Digital input 5
Digital output 1
GND for analog and digital signals
Relay NO contact
Relay centre contact
Relay NC contact
bit 1 bit 0 Preset frequency values
0
0
1
1
1
1
Preset 02 (*P450.02)
Preset 03 (*P450.03)
– Select standard setpoint source *P201.01.
– Run forwards/backwards [stac signals], start forwards/backwards [edge controlled]
– Enable quick stop *P400.03: Bring motor to a standsll in best me.
– Jog forwards *P400.10: Let motor rotate forwards with setpoint preset 05 (CW).
– Jog backwards *P400.11: Let motor rotate backwards with setpoint preset 06 (CCW).
Diagnoscs
P102.00 setpoint frequency [Hz]
P125.01 acve control source
P125.02 acve setpoint source
*P430.01 (0 ... 10 VDC signal)
*P430.02 — *P430.03
*P400.18
*P400.19
*P420.02
*P420.01
RDY
ERR
Meaning
off
off
No supply voltage.
2 Hz
off
Inverter inhibited.
Inverter inhibited, no DC-bus voltage.
Inverter inhibited, warning acve.
Inverter inhibited, error acve.
off
Inverter enabled and motor rotang or quick stop is acve.
Inverter enabled and motor rotang, warning signalled.
Inverter enabled, quick stop as response to fault acve.
Error message
Cause
Remedy
.2382
Ixt error
Reduce load, adapt ramps
.2383
Ixt warning
.3210
DC-bus overvoltage
Ramp me too short or motor is running in generator
mode
.3211
DC-bus overvoltage warning
.3220
DC-bus undervoltage
Check supply
.3221
DC-bus undervoltage warning
.3222
DC-bus voltage too low for switch-on
.6280
Trigger/funcon incorrectly connected.
In the case of flexible I/O configuraon *P200.01,
Inverter enable *P400.01 or Start *P400.02 must
have been assigned to an I/O. Do not use Start
forwards/backwards and Run forwards/backwards
at the same me.
.FF37
Automac start inhibited.
GND for analog and digital signals
EN-gb
range [Hz]:
config.: