Lightmybricks LEGO EIFFEL TOWER User manual

LEGO®EIFFEL TOWER #10307
LIGHT KIT
INSTALLATION GUIDE
Part 2 of 2

CONTENTS 2
Contents
LEGO®EIFFEL TOWER 10307 LIGHT KIT INSTALL GUIDE
Instructions: Part 2 4
Final Product 69
Troubleshooting 70
Contact 74

INSTRUCTIONS 3
LEGO®EIFFEL TOWER 10307 LIGHT KIT INSTALL GUIDE
INSINSTRTRUCUCTIONSTIONS
TTo ensuro ensure a smooe a smooth instth installation oallation off yyourour lighlightt kitkit, please r, please read and fead and folloolloww
each steach step cep carareefullfullyy. I. Iff yyou run inou run inttooanany issues, please ry issues, please reefferer tto the onlineo the online
trtroubleshoooubleshooting guideting guide..
Wenn Sie Probleme mit Ihrem Light My Bricks-Set haben, sehen Sie sich unser Video zur Fehlerbehebung an oder
lesen Sie die Auflistung der häufigsten Ursachen, die Ihnen bei der Fehlersuche helfen hier.
Si vous rencontrez des problèmes avec votre kit Light My Bricks, regardez notre vidéo de dépannage ou consultez la
liste des causes les plus fréquentes pour vous aider à les résoudre ici.
Se si verificano problemi con il set Light My Bricks, guardare il nostro video per la risoluzione dei problemi o leggere
l'elenco delle cause più comuni per la risoluzione dei problemi qui.

INSTRUCTIONS 4
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®EIFFEL TOWER 10307 LIGHT KIT INSTALL GUIDE
15cm Connecting Cable
6-Port Expansion Board
RGB IR Control Board
1
NOTE
This is Part 2 of the Eiel
Tower Light Kit Instructions
If you have not completed
Part 1 first, click the box.
Part 1
Links to instructions portal page
Click me!
NOTE
Connect the 15cm Connecting
Cable into the “+5V” port on the
RGB IR Control Board.
NOTE
Ensure the 2nd level of the
Eiel Tower lines up with the
first. The correct side has the
flat plates and studs in the
following locations.

INSTRUCTIONS 5
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®EIFFEL TOWER 10307 LIGHT KIT INSTALL GUIDE
RGB 30cm Connecting Cable
2x Adhesive Square
50cm Connecting Cable
2
3

INSTRUCTIONS 6
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®EIFFEL TOWER 10307 LIGHT KIT INSTALL GUIDE
2x Adhesive Square
NOTE
Twist the 15cm Connecting
Cable and fold it under the
6-Port Expansion Board.
50cm Connecting Cable

INSTRUCTIONS 7
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®EIFFEL TOWER 10307 LIGHT KIT INSTALL GUIDE
4
NOTE
For Steps 4-5, use one 50cm
Connecting Cable while
leaving one 50cm Connecting
Cable for a later step.

INSTRUCTIONS 8
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®EIFFEL TOWER 10307 LIGHT KIT INSTALL GUIDE
NOTE
Bend the loose end of the
Connecting Cable to look like
pictured, to more easily wrap it
around the beams.
5
NOTE
Leave the 50cm Connecting
Cable loose for a later step.

INSTRUCTIONS 9
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®EIFFEL TOWER 10307 LIGHT KIT INSTALL GUIDE
6
RGB Strip Light 2.0
Brick 1x2 - Black
7Tile 1x6 - Black
NOTE
Take the loose RGB Connecting
Cable and thread it up the left
column.

INSTRUCTIONS 10
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®EIFFEL TOWER 10307 LIGHT KIT INSTALL GUIDE
RGB 15cm Connecting Cable
8 9