Life Fitness CL5X User manual

Classic Series Cross-Trainer Model CLSX
assembly instructions

2
Congratulations...
and welcome to the world of
The following Parts List and the step-by-step assembly procedures have been assembled
to make the set-up of the Cross-Trainer as quick and easy as possible.
Please take special note of the following important points prior to choosing a location and
beginning assembly of the Cross-Trainer.

3
IMPORTANT SAFETY INSTRUCTIONS!
±DO NOT locate the cross-trainer outdoors, near swimming pools, or in areas of high humidity.
±DO NOT operate your cross-trainer if it has been dropped, damaged, or even partially immersed in water. If this
occurs, contact life fitness customer support services at the number in the operation manual.
±DO NOT locate the cross-trainer any closer than 30 inches (76 cm) to a television set.
±DO NOT locate additional cross-trainers any closer than 42 inches (107 cm) from center to center to avoid
interference (cross talk) between heart rate monitors.
±DO keep the area around your cross-trainer clear of any obstructions, including walls and furniture. Ensure that there
is at least a 12 inch (30cm) clearance in front of the cross-trainer.
±DO verify the contents of the delivery carton against the accompanying parts list prior to setting the cartons and
shipping material aside. If any parts are missing, contact life fitness customer support services at the number listed
in the operation manual. Save the shipping cartons in case of return.
±DO read the entire operation manual prior to attempting to operate this machine as this is essential for proper use.
CONSIGNES DE SECURITE IMPORTANTES!
±NE placez pas l'appareil à l'extérieur, près d'une piscine ou dans un endroit très humide.
±NE faites pas fonctionner l'appareil s'il est tombé, s'il a été endommagé ou s'il a été partiellement plongé dans l'eau.
Si cela s'est produit, contactez le service après-vente de life fitness au numéro fourni dans le manuel d'utilisation.
±NE placez pas l'appareil à moins de 76 cm d'un poste de télévision.
±NE placez pas d'autres appareils du même type à proximité. un espace d'au moins 107 cm doit être observé entre
les parties centrales de deux appareils afin d'éviter les interférences entre les contrôleurs de rythme cardiaque.
±MAINTENEZ la zone autour de l'appareil libre de toute obstruction, y compris murs et meubles. veillez à laisser un
dégagement d'au moins 30 cm devant l'appareil.
±VÉRIFIEZ si l'emballage contient toutes les pièces de la liste jointe avant de le mettre de côté. si des pièces sont
absentes, contactez le service après-vente de life fitness au numéro indiqué dans le manuel d'utilisation. conservez
l'emballage au cas où vous devriez renvoyer l'appareil.
±LISEZ le manuel de l'utilisateur tout entier avant d'essayer de faire fonctionner cet appareil. ceci est indispensable à
son utilisation correcte.

4
T OOLS R EQUIRED FOR A SSEMBLY ... Magnetic #2 Bit Phillips Screwdriver, 5/16" & 3/16" Hex Key Wrench, 1/2" Open End
Wrench
Parts Description
1 Hex socket Head Cap Screw Qty: 8
3/8-16 x 1"
0017-00101-1645
2 Phillips Pan Head Screw Qty: 8
#8-18 x 10
0017-00101-1744
3 Phillips Pan Head Screw Qty: 14
#8-18 x 3/4"
0017-00101-1242
4 ConsoleAssembly Qty: 1
5 Front Monocolumn Cover Qty: 1
0K61-06350-0003
6 Back Monocolumn Cover Qty: 1
0K61-06351-0003
7 Console SupportAssembly Qty: 1
AK61-00500-0015
8 Flat Washer Qty: 2
0017-00104-0192
9 Left Front Cover Qty: 1
0K61-06240-0002Parts Description
10 Right Front Cover Qty: 1
0K61-06250-0002
Parts Description
11 Left UserArmAssembly Qty: 1
AK61-00178-0002
12 Right UserArmAssembly Qty: 1
AK61-00178-0001
13 Front Rocker Cover Qty: 2
0K61-06340-0003
14 Back Rocker Cover Qty: 2
0K61-06341-0003
15 Foam Isolator (Polar® Receiver) Qty: 1
0K36-01059-0002
16 Polar® Receiver Qty: 1
AK40-00045-0001
17 Accessory Tray Qty: 1
0K63-01030-0001
18 Internal Tooth Lock Washer Qty: 6
0017-00104-0450
19 Cap: Console Support Qty: 1
0K61-01283-0001

