Lightmybricks LEGO HARRY POTTER HUNGARIAN HORNTAIL DRAGON User manual

LEGO®HARRY POTTER
HUNGARIAN HORNTAIL DRAGON
#76406 LIGHT KIT
INSTALLATION GUIDE

INSTALLATION GUIDE 2
Light My Bricks
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
LEGO®HARRY POTTER HUNGARIAN
HORNTAIL DRAGON 76406
INSTALLATION GUIDE
Hi There!
We’re here to help you get started on the LEGO®
Harry Potter Hungarian Horntail Dragon 76406 Light Kit.
This PDF details the instructions for the LED light kit only. If
you are wishing to purchase this product, please click here
to view the product page.
If you run into any issues, please refer to the troubleshooting
section towards the end of this guide.
Have fun and enjoy!

v
PACKAGE CONTENTS 3
PACKAGE CONTENTS: ASSORTED BRICKS:
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
1x Bit Light 30cm - Orange
1x Bit Light Large 30cm - Orange
4x Bit Light Large 15cm - Warm White
1x Expansion Board - 6-Port
1x Eects Board - Flicker
• 1x Plate Round 1x1 Open Stud - Gold
• 3x Plate Round 1x1 Open Stud - Black
• 1x Plate 1x2 Stud Jumper - Black
• 3x Plate Mod 1x1 Rounded w/ Handle - Black
• 3x Tile 1x1 w/ Clip - Black
• 1x Cone 1x1 - Trans Orange
• 2x Bracket 1x1-1x1 - Light Grey
1x Connecting Cable - 5cm
1x USB Power Cable
(Power Source not Included)
+ 4x Adhesive Square

CONTENTS 4
Contents
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
Before You Begin 5
Blueprint 10
Instructions 11
Final Product 24
Troubleshooting 25
Contact 30

BEFORE YOU BEGIN 5
Before You Begin
Laying cables in between
and underneath bricks
Cables can fit in between and underneath
LEGO®bricks, plates, and tiles providing
they are laid correctly between the LEGO®
studs. Do NOT forcefully join LEGO®
together around cables; instead ensure
they are laying comfortably in between
each stud.
CAUTION: Forcing LEGO®to connect over
a cable can result in damaging the cable
and light.
Connecting Cable
Connectors To Expansion
Boards
Take extra care when inserting connectors
to ports of Expansion Boards. Connectors
can be inserted only one way. With the
expansion board facing up, look for the
soldered “=” symbol on the left side of the
port. The connector side with the wires
exposed should be facing toward the
soldered “=” symbol as you insert into the
port. If a plug won’t fit easily into a port
connector, do not force it.
Incorrectly inserting the connector can re-
sult in bent pins inside the port or possible
overheating of the expansion board when
connected.
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE

BEFORE YOU BEGIN 6
Before You Begin
Connecting Cable
Connectors To Strip Lights
Take extra care when inserting connectors
to ports on the Strip Lights. Connectors
can be inserted only one way. With the
Strip Light facing up, ensure the side of
the connector with the wires exposed is
facing down. If a plug won’t fit easily into
a port connector, don’t force it. Doing so
will damage the plug and the connector.
Connecting Micro Cable
Connectors To Micro
Expansion Board Ports
Take extra care when inserting the
micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit
Lights to Micro Expansion Boards is similar
to connecting lights and cables to Strip
Lights. With the expansion board facing
up, ensure the side of the connector with
the wires exposed is facing down. If a plug
won’t fit easily into a port connector, do
not force it. Use your fingernail to push the
plastic part of the connector to the micro
port.
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE

BEFORE YOU BEGIN 7
Before You Begin
Installing Bit Lights Under
Lego® Bricks And Plates
When installing Bit Lights under LEGO®
pieces, ensure they are placed the correct
way up (Yellow LED component exposed).
You can either place them directly on top of
LEGO®studs or in between.
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE

