Single-Pole Wiring Application:
Connect wires per WIRING DIAGRAM as follows:
Screw wire nuts on clockwise making sure no bare conductors
show below the wire connectors. Secure each connector with
electrical tape.
NOTE: Control can be installed on either the Load or Line side.
•Green control Ground lead to Green or bare copper
wire in wall box.
•Black control lead to any wall box wire removed
from old switch.
•Red control lead without insulating label to remaining
wall box wire. Proceed to Step 6.
•Remaining Red control lead should have Red insulation
label affixed. Proceed to Step 6.
NOTE: If insulating label is not affixed to Red lead, use a
small wire nut or electrical tape to cap off. Proceed to Step 6.
3-Way Wiring Application:
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for two years from the purchase date. Leviton’s only obligation
is to correct such defects by repair or replacement, at its option, if within such two year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little
Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened,
abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is
required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage
to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
Connect wires per WIRING DIAGRAM as follows:
Screw wire nuts on clockwise making sure no bare
conductors show below the wire connectors. Secure each
connector with electrical tape.
NOTE: Control can be installed on either the Load or Line side.
•Green control Ground lead to Green or bare copper wire
in wall box.
•Black control lead to tagged (common) wall box wire
identified when removing old switch.
•Remove Red insulating label from Red lead.
•Any Red control lead to any of the remaining
wall box wires.
•Remaining Red control lead to remaining wall box wire.
Testing your Fan Speed Control prior to
mounting in wall box:
Fan Speed Control Mounting:
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.
Step 7
Restore Power: Restore power at circuit breaker or
fuse. Installation is complete.
OPERATION
NOTE: The indicator light will illuminate when the control is in the
OFF position to facilitate access in the dark.
NOTE: If using the control in a 3-way application, the control will
turn ON at the speed level set on the control's slide lever. The fan
can be controlled from either the control or the switch location.
TROUBLESHOOTING
•Fan does not turn ON and ON/OFF LED does not turn ON
- Circuit breaker or fuse has tripped.
- Fan has burned out.
- Fan Neutral connection is not wired.
NOTE: If further information is needed in identifying the HOT wire
in a 3-Way application, go to
Leviton's website at www.leviton.com.
For non-standard wiring applications, refer
to Wire Nut and Connector Size Chart
DI-000-IPF01-02B
Step 5b
Step 5b
con’t
•Restore power at circuit breaker or
fuse.
•Carefully holding control as
shown, move slider control lever to
highest position. Fan should turn
ON to highest level. If fan does not
turn ON, depress push-button switch
once. Fan should turn ON to highest
level. Position slider to the remaining
levels: MEDIUM (middle of stroke)
and LOW (bottom of stroke). Fan
speed should change accordingly.
If fan still does not turn ON, refer
to the TROUBLESHOOTING
section.
Installation may now be completed
by carefully positioning
all wires to provide room in wall box
for control. Mount control
into box with mounting screws
supplied. Attach wallplate.
ON/OFF:
Depress push-button switch to ON
position - Fan will turn ON at level set
by slider.
Depress push-button switch to OFF
position - Fan will turn OFF.
Fan Speed:
Move slider control lever up or down to
one of three levels; HIGH, MEDIUM, or
LOW - Fan will increase or decrease in
speed respectively for desired level.
Insert wires
straight then twist
clockwise
Insert wires
straight then twist
clockwise
Electrical
Tape
Electrical
Tape