5
12
18
38
17628394101251113
PLEASE READ THIS PRIOR TO ASSEMBLY:
This product is preconfigured to accept the addition of the Life Fitness Entertainment System. A
POWER CABLE and COAXIAL CABLE have been pre-installed. If this product is to be installed in
conjunction with the Life Fitness Entertainment System, please read both the product assembly
instructions and Entertainment Ready assembly instructions (included with the Life Fitness
Entertainment System) prior to assembly.
Route the POWER CABLE and COAXIAL CABLE alongside the MAIN WIRE HARNESS where
applicable.

6
1. Before proceeding, familiarize yourself with the parts of the
Cross-Trainer and make sure that you have received all
the items described in the Parts List.
2. Locate the left and right FRONT COVER (#9, #10). Using
two PHILLIPS PAN HEAD SCREWS (#3), mount the
USER LEFT FRONT COVER (#9) to the FRAME (A).
Attach the USER RIGHT FRONT COVER (#10) to the
FRAME in the same manner using two PHILLIPS PAN
HEAD SCREWS (#3). Secure the tops of the FRONT
COVERS together using two PHILLIPS PAN HEAD
SCREWS (#3).
CAUTION: Do not overtighten the PHILLIPS PAN HEAD
SCREWS (#3).
3. Locate the RIGHT USER ARM (#12). Snap the 2-PIN
CONNECTOR (2PA) located at the bottom of the RIGHT
USER ARM into the 2-PIN CONNECTOR (2PB) positioned
at the top of the RIGHT ROCKER ARM (B). Feed the con-
nectors and excess cable up into the RIGHT USER ARM.
Secure the RIGHT USER ARM to the RIGHT ROCKER
ARM using three HEX SOCKET HEAD CAP SCREWS
(#1) and INTERNAL TOOTH LOCK WASHERS (#18).
Repeat the procedure for the LEFT USER ARM (#11) and
LEFT rocker arm (C). Tighten all screws securely.
CAUTION: Be careful not to pinch the WIRE HARNESSES
when assembling the USER ARMS (#11 & #12) to the
ROCKER ARMS (B & C).
4. Detach and unwrap the WIRE HARNESS (E) (16P, 4P)
located at the top of the MONOCOLUMN (F). Holding the
CONSOLE SUPPORT ASSEMBLY (#7) with the handgrips
facing upward, feed the WIRE HARNESS up through the
neck and out the top access hole. Carefully lower the
CONSOLE SUPPORT ASSEMBLY into the MONOCOL-
UMN.
CAUTION: Be careful not to pinch the WIRE HARNESSES
(E) when assembling the CONSOLE SUPPORT ASSEM-
BLY (#7) to the MONOCOLUMN (F).
5. Using two HEX SOCKET HEAD CAP SCREWS (#1) and
two FLAT WASHERS (#8), secure the CONSOLE SUP-
PORT ASSEMBLY (#7) to the MONOCOLUMN (F).
Tighten the SCREWS securely.
6. Locate the ACCESSORY TRAY (#17). Align the ACCES-
SORY TRAY with the bottom of the DISPLAY CONSOLE
(#4) as shown. Using four MOUNTING SCREWS (#2),
secure the ACCESSORY TRAY to the DISPLAY CON-
SOLE as shown. Tighten the SCREWS securely.
CAUTION: Do not overtighten the MOUNTING SCREWS
(#2).

