Life Fitness Club Machine User manual

CLUB SERIES POWER RACK
Part # 72xxxx
RevA. Revision:4/18/021
ASSEMBLY INSTRUCTIONS

PARTS LIST
PART #
72545
72550
72553
72555
72560
72564
72565
71126
68071
KEY
1
2
3
4
5
6
7
8
9
QTY
2
1
1
1
1
1
2
6
2
KEY
10
11
12
13
14
15
16
17
OR
PART #
3102922
3102905
3102906
3102807
3102514
6866701
6866601
6866602
6866603
DESCRIPTION
3/8 X 2-3/4” BOLT
3/8 X 3-3/4” BOLT
3/8 X 4” BOLT
3/8” LOW HEIGHT LOCK NUT
3/8” SAE WASHER
3/8” RH WASHER
BLACK RH CAP
WHITE RH CAP
PLATINUM RH CAP
QTY
4
26
4
32
58
66
18
48
48
DESCRIPTION
SIDE
TOP CROSS SUPPORT
RIGHT RAIL
LEFT RAIL
CHIN UP-SUPPORT
BOTTOM CROSS SUPPORT
REAR UPRIGHT
WEIGHT HORN
SMART RACK
BOLT LENGTH
Tools Required for Assembly
2
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
* Rubber mallet or hammer
* 9/16” wrench
* Ratchet with 9/16” socket
* 3mmAllen wrench

3
10 3/8 X 2-3/4” BOLT
12 3/8 X 4” BOLT
13
3/8” LOW
HEIGHT LOCK
NUT
14
3/8” SAE
WASHER
17
RH CAP
(BLACK/WHITE/PLATINUM)
15
RH
WASHER
11 3/8 X 3-3/4” BOLT
16

STEP 1:
FIGURE 1
4
• LOOSELY assemble the two SIDES (1) to the TOP CROSS SUPPORT (2) and the CHIN-UP SUPPORT (5) using fourteen RH
CAPS (17), eight 3/8 X 3-3/4” BOLTS (11), fourteen 3/8” SAE WASHERS (14), fourteen 3/8” RH WASHERS (15) and six 3/8”
LOW HEIGHT LOCK NUTS (13) as shown in FIGURE 1.
11 3/8 X 3-3/4”
5
2
17
14
15
1
0123456
1/2 1/2 1/2 1/2 1/2 1/2

5
STEP 2:
FIGURE 2
11 3/8 X 3-3/4”
7
1
• LOOSELY assemble the two REAR UPRIGHTS (7) tot the SIDES (1) using sixteen RH CAPS (17), eight 3/8 X 3-3/4” BOLTS
(11), eight 3/8” SAE WASHERS (14), sixteen 3/8” RH WASHERS (15) and eight 3/8” LOWHEIGHT LOCK NUTS (13) as shown
in FIGURE 2.
17
15 13
14

6
STEP 3:
FIGURE 3
0123456
1/2 1/2 1/2 1/2 1/2 1/2
• LOOSELY assemble the BOTTOM CROSS SUPPORT (6) to the REAR UPRIGHTS (7) and two WEIGHT HORNS (7) using four
BLACK RH CAPS(16), four RH CAPS (17), four 3/8 X 4” BOLTS (12), eight 3/8” SAE WASHERS (14), eight 3/8” RH WASH-
ERS (15) and four 3/8” LOW HEIGHT LOCK NUTS (13) as shown in FIGURE 3.
3/8 X 4” 12
16
1415 8
17
6
7

7
STEP 4:
FIGURE 4
•Securelytighten all looseframe connections madeto this point,then proceedtosnap RH CAPS(16
& 17) over the RH WASHERS (25) on all tightened connections.
TIGHTEN!
TIGHTEN!
TIGHTEN!
TIGHTEN!

8
0123456
1/2 1/2 1/2 1/2 1/2 1/2
STEP 5:
FIGURE 5
• SECURELY assemble the WEIGHT HORNS (7) to the REAR UPRIGHTS (7) using sixteen BLACK RH CAPS(16), sixteen RH
CAPS (17), eight 3/8 X 3-3/4” BOLTS (11), sixteen 3/8” SAE WASHERS (14), sixteen 3/8” RH WASHERS (15) and eight 3/8”
LOW HEIGHT LOCK NUTS (13) as shown in FIGURE 5.
3/8 X 3-3/4” 11
16
1415 8
7
17
13

9
STEP 6:
FIGURE 6
16
9
• SECURELY assemble the two SMART RACKS (9) to the SIDES (1) using six BLACK RH CAPS (16), six RH CAPS (17), six 3/
8 X 3-3/4” BOLTS (11), twelve 3/8” SAE WASHERS (14), twelve 3/8” RH WASHERS (15) and six 3/8” LOW HEIGHT LOCK
NUTS (13) as shown in FIGURE 6.
1
13
3/8 X 3-3/4” 11
15
14
17

10
STEP 7:
FIGURE 7
• CAREFULLY slide the RIGHT and LEFT RAIL (3 & 4) into the SIDES as shown in FIGURE 7.
4
3
1
0123456
1/2 1/2 1/2 1/2 1/2 1/2