BEFORE YOU BEGIN 8
Before You Begin
Disconnect
Used when you need to
remove a LEGO piece/ section
or LMB component.
Twist/ Braid
Seen when a set of cables
need to be grouped and
twisted together.
Directional
Used to show where to route
cables, place components, or
move them.
Power On Test
Found at the end of a major
step to test the lights. Will be
located in the top left corner.
Bend/Pivot
Used when a component
needs to be bent, or part
folded or pivoted.
Note
Notes will be found alongside
the instruction photos and
explain what to do.
Connect
Used when you need to
connect a LEGO piece or LMB
component.
Turn/ Flip
Will be found in the top left
corner when the set needs to
be rotated or flipped.
Light Kit Component
This is the most important image
format as it indicates which part
to use from the Light Kit. Make
sure you pay close attention to
which part is shown.
The Symbols Used In This Guide
When going through the following guide you will
come across symbols and formats that will assist
with the installation of your light kit. Take notice of
them as each has a specific purpose.
White 30cm Bit Light
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE

BEFORE YOU BEGIN 9
Before You Begin
Disconnect Note
The red coloured note is
used when the topic focuses
on a component being
disconnected or like here, the
removed pieces.
Connect Note
The green coloured note is
used when the topic focuses
on a component being
connected, like the shown
Power Bank.
General Note
This is a sample note that is
used anywhere in this guide. It
will explain a dicult section
where photos are hard to
illustrate or easily confused.
NOTE
Connect to a 5V USB Power Bank,
5V USB Wall Adaptor, or USB to AA
Battery Pack (sold separately)
NOTE
You should have these parts left
over that were removed from the
LEGO set
NOTE
Take the 5cm Connecting Cable
from the 4-Port Micro Expansion
Board and route it into the “IN”
port of the Flicker Eects Board
x2
Connect Focus
Used to highlight a hard to
see area where a component
is being connected.
Disconnect Focus
Used to highlight a hard to
see area where a component
is being disconnected.
General Focus
Used to highlight a hard to
see area where a component
needs to be acted on.
Repeat Step
Repeat the previous step eg.
Make a spotlight, then make a
second spotlight.
Removed Pieces
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE

BLUEPRINT 10
BLUEPRINT
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE

INSTRUCTIONS 11
INSTRUCTIONS
To ensure a smooth installation of
your light kit, please read and follow
each step carefully. If you run into
any issues, please refer to the online
troubleshooting guide.
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE

INSTRUCTIONS 12
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
1
2
Cone 1 x 1 - Trans Orange
NOTE
Ensure the Cone is rotated to
be in this position, with the
Technic axle being horizontal
and vertical.
Orange 30cm Large Bit Light

INSTRUCTIONS 13
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
3
NOTE
Use the LEGO Brick Separator
Tool or similar to pry o the
dicult pieces.

INSTRUCTIONS 14
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
4

INSTRUCTIONS 15
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
5Flicker Eects Board NOTE
Connect the Large Orange Bit
Light into the “OUT” port of the
Flicker Eects Board.

INSTRUCTIONS 16
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
6
7Orange 30cm Bit Light

INSTRUCTIONS 17
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
8
5cm Connecting Cable
6-Port Expansion Board
NOTE
Connect the Orange Bit Light
into the “OUT” port of the
Flicker Eects Board.
NOTE
Connect the 5cm Connecting
Cable into the “IN” port of the
Flicker Eects Board.

INSTRUCTIONS 18
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
9
USB Power Cable
NOTE
Connect to a 5V USB Power
Bank, 5V USB Wall Adaptor, or
USB to AA Battery Pack (sold
separately)
If you experience any issues with the
lights not working and suspect an issue
with a component, please try a dierent
port on the expansion board to verify
where the fault lies (with the light or
expansion board). To correct any issues
with expansion board ports, please view
the section addressing expansion board
issues in our troubleshooting section.
!
!
Round Plate 1x1 Open Stud - Gold

INSTRUCTIONS 19
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
10
Warm White Large 15cm Bit Light
Warm White Large 15cm Bit Light
Round Plate 1x1 Open Stud - Black

INSTRUCTIONS 20
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO®HARRY POTTER HUNGARIAN HORNTAIL DRAGON 76406 LIGHT KIT INSTALL GUIDE
11
x3
Bracket 1x1 - Light Grey
Tile 1x1 W/ Clip Round Edges -
Black
Plate 1x1 Mod Rounded W/ Handle
- Black