7
7. Attach the 4-PIN (4P), 3-PIN (3P), and 16-PIN (16P) CON-
NECTORS to the corresponding JACKS on the back of the
CONSOLE ASSEMBLY (#4).
8. Feed any excess WIRE HARNESS (E) down into the
CONSOLE SUPPORT ASSEMBLY (#7). Secure the CON-
SOLE ASSEMBLY (#4) to the CONSOLE SUPPORT
ASSEMBLY using four PHILLIPS PAN HEAD SCREWS
(#2). Tighten the SCREWS securely.
CAUTION: Do not over-tighten the PHILLIPS HEAD PAN
SCREWS (#2).
CAUTION: Be careful not to pinch the WIRE HARNESS
(E) when assembling the CONSOLE ASSEMBLY (#4) to
the CONSOLE SUPPORT ASSEMBLY (#7).
9. Locate and install the CONSOLE SUPPORT CAP (#19)
onto the CONSOLE SUPPORT ASSEMBLY (#7) as
shown.
10. Locate the POLAR RECEIVER (#16). Slide the FOAM
ISOLATOR (#15) over the POLAR RECEIVER. Remove
the POLAR RECEIVER JACK (G) from the tape and plug
the POLAR RECEIVER into the POLAR RECEIVER JACK.
11. Locate the FRONT and BACK MONOCOLUMN COVERS
(#5 & #6). With the WIRE positioned on top, carefully
insert the POLAR RECEIVER (#16) between the vertical
ribs located inside the BACK MONOCOLUMN COVER
(#6).
Place the BACK MONOCOLUMN COVER (#6) over the
PIVOT SHAFT (H) at the top of the MONOCOLUMN (F).
NOTE: The POLAR RECEIVER WIRE must be positioned
on top when inserted into the REAR MONOCOLUMN
COVER (#6).
12. Place the FRONT MONOCOLUMN COVER (#5) on the
opposite side of the BACK MONOCOLUMN COVER (#6)
to cover the PIVOT SHAFT (G) and CONSOLE SUPPORT
ASSEMBLY MOUNTING SCREWS. Interlock the top tabs
and use two PHILLIPS PAN HEAD SCREWS (#3) to
secure the bottoms of the MONOCOLUMN COVERS
together. Tighten the SCREWS securely.
CAUTION: Do not over-tighten the PHILLIPS PAN HEAD
SCREWS (#3).
13. Locate one FRONT ROCKER COVER (#13) and one
BACK ROCKER COVER (#14). Position the FRONT
ROCKER COVER over the user side of the left end of the
PIVOT SHAFT (H) (as shown) making sure that it inter-
locks with the MONOCOLUMN COVERS (#5 & #6). Place
the BACK ROCKER COVER over the opposite side of the
left end of the PIVOT SHAFT in the same manner. Secure
the COVERS using three PHILLIPS PAN HEAD SCREWS
(#3). Repeat the procedure reversing front and back for the
user right end of the PIVOT SHAFT.
CAUTION: Do not over-tighten the PHILLIPS PAN HEAD
SCREWS (#3).

©2008 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness is trademark of Brunswick Corporation.
Polar is a registered trademark of Polar Electro, Inc. MO51-00K61-A122 04/08
Before attempting to operate your Cross-Trainer, it is imperative that you familiarize yourself with the contents of the
Operation Manual. If your Cross-Trainer does not respond as described in the Operation Manual, contact the nearest
Life Fitness service center as listed in the Operation Manual.
[phone] or [phone]
Prior to your call, please be sure you have located and noted the
MODEL NUMBER & SERIAL NUMBER.
The Model & Serial number information of your Life Fitness Cross-Trainer is listed on a label
located on the rear stabilizer.
8
PHYSICAL DIMENSIONS:
Length: 83 inches / 211 centimeters
Width: 28 inches / 71 centimeters
Height: 61 inches / 155 centimeters
Weight: 235 pounds / 106.5 kilograms
PRE-OPERATION CHECKLIST
• Ensure that all fasteners are tight.
• Make sure the CROSS-TRAINER is properly leveled and stable.
(Refer to the Operation Manual)
• Ensure that the Leveler Jam Nuts are tight.
(Refer to the Operation Manual)
• Read the entire Operation manual before using the Cross-Trainer.
LISTE DES VÉRIFICATIONS À EFFECTUER AVANT L'UTILISATION
• Vérifiez si tous les dispositifs de fixation sont serrés.
• Vérifiez si le CROSS-TRAINER est de niveau et stable.
(Référez-vous au manuel d'utilisation.)
• Vérifiez si les contre-écrous des vérins de mise à niveau sont serrés.
(Référez-vous au manuel d'utilisation.)
• Lisez le manuel d'utilisation dans son intégralité avant d'utiliser le cross-trainer.

Classic Series Cross-Trainer Model CLSX
INSTRUCTIONS DE MONTAGE

2
Félicitations...
et bienvenue dans le monde de
La liste de pièces suivante et les instructions d'installation détaillées sont fournies afin
de rendre l'installation de cet appareil aussi facile et rapide
que possible.
Portez une attention toute particulière aux points suivants avant de choisir un
emplacement et de commencer à monter le Cross-Trainer.