Lightmybricks LEGO Gingerbread House 10267 Lighting Kit User manual

The following page is the instructions for the Light My Bricks LEGO
Gingerbread House (10267) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow
each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are
wishing to purchase the Light My Bricks LEGO Gingerbread House (10267) LED
light kit , please click here to view the product page
LIGHT MY BRICKS : LEGO Gingerbread House
10267 Lighting Kit

Package Contents:
4x Pink 30cm Bit Lights
2x White 30cm Bit Lights
10x White 15cm Bit Lights
7x Flashing White 15cm Bit Lights
2x White 15cm Micro Bit Lights
1x Micro 4-Port Expansion Board
3x 6-Port Expansion Boards
2x 8-Port Expansion Boards
1x Flicker Effects Board
2x 5cm Connecting Cables
2x 15cm Connecting Cables
2x 30cm Connecting Cable
1x AA Battery Pack (requires 3x AA Batteries)
8x 3M Adhesive Squares
LEGO Pieces:
5x Trans Clear Plate w Rounded Bottom 2×2
2x Trans Orange Round Plate 1×1
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles

providing they are laid correctly between the LEGO® studs. Do NOT forcefully
join LEGO® together around cables; instead ensure they are laying comfortably
in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the
cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing up,
look for the soldered “=” symbol on the left side of the port. The connector side
with the wires exposed should be facing toward the soldered “=” symbol as you
insert into the port. If a plug won’t fit easily into a port connector, do not force it.

Incorrectly inserting the connector can can result in bent pins inside the port
or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.
Connecting Micro Cable connectors to Micro
Expansion Board Ports

Take extra care when inserting the micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is
similar to connecting lights and cables to Strip Lights. With the expansion
board facing up, ensure the side of the connector with the wires exposed is
facing down. If a plug won’t fit easily into a port connector, do not force it. Use
your fingernail to push the plastic part of the connector to the micro port.
Installing Bit Lights under LEGO® bricks
and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.

OK, Let’s Begin!
1.) We will first install lights to the christmas tree on the side of the Gingerbread
House. First disconnect the star followed by the four panel sections around the
tree.

Disconnect the bottom sections from the front of the star as shown below,
then reconnect the 1×2 plate with open studs.
2.) Take a Flashing White 15cm Bit Light and place it in between the two open
studs, in the centre of the star. Secure the Bit Light in place by reconnecting
the trans yellow triangular pieces over the top.

Thread the other end of the Bit Light cable through the gap at the bottom of
the star, then pull the cable all the way out from behind. Reconnect the star to
the tree.

3.) We will now light up the tree panels starting with the two that have the two
trans yellow round plates on them. Take one panel and disconnect the bottom
triangular plate from underneath, then disconnect the trans yellow round plate
from the top.
Take a Flashing White 15cm Bit Light and with the cable facing away from you,
place it directly over the green stud as shown below. Secure the Bit Light in
place by reconnecting the trans yellow round plate over the top.

Disconnect the following few pieces from the bottom of the panel, then take
another Flashing White 15cm Bit Light and with the cable facing the right,
place it over the green stud. Secure the Bit Light in place by reconnecting the
trans yellow round plate, followed by the other pieces we disconnected earlier.