Lightmybricks LEGO Harley-Davidson Fatboy 10269 Lighting... User manual

The following page is the instructions for the Light My Bricks LEGO Harley-
Davidson Fatboy (10269) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow
each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are
wishing to purchase the Light My Bricks LEGO Harley-Davidson Fatboy (10269)
LED light kit , please click here to view the product page
Light My Bricks: LEGO Harley-Davidson Fatboy
10269 Lighting Kit

Package Contents:
5x White 15cm Micro Bit Lights
2x White 30cm Micro Bit Lights
1x Warm White 30cm Large Bit Light
2x Micro 4-Port Expansion Boards
1x 6-Port Expansion Board
2x 5cm Connecting Cable
1x 30cm Connecting Cables
1x RGB Remote Control and RGB Control Board
4x RGB Strip Lights
4x RGB Connecting Cable 15cm
1x USB Power Cable
8x 3M Adhesive Squares
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT forcefully
join LEGO® together around cables; instead ensure they are laying comfortably
in between each stud.

CAUTION: Forcing LEGO® to connect over a cable can result in damaging the
cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing up,
look for the soldered “=” symbol on the left side of the port. The connector side
with the wires exposed should be facing toward the soldered “=” symbol as you
insert into the port. If a plug won’t fit easily into a port connector, do not force it.

Incorrectly inserting the connector can can result in bent pins inside the port
or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.
Connecting Micro Cable connectors to Micro
Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is
similar to connecting lights and cables to Strip Lights. With the expansion
board facing up, ensure the side of the connector with the wires exposed is
facing down. If a plug won’t fit easily into a port connector, do not force it. Use
your fingernail to push the plastic part of the connector to the micro port.

Installing Bit Lights under LEGO® bricks
and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.

OK, Let’s Begin!
1.) We will first install the headlights and the front indicator lights. To start,
disconnect and disassemble the following sections as shown below:

Take a White 30cm Large Bit Light and place it in the centre of the black round
plate. Secure the Large Bit Light in place by reconnecting the trans clear dish
over the top.
Pull down the following section, then thread the connector end of the Bit Light
cable underneath the middle of this section. Pull the cable all the way up from
the top, then reconnect the headlight ensuring the cable of the light is facing
the bottom of the headlight.

2.) Thread the Large Bit Light cable down the light grey technic brick hole on
the right side. Turn the Harley around to the left side and pull the cable all the
way out as shown below:
Thread the cable behind the following bar, then connect the Bit Light to a 6-
Port Expansion Board. Take your USB Power Cable and connect it to the end
port on the expansion board. Connect the USB Connector to a USB Power
Bank or wall adaptor (sold separately) and turn it ON to test the headlight is
working OK.

N ote: If you experience any issues with the lights not working and suspect an
issue with a component, please try a different port on the expansion board to
verify where the fault lies (with the light or expansion board). To correct any
issues with expansion board ports, please view the section addressing
expansion board issues on our online troubleshooting guide.
Reconnect the plate above the headlight, then disconnect the USB Power
Cable from the expansion board. Eliminate excess cable by folding and twisting

the cable around itself a few times into a neat bunch.
3.) We will now install the front indicator lights. First disconnect both of these
sections and disassemble them as shown below: